Supersonic SC-1126BT Bluetooth Multimedia Speaker System

FCC Compliance

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference.
2. This device must accept any interference received, including interference that may cause undesired operation.

CAUTION: Changes or Modifications not expressly approved by the party responsible could void the user's authority to operate this device.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

This equipment complies with the FCC RF radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20 centimeters between the radiator and your body.

Warranty

Supersonic Inc. ("Supersonic") warrants this product to the original purchaser ONLY, to be free from defects in materials and workmanship under normal use, for ninety (90) DAYS from the date of original purchase. Proof of purchase (receipt) required. Please visit https://www.supersonicinc.com/pages/warranty for additional information.

Playback Modes

USB FLASH CARD PLAYBACK

Note: Make sure your music Playlist is in MP3 Format for best Sound Mode.

Insert USB Flash Drive and Press "MODE" Button until it switches to USB. It will detect it automatically, and begin playing your first MP3 song at the top of your Playlist.

• Press [❚❚] Button to Pause/Continue playing music.
• Press [▶️] Button to go to next song.
• Press [◀️] Button to go to previous song.

SD/MMC PLAYBACK

Insert SD Card/MMC and Press "MODE" Button until it switches to SD. It will detect it automatically, and begin playing your first MP3 song at the top of your Playlist.

• Press [❚❚] Button to Pause/Continue playing music.
• Press [▶️] Button to go to next song.
• Press [◀️] Button to go to previous song.

(Visual Description: Icons indicating USB Flash Drive (Version 2.0 or later) and Micro SD Card (SD type 4 or later) are shown.)

Remote Functions

Note: To use the Remote Control, make sure to remove the plastic battery cover.

• Power ON/OFF: Turns the system on or off.
• Change MODE (MODE): Cycles through FM, BT (Bluetooth), USB, SD/MMC modes.
• MUTE: Mutes or unmutes the audio.
• Prev/Vol-: Goes to the previous song or FM station. Press and hold to decrease volume.
• Next/Vol+: Goes to the next song or FM station. Press and hold to increase volume.
• Play/Pause (❚❚): Plays or pauses music. In FM Mode, press once to start FM Auto Preset Scan.
• EQ: Selects equalizer sound modes (E1= Standard, E2= Classic, E3= Rock, E4= Pop, E5= Jazz, E6= Dance).
• RPT: Repeats the current track or all tracks in USB/SD mode.

(Visual Description: A remote control with buttons labeled Power ON/OFF, MODE, MUTE, EQ, VOL-, VOL+, Play/Pause, RPT. EQ options E1-E6 are listed: Standard, Classic, Rock, Pop, Jazz, Dance. A note indicates "FM" MODE AUTO SCAN and "Select Number Code to go to Auto Preset FM Station or Track # on SD/USB Mode".)

Front Panel

(Visual Description: The front panel shows two satellite speakers and a subwoofer. The subwoofer has a USB port, an SD card slot, a power button, a "BASS" control knob, and a "VOLUME" control knob. The "VOLUME" knob indicates clockwise increases volume and counter-clockwise decreases volume. A front remote sensor ("IR") is also visible.)

The Main Technology Specifications

Set Up Speakers & Woofers

Please Follow the steps below.

COMPOSITION

• Wooden Cabinet For Sub-Woofer: 1 pcs
• Satellite Speakers: 2 pcs
• Sub Woofer: 1 pcs
• Signal Input Cable: 1 pcs
• FM Antenna: 1 pcs
• Operation Manual: 1 pcs
• Remote Control: 1 pcs

THE SETTING AND CONNECTION CHART

(Visual Description: A diagram shows the back of the subwoofer unit. It has labels for AC IN (with a power adapter symbol), INPUT (L/R RCA jacks), OUTPUT (L/R RCA jacks), FM Antenna input, and a power input jack. Two satellite speakers are shown, with cables connecting from the subwoofer's OUTPUT jacks to the speakers. A power adapter is shown connecting to the AC IN jack. A separate diagram shows the power connection: AC/DC Cord connects to POWER input.)

CAUTION:

1. The apparatus shall not be exposed to dripping or splashing and that no objects filled with liquids, such as vases, shall be placed on the apparatus.
2. The mains plug is used as the disconnect device; the disconnect device shall remain readily operable.

FRONT VIEW

(Visual Description: The front view of the subwoofer shows a "BASS" control knob and a "VOLUME" control knob. The "VOLUME" knob has indicators for increasing volume clockwise and decreasing volume counter-clockwise. An "IR" Front remote sensor is also visible.)

STEP 1: Connect AC/DC Cord

Connect the AC/DC Cord to the POWER input on the subwoofer.

STEP 2: Connect L & R Speakers to "OUTPUT" Jacks

Connect the cables from the satellite speakers to the corresponding L and R OUTPUT jacks on the subwoofer.

STEP 3: Power ON

Connect the AC/DC adapter to a power outlet and turn on the system.

Function Guide

(Visual Description: The rear panel of the subwoofer unit is shown with various ports and controls.

• USB: USB port for flash drives.
• SD/MMC: SD/MMC card slot.
• MODE: Button to change modes (FM/AUX/BT/USB/SD/MMC).
• PREV/VOL-: Previous track/station or decrease volume (press and hold).
• NEXT/VOL+: Next track/station or increase volume (press and hold).
• PLAY/PAUSE: Play/pause music. In FM Mode, press once to start FM Auto Preset Scan.
• LED: Indicator Light.
• AUDIO OUTPUT JACKS (L/R): RCA jacks for connecting satellite speakers.
• INPUT JACKS (L/R): RCA jacks for connecting external audio sources like computers or DVD players.

NOTE: If Connecting AUDIO INPUT see diagram; Laptop/PC Computer/TV/DVD/Blueray/etc. Use the "INPUT" Audio Jacks and press "MODE" AUX Line IN.

(Visual Description: A diagram shows how to connect the system to a computer or DVD player using RCA audio cables from the computer's/DVD player's audio output to the subwoofer's INPUT jacks. The diagram also shows a USB flash card inserted into the USB port and a Micro SD card inserted into the SD/MMC slot.)

Use the AUDIO LINE to connect the IN EYELET and the OUT FREQUENCY SIGNAL of the Computer Sound Card or VCD FREQUENCY SIGNAL etc.

(Visual Description: A simplified diagram shows a computer with audio output connected via a cable to the subwoofer's INPUT jacks. Another diagram shows a DVD player connected similarly.)

(Visual Description: A "MADE IN CHINA" label is visible.)

Bluetooth Functions

NOTE: To use the Remote Control, make sure to remove the plastic battery cover.

Press "MODE" Button until the LED Light turns BLUE. You will hear a Beep Sound. Go to your smartphone or Bluetooth Device and turn on Bluetooth Signal. Make sure you select "Allow Device to Connect" on your smartphone or Bluetooth Device, and press SEARCH. "SC-1126BT" will display on your Device, then press "PAIR". Device will pair and you are connected. No Password should be required, but if it does: "0000". Make sure you increase (raise) the volume on your smartphone to have good sound.

Radio Functions

FM Function:

NOTE: Pull out Antenna Wire straight up, before you start to tune in FM Stations.

Press "MODE" Button until it switches to FM Mode. Press [❚❚] Button to begin Auto Scan for FM Stations. It will store (preset) and assign your FM Stations automatically.

• Press one time [▶️] Button to go to next FM Station.
• Press one time [◀️] Button to go to previous FM Station.

NOTE: Will not Preset FM Stations Manually. Will only Preset Automatically from CH01-CH28 and will assign each Strong Frequency FM Station.