Lithonia Lighting LED Sconce Diffuser Installation Instructions

Important Safety Instructions

WARNING: RISK OF ELECTRICAL SHOCK ⚡

• Turn off electrical power at fuse or circuit breaker box before wiring fixture to the power supply.
• Turn off the power when you perform any maintenance.
• Verify that supply voltage is correct by comparing it with the luminaire label information.
• Make all electrical and grounded connections in accordance with the National Electrical Code and any applicable local code requirements.
• All wiring connections should be capped with UL approved wire connectors.

CAUTION: RISK OF INJURY ⚠️

• Wear gloves and safety glasses at all times when removing luminaire from carton, installing, servicing or performing maintenance.
• Avoid direct eye exposure to the light source while it is on.
• Account for small parts and destroy packing material, as these may be hazardous to children.

WARNING: RISK OF BURN ?

• Allow fixture to cool before handling. Do not touch enclosure or light source.
• Do not exceed maximum wattage marked on luminaire label.
• Follow all lamp manufacturer's warnings, recommendations and restrictions for: driver type, burning position, mounting locations/methods, replacement, and recycling.
• Use only lamps that comply with ANSI standards.

CAUTION: RISK OF FIRE ❗

• Keep combustible and other materials that can burn away from luminaire and lamp/lens.
• Minimum 90° C supply conductors.

General Precautions:

• Before installing, servicing, or performing routine maintenance upon this equipment, follow these general precautions.
• Commercial installation, service and maintenance of luminaires should be performed by a qualified licensed electrician.
• For Residential installation: If you are unsure about the installation or maintenance of the luminaires, consult a qualified licensed electrician and check your local electrical code.
• DO NOT INSTALL DAMAGED PRODUCT!
• Recycle: For information on how to recycle LED electronic products, please visit www.epa.gov.
• This fixture should not be used in areas with limited ventilation or high ambient temperatures.
• This fixture is intended to be connected to a properly installed and grounded UL listed junction box.
• These instructions do not purport to cover all details or variations in equipment nor to provide every possible contingency to meet in connection with installation, operation, or maintenance. Should further information be desired or should particular problems arise which are not covered sufficiently for the purchaser's or owner's purpose, this matter should be referred to Acuity Brands Lighting, Inc.

General Installation Notes

Protect yourself. Before installing, read these instructions carefully and save them for future reference.

Date Installed: _________________________

Note: Turn off power at circuit breaker box prior to proceeding!

Fixture Packing List

Installation Instructions

Installation for DLSD3 & DLSD4

1. Rotate or position Sconce housing (1) so LED's are at the top and the drivers are on the bottom. (See Figure 1)

2. DLSD3: Install Mounting Bracket (3) by inserting Screw (4) through the mounting bracket hole and securing it to the housing. Install a second screw through the slot in the bracket and secure it to the housing. (See Figure 1). Align the holes in the Diffuser (2) with the holes in the mounting bracket and secure with Screws (5). (See Figure 2).

3. DLSD4: Align the holes in the Slotted Panel (8) with the holes on top of the mounting bracket and secure with Screws (5) as shown in Figure 3. Install panels as shown in Figure 4. Slide the Trim Assembly (9) onto the slotted diffuser panel, aligning holes, and secure with Screw (10). (See Figure 5).

Installation for DLSD1, DLSD2, DLSD5, DLSD7, DLSD8, DLSD9, DLSD10, DLSD11, DLSD12, DLSD16 & DLSD17

1. Install Mounting Brackets (3) by inserting Screw (4) through the mounting bracket hole and securing it to the housing. Install a second screw through the slot in the bracket and secure it to the housing. (See Figure 6).

2. For DLSD7, DLSD8, DLSD9 & DLSD17: Align holes in the Prong Assembly (7) with holes in the bottom of the mounting brackets and secure with Screws (5). (See Figure 7). Position and hold the Diffuser (2) in the grooves on the installed prong assembly while aligning holes in the second prong assembly with holes in the top of the mounting bracket and secure with Screws (5). (See Figure 8).

3. For DLSD1, DLSD2, DLSD5, DLSD10, DLSD11, DLSD12, & DLSD16: Position the Diffuser (2) over the Mounting Brackets (3) while aligning holes in the diffuser with holes in the brackets, secure with Screws (5). (See Figure 8).

Installation for DLSD6

1. Install Mounting Bracket (3) by inserting Screw (4) through the mounting bracket hole and securing it to the housing. Install a second screw through the slot in the bracket and secure it to the housing. (See Figure 1). Align holes in the Diffuser (2) with holes in the mounting bracket and secure with Screws (5). (See Figure 2).

Installation for DLSD13, DLSD14 & DLSD15

1. Install Screws (11) into the outermost holes in the Mounting Bracket (3). (See Figure 9).

2. Install the mounting bracket by inserting Screw (4) through the bracket hole and securing it to the housing. Install a second screw through the slot in the bracket and secure it to the housing. (See Figure 9).

3. Align the slots in the rear of the diffuser (2) with the mounting bracket screws and secure with Thumb Nuts (6). (See Figure 10).

Diagrams and Figures Description

Figure 1: Illustrates the installation of the Mounting Bracket (3) to the Sconce Housing (1) using Screws (4). This figure is relevant for DLSD3, DLSD4, and DLSD6 installations.

Figure 2: Shows the attachment of the Diffuser (2) to the Mounting Bracket (3) using Screws (5). This figure is relevant for DLSD3, DLSD4, and DLSD6 installations.

Figure 3: For DLSD4, depicts aligning the Slotted Panel (8) with the Mounting Bracket (3) using Screws (5).

Figure 4: For DLSD4, illustrates the installation of panels.

Figure 5: For DLSD4, shows sliding the Trim Assembly (9) onto the slotted diffuser panel and securing it with Screw (10).

Figure 6: For models DLSD1, DLSD2, DLSD5, DLSD7, DLSD8, DLSD9, DLSD10, DLSD11, DLSD12, DLSD16, and DLSD17, this figure shows the installation of Mounting Brackets (3) with Screws (4).

Figure 7: For DLSD7, DLSD8, DLSD9, and DLSD17, this figure shows aligning the Prong Assembly (7) with the bottom of the mounting brackets and securing with Screws (5).

Figure 8: This figure is used for multiple DLSD models. For DLSD1, DLSD2, DLSD5, DLSD10, DLSD11, DLSD12, and DLSD16, it shows positioning the Diffuser (2) over the Mounting Brackets (3) and securing with Screws (5). For DLSD7, DLSD8, DLSD9, and DLSD17, it shows positioning the Diffuser (2) in the grooves on the prong assembly and securing with Screws (5).

Figure 9: For DLSD13, DLSD14, and DLSD15, this figure illustrates installing Screws (11) into the Mounting Bracket (3) and then attaching the Mounting Bracket to the housing with Screws (4).

Figure 10: For DLSD6, this figure shows aligning the Diffuser (2) with screws on the bracket and securing with Thumb Nuts (6).

Troubleshooting Guide

If this fixture fails to operate properly, use the guide below to diagnose and correct the problem:

• Verify that the fixture is wired properly.
• Verify that the fixture is grounded correctly.
• Verify that the line voltage at the fixture is correct.
• Turn the ballast clockwise and verify it is seated correctly in the ballast socket.

Cleaning and Maintenance

To clean, wipe the fixture with a soft cloth. Clean the glass shade with mild soap and water. Do not use abrasive materials such as scouring pads or powders, steel wool, or abrasive paper.

Support and Replacement Parts

If further assistance is required, contact Technical Support at: (800) 748-5070

For availability of replacement parts, contact Technical Support or visit: lightahome.com