VIVO Instruction Manual

WARNING!

If you do not understand these directions, or if you have any doubts about the safety of the installation, please call a qualified technician. Check carefully to make sure there are no missing or defective parts. Improper installation may cause damage or serious injury. Do not use this product for any purpose that is not explicitly specified in this manual. Do not exceed weight capacity. VIVO cannot be liable for damage or injury caused by improper mounting, incorrect assembly or inappropriate use.

! WARNING: CHOKING HAZARD

SMALL PARTS - NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.

PACKAGE CONTENTS

NOTE: SOME HARDWARE MAY NOT BE USED

TOOLS NEEDED

• ? Phillips Screwdriver
• ? Wrench

DO NOT EXCEED WEIGHT CAPACITY.

⚖️ 2.2 lbs (1 kg)

Failure to do so may result in serious injury.

ASSEMBLY STEPS

STEP 1 (Option A): 28mm-45mm Diameter Poles

Loosen the bolts on Arm (A) using 6mm Allen Wrench (T-A) and slide onto the pole.

Diagram Description: Shows VIVO Arm (A) being attached to a pole with diameter between 28mm and 45mm. A 6mm Allen Wrench (T-A) is used to loosen bolts.

Tighten bolts using 6mm Allen Wrench (T-A). Apply Cable Clip (G) to Arm (A).

Diagram Description: Shows the Arm (A) secured to the pole. A Cable Clip (G) is being attached to the Arm (A) using the 6mm Allen Wrench (T-A).

STEP 1 (Option B): 46mm-60mm Diameter Poles

For pole sizes larger than 45mm, swap pre-installed bolts (A1) with M8x70mm Screws (S-D) using 6mm Allen Wrench (T-A) and slide Arm (A) onto the pole.

Diagram Description: Shows pre-installed bolts (A1) on Arm (A) being replaced with M8x70mm Screws (S-D) using a 6mm Allen Wrench (T-A) for poles with diameter between 46mm and 60mm.

Tighten M8x70mm Screws (S-D) using 6mm Allen Wrench (T-A). Apply Cable Clip (G) to Arm (A).

Diagram Description: Shows the Arm (A) secured to the pole with M8x70mm Screws (S-D). A Cable Clip (G) is being attached to the Arm (A).

STEP 2

Attach Left Tray (C) and Right Tray (B) with Connecting Plate (D) using M4x8mm Screws (S-A) and a Phillips screwdriver.

Diagram Description: Shows Left Tray (C) and Right Tray (B) being connected to the Connecting Plate (D) using four M4x8mm Screws (S-A) and a Phillips screwdriver.

STEP 3

Attach Tray Assembly to Arm (A) using M4x12mm Screws (S-B), M4 Nuts (S-C), Wrench (T-B), and a Phillips screwdriver.

Diagram Description: Shows the assembled tray unit being attached to Arm (A) using four M4x12mm Screws (S-B), four M4 Nuts (S-C), a Wrench (T-B), and a Phillips screwdriver.

STEP 4

Remove protective film from Wrist Pad (F) and place onto the front of the tray assembly. Place Mouse Pad (E) onto the tray assembly.

Diagram Description: Shows the Wrist Pad (F) with protective film removed being placed on the front of the tray assembly, followed by the Mouse Pad (E) being placed on the tray.

STEP 5

Adjust the tilt joint with 6mm Allen Wrench (T-A). Route cables through Cable Clip (G), and adjust as desired.

Diagram Description: Shows the tilt joint of the mount being adjusted using the 6mm Allen Wrench (T-A). Cables are routed through the Cable Clip (G). Adjustment ranges are indicated: ±90° for swivel, ±180° for rotation, +5°/-20° for tilt, and ±75° for arm pivot.

Support and Contact Information

Love your new VIVO setup and want to share? Tag us in your photo! @vivo_us

LAST UPDATED: 11/17/2022 REV1

Open Monday - Friday 7:00am - 7:00pm CST. Our dedicated support team can offer immediate assistance with rapid response times. If any parts are received damaged or defective, please contact us. We are happy to replace parts to ensure you have a fully functioning product.

? 309-278-5303 | AVG. RESOLUTION TIME (within office hrs): 5M 4S

? www.vivo-us.com (Chat live with an agent!) | AVG. RESOLUTION TIME (within office hrs): < 15 M

? help@vivo-us.com | AVG. RESPONSE TIME (within office hrs): 1HR 8M

• 23% within < 15m
• 38% within < 30m
• 61% within < 1hr
• 83% within < 2hr
• 92% within < 3hr

FOR MORE VIVO PRODUCTS, CHECK OUT OUR WEBSITE AT: www.vivo-us.com