VIVO Clamp-on Keyboard Tray for Corner Desk

SKU: MOUNT-KB10C

Scan the QR code with your mobile device or follow the link for helpful videos and specifications related to this product: https://vivo-us.com/products/mount-kb10c

GET IN TOUCH | Monday-Friday from 7:00am-7:00pm CST

• Email: help@vivo-us.com
• Website: www.vivo-us.com (Chat live with an agent!)
• Phone: 309-278-5303

WARNING!

If you do not understand these directions, or if you have any doubts about the safety of the installation, please call a qualified technician. Check carefully to make sure there are no missing or defective parts. Improper installation may cause damage or serious injury. Do not use this product for any purpose that is not explicitly specified in this manual. Do not exceed weight capacity. VIVO cannot be liable for damage or injury caused by improper mounting, incorrect assembly or inappropriate use.

WARNING: CHOKING HAZARD

SMALL PARTS - NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.

PACKAGE CONTENTS

• A (x2) Keyboard Tray
• B (x2) Sliding Rails
• C (x1) Baffle
• D (x2) Support Plates
• E (x2) Clamps
• F (x2) Clamp Pads
• S-A (x12) M5x12mm Flathead Screw
• S-B (x8) M4x7mm Screw
• S-C (x8) M5x12mm Screw
• T-A (x1) Wrench

TOOLS NEEDED

• Phillips Screwdriver

NOTE: SOME HARDWARE INCLUDED MAY NOT BE USED

DO NOT EXCEED WEIGHT CAPACITY. Failure to do so may result in serious injury. Maximum weight capacity: 11lbs (5kg)

ASSEMBLY STEPS

STEP 1

Attach Sliding Rails (B) to Keyboard tray (A) using M5x12mm Screws (S-C) and a Phillips screwdriver. Attach Baffle (C), and Supporting Plates (D) to Keyboard Tray (A) using M5x12mm Flathead Screws (S-A) and a Phillips screwdriver.

Diagram Description: Shows the keyboard tray (A) with sliding rails (B) attached to the sides. The baffle (C) and support plates (D) are also shown attached to the underside of the tray. Screws (S-C) and (S-A) are indicated for these connections.

STEP 2

Install Clamp Pads (F) to Clamps (E), then attach Clamps (E) to Sliding Rails (B) using M4x7mm Screws (S-B) and a Phillips screwdriver.

Diagram Description: Shows the clamp pads (F) being attached to the clamps (E). The clamps (E) are then shown being attached to the sliding rails (B) using screws (S-B).

STEP 3

Use Wrench (T-A) to adjust Clamps (E) to the desired angle. Place keyboard tray in desired location so that Clamp faces are flush with the desktop and tighten clamps.

Diagram Description: Illustrates a corner desk. The keyboard tray assembly is shown being attached to the edge of the desk using the clamps (E). A wrench (T-A) is shown being used to tighten the clamps.

Love your new VIVO setup and want to share? Tag us in your photo! @vivo_us

LAST UPDATED: 08/07/2023 REV1

Open Monday - Friday 7:00am - 7:00pm CST, our dedicated support team can offer immediate assistance with rapid response times. If any parts are received damaged or defective, please contact VIVO. We are happy to replace parts to ensure you have a fully functioning product.

Contact Information:

• Phone: 309-278-5303
• Average Resolution Time (within office hrs): 5M 4S
• Website: www.vivo-us.com
• Average Resolution Time (within office hrs): < 15 M
• Chat live with an agent!
• Email: help@vivo-us.com
• Average Response Time (within office hrs): 1HR 8M (23% within < 15m, 38% within < 30m, 61% within < 1hr, 83% within < 2hr, 92% within < 3hr)

FOR MORE VIVO PRODUCTS, CHECK OUT OUR WEBSITE AT: www.vivo-us.com