What's in the Box
| Part | Description | Quantity |
|---|---|---|
| 1 | Base | x1 |
| 2 | Pole | x1 |
| 3 | Lower Pole | x1 |
| 4 | Upper Pole | x1 |
| 5 | TV Mount Bracket | x1 |
| 6 | Support Arm | x1 |
| 7 | Cable Management Clips | x4 |
| 8 | Base Cover | x1 |
Hardware Included
Assembly Screws
| Label | Type | Quantity |
|---|---|---|
| A | M8x20 | x4 |
| B | M6x6 | x2 |
| C | M6x12 | x4 |
| D | M8x50 | x1 |
| E | M6x14 | x1 |
| F | M8x30 | x1 |
Allen Keys
| Size | Quantity |
|---|---|
| 5mm | x1 |
| 4mm | x1 |
| 2.5mm | x1 |
TV Mounting Screws & Washers
Select appropriate screws (M-A to M-G) and washers (M-H to M-J) based on your TV model. The diagrams show different screw lengths and washer types for compatibility.
| Label | Type | Quantity |
|---|---|---|
| M-A | M4x14 | x4 |
| M-B | M4x30 | x4 |
| M-C | M5x14 | x4 |
| M-D | M6x14 | x4 |
| M-E | M6x30 | x4 |
| M-F | M8x30 | x4 |
| M-G | M8x50 | x4 |
| M-H | Flat Washer | x4 |
| M-I | Spacer/Thick Washer | x8 |
| M-J | Spacer/Thick Washer | x8 |
Easy to Install
Step 1: Assemble Base and Pole
Connect the Lower Pole (Part 3) to the Base (Part 8) using the appropriate screws (diagram suggests D or A). Then, attach the main Pole (Part 2) to the Lower Pole (Part 3) using the Support Arm (Part 6) and screws (diagram suggests B).
Step 2: Attach TV Mount Bracket
Attach the Support Arm (Part 6) to the Pole (Part 2). Subsequently, connect the TV Mount Bracket (Part 5) to the Support Arm (Part 6). Pay attention to the orientation as shown in the diagram.
Step 3: Prepare TV for Mounting
Choose the correct screws (M-A through M-G) and washers (M-H through M-J) that match your TV's VESA mounting holes.
- Method A1 (Flat TV Back): Use screws directly without washers if your TV back is flat.
- Method A2 (Uneven TV Back): Use washers (M-H, M-I, M-J) for uneven TV backs. Stack washers as needed for a secure fit.
Important: Do not overtighten the screws when attaching the plate to the TV.
Distinguish front:
- 区分正面 (Chinese)
- 正面を区別する (Japanese)
- Distinguer devant (French)
- Vorderseite unterscheiden (German)
- Distinguere davanti (Italian)
- Distinguir frente (Spanish)
Step 4: Mount TV Assembly to Stand
Attach the Upper Pole (Part 4) to the main Pole (Part 2). Carefully lift the TV with the attached mounting plate and slide it onto the stand's pole assembly. Ensure it is fully seated.
Step 5: Secure TV Mount
Secure the TV Mount Bracket (Part 5) to the stand's pole assembly using the provided screws (diagram suggests C or E). Verify the TV is stable.
Step 6: Cable Management
Organize your TV cables by routing them along the stand's pole using the included Cable Management Clips (Part 7). This helps maintain a clean appearance.
Step 7: Final Adjustments
Adjust the TV's tilt angle up to ±15 degrees and rotate it up to 90 degrees as desired. The stand is designed for easy repositioning with "Move" and "Brake" functions.
