SuperATV Installation Instructions

Product Overview and Components

This document provides installation instructions for the SuperATV Glass Windshield designed for the Can-Am Maverick Trail. Before beginning, read all instructions and view illustrations.

Included Components:

• Windshield
• 2x - Clamp
• 4x - Knob
• 2x - Bracket
• Gasket
• Vent Cover - R
• Vent Cover - L
• 90° Bulb Seal
• Wiper Assembly (Handle, Wiper Blade, Washer, Nut, Grommet)

Liability Statement

SuperATV® products are designed for stock conditions. Modifying or fabricating parts may void the warranty. SuperATV® is not responsible for damage or injury resulting from improper installation, misuse, or modification. Users must comply with all local, state, and federal laws regarding vehicle operation and modifications. SuperATV® is not liable for any damages, losses, or causes of action exceeding the purchase price of the product. Warranty covers only SuperATV® parts; issues with OEM or other manufacturers' components are not covered. Users assume all responsibility for legal compliance and vehicle capability limitations.

Installation Steps

Step 1: Prepare the Vehicle

Remove roof hardware and carefully space the roof away from the frame to allow access.

[Image: UTV roof with hardware removed, indicating to space away from the frame.]

Separate the components of the wiper assembly (Wiper, Washer, Nut, Grommet, Handle) and set them aside.

[Image: Diagram showing separate components of the wiper assembly: Wiper, Washer, Nut, Grommet, Handle.]

Step 2: Prepare the Windshield Frame

Install the 90° Bulb Seal around the perimeter of the windshield frame. For easier installation and increased flexibility, soak the seal in hot water before cutting or installing.

[Image: Windshield frame with an arrow pointing to install the 90° Bulb Seal around the frame. Text advises soaking the seal in hot water for flexibility.]

Install the Gasket across the top of the windshield frame.

[Image: Gasket being installed across the top of the windshield frame.]

Step 3: Attach Brackets

When assembling, do not tighten hardware completely unless noted.

Install the Brackets to the windshield frame using the provided hardware: M6 x 20mm bolts, Sealing Washers, and M6 Nuts. Ensure correct orientation for the driver's side bracket.

[Image: Diagram showing the installation of brackets to the windshield frame using M6 x 20mm bolts, sealing washers, and M6 nuts. Close-up shows hardware details.]

Step 4: Install Vent Covers

Install the Vent Cover - L and Vent Cover - R onto the windshield frame. Secure them using the 4 Knobs.

[Image: Diagram showing the installation of Vent Cover - L and Vent Cover - R to the windshield frame, secured with 4 knobs.]

Step 5: Reinstall Wiper Components

Install the previously removed Wiper components (Grommet, Washer, Nut) onto the frame.

[Image: Image showing previously removed wiper components (Grommet, Washer, Nut) being installed onto the frame.]

Step 6: Install Wiper and Handle

Install the Wiper blade and Handle onto the frame.

[Image: Diagram showing the installation of the Wiper and Handle onto the frame.]

Step 7: Secure Clamps

Secure the Clamps around the vehicle's cage, to the windshield frame, and to the installed bracket. Use the M8 x 14mm hardware, including M8 Flat washers and M8 Lock nuts.

[Image: Diagram showing the clamp being secured around the cage, to the windshield frame, and to the bracket using M8 x 14mm hardware (M8 Flat, M8 Lock).]

Repeat this process for the opposite side of the vehicle.

Step 8: Final Attachment and Tightening

Secure the windshield assembly to the vehicle's frame using the remaining hardware: 2x M6 x 20mm bolts, 2x Sealing Washers, and 2x M6 Nuts. Re-secure the roof to the vehicle.

[Image: Image showing the windshield secured to the frame and roof using M6 x 20mm bolts, sealing washers, and M6 nuts (2 each). Text indicates to tighten all hardware completely.]

Final Check: Tighten all hardware completely.