Appendix F: Wiring Diagrams

Applicable UL Standards

• UL File No. S4019
• UL1610 Central-Station Burglar Alarm Units
• UL609 Local Burglar Alarm Units and Systems
• UL365 Police Station Connected Burglar Alarm Units & Systems
• UL985 Household Fire Warning System Units
• UL1023 Household Burglar Alarm System Units
• UL1635 Digital Alarm Communicator System Units
• UL1637 Home Health Care Signaling Equipment
• ANSI/SIA CP-01-2010

SIA-FAR Minimum System Requirements

• 1 HS2016/2032/2064/2128 Panel
• 2 Local annunciation devices (keypads such as HS2LCD, HS2LCDP, HS2ICN, HS2ICNP, HS2LED)

WARNING

Incorrect connections may result in PTC failure or improper operation. Inspect wiring and ensure connections are correct before applying power. Do not route any wiring over circuit boards. Maintain at least 25.4mm (1") separation.

WARNING

High voltage. Disconnect AC power and telephone lines prior to servicing.

System Wiring Overview

The wiring diagram illustrates connections for the DSC HS2016, HS2032, HS2064, and HS2128 alarm control panels.

Power Supply

A 16.5VAC/40VA Class 2 Transformer (Model DSC PTD1640U) connects to the 120VAC/60Hz primary. Note: Do not connect the transformer to a receptacle controlled by a switch.

Battery Backup

A 12V 7Ah or 12V 4.0Ah/7Ah battery connects to the BAT+ and BAT- terminals. The maximum battery charge current is 400mA. For 4-hour standby, a minimum 4Ah battery is required (Max. Aux current must not exceed 700mA). For 24-hour standby, a 14Ah battery is required (Max. Aux current must not exceed 470mA). Recommended batteries: DSC BD4-12 or DSC BD7-12.

Auxiliary Power and Keybus

AUX Wiring: Use No. 14-22 AWG conductor. AUX+ and Keybus (RED) are internally connected. The total current draw from keypads, PGM Outputs, and AUX circuits must not exceed 700mA. The CORBUS connects to additional keypads and expansion modules.

PGM Connections

PGM outputs have specific current limits: PGM1 (50mA max), PGM2 (300mA max), PGM3 (50mA max), PGM4 (50mA max).

Bell/Siren Output

Rated for 700mA (max). Observe polarity.

Ground Connection

A ground wire from the building electrical installation connects to the cabinet via a nut, lock washer, and star washer to ensure a good connection.

Telephone Connection

An RJ-31X telephone plug (26 AWG) is used.

Detector Wiring

2-Wire Smoke Detectors

• Compatibility Identifier: HS2-1
• Maximum Operating Voltage: 13.8V
• Maximum Circuit Resistance: 240 ohm (total)
• Maximum Number of Detectors: 18
• Model examples: FSA-210B Series (FS200 compatibility ID).
• Requires an End-of-Line Resistor (EOLR-3, 2200 ohm, 5%).

Note: Do not combine different models on the same circuit as operation may be impaired. Refer to the FSA-210 Installation Manual for more details.

4-Wire Smoke Detectors

• Smoke detector must be latching type (e.g., PG4926 Series).
• To reset smoke detector, enter [*][7][2].
• Connections include a power loop (12 VDC, 35mA max) and a supervisory relay.
• Requires an End-of-Line Resistor (EOLR-2, 2200 ohm, 5%).

Note: Refer to Installation Manual & Smoke Detector Instruction Sheet when locating detectors.

Typical Zone Circuits

The diagram shows four typical zone circuit configurations using End-of-Line Resistors (5600 ohm):

1. Normally Closed contact with End-of-Line Resistor.
2. Normally Open contact with End-of-Line Resistor.
3. One Normally Open contact and one Normally Closed contact with End-of-Line Resistor.
4. Two Normally Open contacts and two Normally Closed contacts with End-of-Line Resistor.

General Notes and Compliance

Power Limited Wiring: All wiring is power limited/Class II power limited, except for battery leads. Maintain at least 6.4mm (1/4") separation between power-limited and non-power-limited wiring and connections.

Installation Compliance: This equipment should be installed in accordance with the National Fire Code ANSI/NFPA 72 (National Fire Protection Association). For compliance with UL-985, at least one smoke detector is required.

FCC Compliance: This device complies with Parts 15 and 68 of the FCC rules. Operation is subject to the following 2 conditions: [1] this device may not cause harmful interference and [2] this device must accept any interference received, including interference that may cause undesired operation.

• Model: HS2128
• FCC Reg. No.: F53AL01BPHS2128
• REN = 0.1B
• Plug Type: RJ-31X
• Made in Canada.

Environmental: Temperature Range: 0°C-49°C [32°F-120°F]. Maximum Humidity: 93% RH.

NEC Compliance: The HS2016/2032/2064/2128 is UL Listed for limited energy installations per NEC Article 760. Recognized limited energy cable should be used. Observe NEC wiring requirements and local codes.

Detection Device Power: Security detection devices requiring power from the control panel must be UL Listed for the intended application and operate over the range of 11.6-12.6VDC (residential), 12.0VDC (commercial).

Recommended Motion Detectors: PG9904(P), PG9934(P), and PG9974(P) are recommended UL Listed motion detectors.

Compatible System Keypads: HS2LCDRF(4)(8)(9), HS2LCDRFP(4)(8)(9), HS2ICNRF(4)(8)(9), HS2ICNRFP(4)(8)(9), HS2LCD, HS2LCDP, HS2ICN, HS2ICNP, HS2LED.

UL Installation Suitability: Control panel is suitable for the following UL installations:

1. Grade AA Central Station and Grade AA Police Connect with high line security (using T-LINK to communicate to the Sur-Gard MLR-IP Receiver).
2. Household Fire and Grade A Household Burglary and Home Health Care Signaling Equipment.
3. Grade A Local / Grade B Central Station and Police Connect with basic line security.
4. Grade C Central Station. Refer to Installation Manual.

ULC NOTES:

• For ULC Listed Fire Monitoring Installations & module requirements, please refer to the ULC Installation Information Sheet, part #29002157.
• Use a CSA/cUL transformer, hardwired.
• All tamper circuits may be connected to the same zone.
• Use ULC-LA for AC Power indication.

NOTE: For ULC installations, please refer to the ULC Installation Information Sheet part#29002157.