PILSKOTT LED Pendant Lamp

Step 1 (Page 5)

Attach the lower decorative bar to the main housing. Insert the bar into the designated slots.

(Diagram shows a curved bar being attached to the bottom of the main light fixture housing.)

Step 2 (Page 6)

Secure a component within the main housing using two screws.

(Diagram shows a part being inserted and then fastened with two screws using a screwdriver.)

Step 3 (Page 7)

Insert the main control module into its designated slot within the lamp housing. Push it upwards until it is seated.

(Diagram shows a rectangular electronic module being inserted into a cavity in the lamp housing.)

Step 4 (Pages 8 & 10)

Mount the suspension bracket to the ceiling. Use appropriate fasteners for your ceiling type. Ensure it is securely attached. ⚠️ Do not use the type of screw shown with a cross mark [❌].

(Diagrams show the suspension bracket being positioned on a ceiling, screws being inserted and tightened. One diagram shows an incorrect screw type crossed out.)

Step 5 (Pages 9 & 12)

Attach the main lamp body to the suspension points. Ensure the mounting clips engage securely.

(Diagrams show the main lamp body being lifted towards the suspension bracket and clips being engaged.)

Step 6 (Page 10)

Prepare the power wires. Strip approximately 10 mm (25/64") of insulation from the ends of the wires.

(Diagram shows wire ends with insulation stripped to a specific length.)

Step 7 (Page 11)

Identify the Neutral (N) and Live (L) wires. The diagram shows terminal block markings for N and L.

(Diagram shows terminal block labels N and L, and corresponding wire connections.)

Step 8 (Page 14)

Attach a cover plate using four screws.

(Diagram shows a cover plate being placed and fastened with four screws.)

Step 9 (Page 14)

Attach another cover plate using two screws.

(Diagram shows a different cover plate being placed and fastened with two screws.)

Step 10 (Page 15)

Connect the main power cable. Insert the cable into the housing and ensure the cover clicks shut.

(Diagram shows a power cable being inserted into an opening and a cover being closed until it clicks.)

Step 11 (Page 16)

Connect the power wires to the terminal block. Connect the Neutral (N) wire to the N terminal and the Live (L) wire to the L terminal. Ensure wires are fully inserted.

(Diagrams show wires being pushed into push-in terminal connectors, with N and L markings visible.)

Step 12 (Page 17)

Secure an internal component or cover plate using two screws.

(Diagram shows a component being placed and fastened with two screws.)

Step 13 (Page 17)

Attach the final cover plate using four screws.

(Diagram shows a cover plate being placed and fastened with four screws.)

Step 14 (Page 18)

Connect the main power cable and ensure the cover clicks shut.

(Diagram shows a cable being inserted into an opening and a cover being closed until it clicks.)

Step 15 (Page 19)

Adjust the suspension wires to the desired height. Secure the wires by tightening the locking mechanism.

(Diagrams show adjusting the length of suspension wires and then tightening a screw or mechanism to lock them.)

Step 16 (Page 22)

Attach the main lamp body to the suspension mounts. Ensure it clicks into place.

(Diagrams show the lamp body being connected to the ceiling mounts, with an emphasis on the locking mechanism engaging.)

Smart Functionality & Pairing (Page 23)

ℹ️ To pair the luminaire with a remote control or the IKEA Home smart app:

1. Ensure the luminaire is powered on.
2. On the remote control or in the app, initiate the pairing process.
3. Press and hold the pairing button on the remote control for more than 10 seconds, or follow app instructions.

(Diagrams show a remote control with a pairing button and a luminaire with a reset button/hole.)

Resetting the Luminaire (Page 23)

ℹ️ To reset the luminaire to factory settings:

1. Ensure the luminaire is powered on.
2. Locate the reset button (often a small hole, indicated by 'Reset').
3. Press and hold the reset button for more than 10 seconds.

(Diagram shows a reset button on the luminaire.)