Haloview Byte Tango System

1 Precautions

Storage

1. Do not expose the monitor to extreme heat, cold, or sudden temperature changes. The storage temperature of this device is -30 to +80°C (-22 to +176°F). The operating temperature is -20 to +70°C (-4 to 158°F) with humidity under RH90%.
2. Never use this device in environments with excessive moisture, dust, or smoke.
3. Avoid dropping or striking this device.
4. Never puncture, scratch, or use abrasive cleaning materials on this device.
5. Leave at least a 2" space between the monitor and walls, cabinets, or other objects to allow adequate air circulation around the device.
6. The monitor is not designed to be waterproof.

Operating Precautions

1. The device can be powered by DC 10-32V or USB Type-C 5V/2A.
2. Improper cable connections may damage the monitor. Remove the power cable connections when you do not intend to use the device.

⚠️ Warning

1. High voltage is present within the monitor. The opening of the case should be done by professionals.
2. Do not watch the video while driving unless you are monitoring the rear view camera display.

❗ Special Notice

Occasionally, a few highlights or dark spots may occur on the LCD screen. This is a very common phenomenon in active matrix display technology and doesn't necessarily indicate any defects or faults. Never try to repair this device by yourself. In case of any problems, please turn off the display at once and notify the company or authorized dealer. The monitor is a complex device. Any disassembly or modification may lead to damage and void the warranty.

Maintenance

1. Remove all cable connections from the monitor before cleaning the device.
2. Use a mild household detergent and clean the unit with a slightly damp, soft cloth. Never use strong solvents such as thinner or benzine, as they might damage the finish of the device.

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

⚠️ This symbol is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute risk of electric shock to persons.

⚠️ This symbol is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.

FCC WARNING

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.

If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

To maintain compliance with FCC's RF Exposure guidelines, this equipment should be installed and operated with a minimum distance between 20cm and your body: Use only the supplied antenna.

2 Accessories

The product is under continuous improvement and the specifications will change without notice. Picture for reference only. Please refer to the actual product and accessories. The antennas of BT6 solar are shorter than BT7 solar; please refer to the actual product received.

❗ Special Notice: Accessories supplied in kit may be different for each application.

3 Features

• Upgraded touch screen for easy operation.
• NORMAL, MIRROR, FLIP and MIR-FLIP viewing available.
• Split mode auto-scan mode and single-display mode available.
• Support 4-channel composite and single-channel recording in AVI signal format.
• Auto dim function available.
• 4 wireless camera inputs.
• Video input: 1080P.
• Wide voltage input: DC10-32V or USB Type-C 5V.
• Camera night LED can be turned ON/OFF via monitor.
• The monitor turns on and the camera wakes up automatically.
• The camera turns off automatically one minute after the monitor turns off.

4 Specifications

Monitor

Camera

5 Functions of each part

Monitor:

• PAIR button: Used for pairing the camera.
• Light Sensor: Adjusts screen brightness automatically.
• Micro SD Card Slot: For recording video files.
• Power button: Turns the monitor on/off.
• USB Type-C: Power input.
• DC: Power input.
• Power Indicator: Turns red when the monitor is powered on. Turns green when the monitor is working normally.
• Speaker: Outputs audio.

6 Basic Operation

Installation of Suction Cup Mount

1. Adjust monitor height by sliding the monitor up or down in the slot, then tighten the knob.
2. Adjust monitor angle by loosening the lower knob on the suction cup mount, tilting the monitor to the desired angle, and re-tightening the knob.

Installation of 3M Mount

Follow these steps for installing the 3M mount:

1. Clean the surface where you plan to install the mount using the provided alcohol wipes.
2. Remove the base from the mount and paste the base onto the cleaned surface.
3. Press the adhesive base firmly for 15 seconds when pasting. The base needs to stand for 12-24 hours before hanging the monitor.
4. Attach the mount to the base.

This multi-purpose multi-angle adjustment display mount can be used in various positions, such as mounted on the windshield or dashboard.

Please put a static sticker on the windshield before mounting the bracket on the front windshield.

7 Battery-Operated Camera and Solar Panel

Power Button

• Short Press Power Button: In non-charging status, turns the entire camera (camera itself and battery) ON/OFF. In charging status, turns the camera itself ON/OFF (the battery will continue charging or discharging).
• Press Power Button for 5 Seconds: When the device is powered on, pressing the power button for 5 seconds causes two indicator lights to blink simultaneously, entering remote control pairing mode (remote control needs to be purchased additionally).
• Press Power Button for 20 Seconds: When the device is powered on, pressing the power button for 20 seconds until all indicator lights turn off puts the device into deep sleep mode. A short press of the power button will awaken the camera.

Pairing

Two methods for pairing:

1. Method 1: Press the [PAIR button] on the monitor first ➡️, and then press the [PAIR button] on the camera (the camera is turned on). After successful pairing, the monitor will display the image captured by the camera.
2. Method 2: Press the [PAIR button] on the monitor first ➡️, and then press the [Power button] on the camera (the camera is turned off). After successful pairing, the monitor will display the image captured by the camera.

Note: To realize remote power on/off, the camera must be paired on the channel of CAM4.

Automatic Standby

Unplug the charger when charging; the camera will automatically enter standby mode after 5 minutes. Under normal working conditions, if the monitor is turned off or the camera loses signal for over 1 minute, the camera will automatically enter standby mode.

Indicators

Charging and Discharging

8 Wiring Instruction

Camera and Solar Panel Wiring Method:

The camera connects to the solar panel using a magnetic mount. Ensure the magnetic part is attached to the metal plate for secure connection.

Monitor Wiring:

Connect the monitor to the cigarette lighter power adapter. Power the monitor through the vehicle's 12V cigarette lighter or USB Type-C.

For more cameras, extra cameras can be paired separately to CAM1/CAM2/CAM3/CAM4. Please refer to page 18 PAIRING.

Solar Panel Extension Cord: If the solar panel is mounted close to the camera, it can be used without connecting the solar panel extension cord.

9 Installation

Please find best signal reception position before installation

The metal body of the vehicle can attenuate wireless signal strength sharply. It is necessary to test the signal strength before installation.

1. Connect Monitor and Camera: Connect the monitor and camera as shown in the diagrams.

2. Pairing the Camera: Pair the camera to the monitor. Refer to page 19 PAIRING. 4 cameras can be paired separately to CAM1/CAM2/CAM3/CAM4.

3. Test Signal Strength: Place the monitor and the camera at the intended position to test signal strength.

Signal Strength Indicators:

• Good signal: Display shows strong signal bars.
• Poor signal: Display shows weak signal bars.

If the signal strength of the planned installation position is under 2 bars, please change to another position, or mount the camera higher to ensure the antenna is at the highest point without being blocked. Refer to the following pictures for guidance.

Installation Position 1:

Mount the camera higher than your vehicle's roof, keeping the antenna vertical.

Installation Position 2:

Mount the camera lower but as close as possible to the vehicle's roof, and move the antenna outward 15-30 degrees. The antennas' proximity to any metal surfaces on the vehicle may affect signal strength.

❗ Special Notice: After position adjustment, you can start installation if your signal strength is still above 2 bars.

Image freezing may occur when the vehicle is 42-65ft long and the antenna is mounted in a poor location (the antenna is not placed on the roof of the vehicle or there is obstruction around the antenna). In this case, it is recommended to purchase the Haloview 10M or 12M antenna extension cable and place it on the roof without any obstacles.

Antenna Placement Advice:

• It is recommended to choose an antenna length that is 2-3ft longer than the length of the RV.
• To achieve better signal, it is recommended to purchase the Haloview antenna extension cable and place it in front of the RV, near the roof, without any obstacles.

If you get poor signal reception, or signal cannot reach at least 2 bars, please keep the antennas perpendicular and adjust the angle of the antenna to find the best signal reception position.

10 Menu

Shortcut Menu

Tap the screen when in single image mode; it pops up the first group of shortcut MENU. You can easily switch to each of the four channels of cameras or go to Quad Mode. Tap [Main Menu icon] to go to Main MENU.

CH4 Settings:

• 120S: The camera automatically wakes up when the monitor is turned on, and the camera will be automatically turned off after 120 seconds.
• 240S: The camera automatically wakes up when the monitor is turned on, and the camera will be automatically turned off after 240 seconds.
• NEVER: The camera automatically wakes up when the monitor is turned on. The camera will continue to work and won't be turned off automatically. If NEVER is selected, the camera won't be turned off even when switching from CH4 to other CH. To turn off the camera in CH4, please tap [OFF].
• ON/OFF: Tap [ON/OFF] to easily turn the camera ON/OFF manually.

Notice: Even if NEVER is selected, if you turn off the monitor or the monitor loses signal with the camera for over 1 minute, the camera will automatically turn off.

Tap the screen again to pop up the second group of shortcut MENU.

Shortcut Menu Functions:

• Tap [Parking Line icon] to turn on/off parking line in the current channel of the camera. When the parking line is turned on, exit the shortcut menu to display the parking line.
• Tap [Volume icon] to turn on/off voice in the current channel of the camera.
• Tap [Brightness icon] to adjust the screen brightness.
• Tap [Night Light icon] to turn on/off the current camera night light. When the camera night light is turned on, the indicator will change.
• Tap [Record icon] to start recording or pause recording.
• Tap [SCAN icon] to automatically switch channels of cameras.

In quad mode (QMODE), an audio icon is highlighted in CH1 if that channel has audio active. Tap any of the audio icons to hear the audio of any channels of cameras.

Notice: Please tap the audio icon instead of other areas. Otherwise, the display will switch to the specific channel of the camera.

Press [Main Menu icon] to go to Main Menu.

Press [Exit icon] to exit.

10.1 MENU

The main menu provides access to various settings:

• VOLUME: Adjust audio volume.
• PAIRING: Manage camera pairing.
• PICTURE: Adjust brightness, contrast, and color.
• MIRROR: Set image mirroring (Normal, Mirror, Mir-flip, Flip).
• QMODE: Select display modes (Split, Triple, Quad).
• SETTING: Access system settings like Trigger, Video Format, Autodim, Screen Off.
• SCAN: Enable automatic channel switching.
• PARK-LINE: Adjust parking lines.
• RECORD: Configure recording settings.
• PLAY: Play back recorded video files.

10.2 VOLUME

Tap the [VOLUME icon] to access the VOLUME setting. Tap the bar to adjust volume. Tap [ON/OFF] to MUTE or UNMUTE the volume.

10.3 PAIRING

Cameras and the monitor are paired at the CAM4 channel as the factory default setting. When you open the box, power on the monitor and camera, tap the monitor to find the first group of shortcut Menu and tap CH4; the image will be displayed. Otherwise, please try the following methods for pairing:

Tap [Main Menu icon] to get access to Main Menu. Tap [PAIRING icon] to enter pairing status. You will have 50 seconds for pairing. Press the pairing button on the bottom of the camera until you hear a "tah". Video will be displayed after pairing is complete.

Quick Access to Pairing Status: Press the [PAIR button] for 3 seconds to enter pairing status.

If you press the pair button by mistake and the monitor enters the pairing status, you can tap [Exit icon] to exit the pairing status.

10.4 PICTURE

Tap [Main Menu icon] to get access to Main Menu. Tap [PICTURE icon] to enter Picture setting. Tap the bars to adjust BRIGHTNESS/CONTRAST/COLOR. Tap [ON/OFF] to turn on/off the current camera night LED light.

10.5 MIRROR

Tap [Main Menu icon] to get access to Main Menu. Tap [MIRROR icon] to enter MIRROR setting. Tap Normal/Mirror/Mir-flip/Flip at your will.

10.6 QMODE

Tap [Main Menu icon] to get access to Main Menu. Tap [QMODE icon] to enter QMODE setting. Tap any of the desired display modes (Split, Triple, Quad).

10.7 SETTING

Tap [Main Menu icon] to get access to Main Menu. Tap [SETTING icon] to enter SETTING.

• Tap [ON/OFF] to turn on/off Trigger.
• Tap [NTSC/PAL] to switch video format.
• Tap [ON/OFF] to turn on/off Autodim. When Autodim is turned on, the monitor will automatically decrease brightness in low light.
• Tap the bar from 0 to 45 to set screen off duration. If 0 is selected, the screen stays on. If 45 is selected, the display will turn off after 45 seconds of inactivity.

10.8 SCAN

Tap [Main Menu icon] to get access to Main Menu. Tap [SCAN icon] to enter SCAN setting. The SCAN function allows the monitor to automatically switch channels of cameras. In the shortcut menu, you can tap [SCAN icon] to start Scan or exit Scan. A Scan icon will appear on the display if the display enters scan mode.

10.9 Park Line Adjustment

Tap [Main Menu icon] to get access to Main Menu. Tap [PARK-LINE icon] to enter parking line setting. You can slide the screen to adjust the inclination and the width of the parking line.

Slide left/right to adjust park lines horizontally.

Slide up/down to adjust park lines vertically.

10.10 RECORD

Tap [Main Menu icon] to get access to Main Menu. Tap [RECORD icon] to enter RECORD setting.

Please insert TF card in TF card slot, max 256G Micro SD card.

Note: TF card must be formatted before using. Tap Format ON and Confirm Format. After TF card is formatted, a yellow folder icon will be shown on the screen, indicating TF card is available now.

When COVER is turned on, the overwrite function will be activated. Previously recorded video files will be overwritten when TF card memory is full.

Note: When in QUAD or SPLIT display, the monitor will record all displayed channels of CAM at the same time.

TIME Setting:

Tap Year/Month/Date/Hour/Minute/Second; it will pop up up/down arrows. Tap the arrows to adjust Year/Month/Date/Hour/Minute/Second.

10.11 PLAY

Tap [Main Menu icon] to get access to Main Menu. Tap [PLAY icon] to enter PLAY setting.

Tap [Select icon] to select, Tap [Up arrow] and [Down arrow] to move up or down.

Tap [Play icon] to play the selected file.

Read the SD card through PC; there will be two formats of files. It is suggested to play the AVI format file for higher video resolution.

10.12 Trigger Function

Tap [Main Menu icon] to get access to [SETTING]. The Trigger switch is off by default.

Tap [ON] to activate Trigger function. If the trigger switch is turned on, the yellow [SIGNAL icon] will appear on the display. To achieve trigger function, you also need to complete trigger wiring.

In Triggering status, MENU operation is invalid, and the screen prompts TRIGGER LOCK.

10 Troubleshooting

The symptoms described below do not necessarily mean a failure within the display. Please check the following items before you initiate a request for repair.