Haloview M7108 User Manual
2.4G Digital 720P 7" LCD Wireless Monitor
Please read all instructions carefully before using, and keep the manual for future reference.
V1.3
Contents
1. Precautions
Storage
- Do not expose the monitor to extreme heat, cold, or sudden temperature changes. The storage temperature of this device is -30 to +80°C or -22 to +176°F. The operating temperature is -20 to +70°C or -4 to 158°F with the humidity under RH90%.
- Never use this device in environments with excessive moisture, dust or smoke.
- Avoid dropping or striking this device.
- Never puncture, scratch or use abrasive cleaning materials on this device.
- Leave at least a 2" space between the monitor and walls, cabinets or other objects to allow adequate air circulation around the device.
- The monitor is not designed to be waterproof.
Operating Precautions
- The device can be powered by a 10 -32 volt automotive battery or vehicle electrical system.
- Improper cable connections may damage the monitor. Remove the power cable connections when you do not intend to use the device.
⚠️ Warning
- High voltage is present within the monitor. The opening of the case should be by professionals.
- Do not watch the video while driving unless you are monitoring the rear view camera display.
⚠️ Special Notice
Occasionally, a few highlights or dark spots may occur on the LCD screen. This is a very common phenomenon in active matrix display technology, and doesn't necessarily indicate any defects or faults. Never try to repair this device by yourself. In case of any problems, please turn off the display at once and notify our company or authorized dealer. The monitor is a complex device. Any disassembly or modification may lead to damage and void the warrantee.
Maintenance
- Remove all the cable connections from the monitor before cleaning the device.
- Use a mild household detergent and clean the unit with a slightly damp, soft cloth. Never use strong solvents such as thinner or benzine, as they might damage the finish of the device.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER(OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL
⚠️ This symbol is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute risk of electric shock to persons.
⚠️ This symbol is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.
Declaration of conformity
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
- This device may not cause harmful interference.
- This device must accept any interference received, including interference that may cause undesired operation.
[FCC Logo] [RED Logo]
2. Accessories
- U-Support Bracket X 1
- Center Mount Bracket X 1
- Sun Shield X 1
- User Manual X 1
- Angle Adjustment Screws X4
- Cigarette Lighter X1
- Camera conversion cable X1
- BMW connector adaptor X1
- Pairing Cable X1
Diagram showing the connection of cigarette lighter, pairing cable, camera or TX-box, and monitor.
Please pair the camera with the monitor by using external 12V power supply and provided Pairing Cable before installing this system on your RV.
⚠️ Special Notice
Accessories supplied in kit may be different for each application.
3. Features
- NORMAL, MIRROR, FLIP and MIR-FLIP viewing available.
- Split mode, auto-scan mode and single-display mode available.
- Auto pairing: Auto pairing happens when camera is activated.
- Support 4-channel composite and single-channel recording in AVI signal format.
- Auto dim function available.
- 4 wireless camera inputs.
- Video input: 720P.
- Wide voltage input: 10 - 32V.
4. Specifications
| LCD size | 7" 16:9 |
| Resolution | 1024 x 3 (RGB) x 600 |
| Contrast | 800:1 |
| Brightness | 500 cd/m² |
| Viewing Angle | U/D: 85, R/L: 85 |
| Aspect Ratio | 16:9 |
| Channel | 4 channels |
| Operating Frequency | 2400-2483.5 MHz |
| Receiving Sensitivity | -85 dBm |
| Video Compression | H.264 |
| Latency | 200ms |
| Transmitting Distance | 984ft line of sight |
| Micro-SD/TF Card | Max. 128G |
| Video Format | AVI |
| Power Supply | DC 10-32V |
| Power Consumption | Max. 8W |
| Loudspeaker | 1W/8Ω |
| Operating temperature | -20~+70°C, RH90% |
| Storage temperature | -30~+80°C, RH90% |
5. Functions of each part
Diagram of the Haloview monitor showing the front panel with labels for Digital Color LCD screen, Loudspeaker, Channel Selections, Brightness decrease, Menu, Brightness increase, Power switch, Power indicator, and Light level. It also indicates that the OK button can be used to enter menu item or save user settings, as a shortcut to start/stop recording, and for 3 seconds to enter Pairing.
Diagram of the back of the Haloview monitor showing the Micro-SD/TF Card Slot and Mounting bracket.
6. Basic Operation
1) Installation of Center Mounting Bracket:
- Adjust monitor height by sliding monitor up or down in slot, then tighten knob.
- Adjust monitor angle by loosening lower knob on center mounting bracket, tilting monitor to desired angle, and re-tighten knob.
Diagram illustrating the installation of the center mount bracket with labels for support attaching piece and knob.
2) Installation of U-support Bracket
Diagram illustrating the installation of the U-support bracket with labels for angle adjustment screws.
7. Wiring Instruction
Camera Wiring
Power on the camera by connecting the Red positive wire to 10 - 32 VDC power source, Black to Negative/Ground source, and connecting camera plug.
Diagram showing camera wiring with positive and negative terminals.
Monitor Wiring
Connect the monitor with BMW connector adaptor, connect the DC connector of BMW connector adaptor to cigarette lighter. Power the monitor by vehicle 12V through cigarette lighter.
Diagram showing monitor wiring through a cigarette lighter adapter.
For more cameras, extra cameras can be paired separately to CAM1/CAM2/CAM3/CAM4. Please refer to page 19 PAIRING.
8. Installation
Please find best signal reception position before installation
The metal body of the vehicle can attenuate wireless signal strength sharply. It is necessary to test the signal strength before installation.
① Please connect monitor and camera as below picture
Diagram showing monitor and camera connection.
② Pairing the camera to the monitor, please refer to page 20 PAIRING. 4 cameras can be paired separately to CAM1/CAM2/CAM3/CAM4.
③ Put the monitor and the camera at the intended position to test signal strength.
Diagrams showing "Good signal" and "Poor signal" on the monitor display.
If signal strength of the position that you planned to install a camera is under 3 bars, please change to another position, or mount the camera higher to make sure the antenna highest of the top without being blocked. Please refer to below pictures:
Diagrams illustrating correct and incorrect antenna placement for signal strength, including a 15-30 degree angle recommendation.
Installation Position 1:
Mount the camera higher than your vehicle's roof, keeping the antenna vertical.
Installation Position 2:
Mount the camera lower but as close as possible to vehicle's roof, and move the antenna outward 15-30 degree. The antennas proximity to any metal surfaces on the vehicle may affect signal strength.
⚠️ Special Notice
After position adjustment, you can start installation if your signal strength is still above 3 bars.
Installation
- Antennas should be vertically lined to the ground. Make sure there is no obstacle around antennas.
Diagrams showing correct and incorrect antenna placement on trucks.
- Magnet based extension antenna should be attached on the top of the vehicle. Make sure there is no obstacle around.
Diagrams showing correct and incorrect placement of magnet-based antennas on trucks.
Diagram showing a monitor with an antenna, with text indicating to adjust the antenna angle if poor signal reception occurs.
10. Troubleshooting
The symptoms described below do not necessarily mean a failure within the display. Please check the following items before you initiate request for repair.
| Symptoms | Possible Causes/Solutions |
| No picture | Improper connection of automobile adapter. Use of unauthorized power supply. Power switch is OFF. Please re-pairing the system. Refer to page 19 PAIRING. |
| No signal | Check whether the camera is powered on. Please check whether antennas are plugged on both monitor and camera. Please check the angle of the antenna. Please check whether metal obstacles near the antenna. Please re-pairing the system. Refer to page 19 PAIRING. |
| No sound | Check whether the sound volume is turned off or set too low. |
| Dark picture | Check whether brightness and contrast are adjusted correctly. |
| No color | Adjust the HUE settings. |
| Button invalid | All Button invalid when trigger wire is activated. Please deactivate trigger wire signal to get the button function valid. For example, you need to turn off LEFT TURN light or REVERSING light to deactivate trigger wire signal of CAM2 or CAM4. MENU button invalid in split display. If MENU button invalid, please check whether it is under split display. You need to switch to single display by pressing SEL button to get the MENU button valid. |
| Unable to record | Please check whether TF card inserted Please check whether TF card formatted before recording Please check whether TF card storage full |
The monitor is equipped with Anti-Glare screen. Please remove the screen protector to get best picture quality after installation.
Related Documents
 |
Haloview Byte Tango System BT7 Touch / BT6 Touch User Manual User manual for the Haloview Byte Tango System, covering the BT7 Touch and BT6 Touch models. Details features, specifications, installation, operation, and troubleshooting for this 2.4G Digital 1080P Touch Screen System. |