Enbrighten In-Wall Smart Switch

Product Overview

The Enbrighten In-Wall Smart Switch is designed for permanently installed fixtures and offers both manual and remote control via a Zigbee controller. It can be integrated into multiple groups and scenes, used in single-pole or multi-switch configurations (with compatible add-on switches), and features auto line/load detection. The switch includes interchangeable paddles (white and light almond), over-the-air updates, a blue LED indicator for location, and Zigbee 3.0 certification for seamless home automation. It also supports energy monitoring, reporting wattage (W) and kilowatt-hours (kWh) through the Zigbee controller interface.

Specifications

• Power: 120VAC, 60Hz
• Signal Frequency: 2.4GHz IEEE 802.15.4
• Maximum Loads: 960W incandescent, 1/2HP motor, or 1800W (15A) resistive
• Range: Up to 150ft (45.7m) line of sight
• Operating Temperature: 32-104° F (0-40° C)
• Usage: Indoor use only
• Wire Gauge: 14AWG or larger, suitable for at least 80° C

Installation Instructions

WARNING: SHOCK HAZARD. Ensure power to the circuit is OFF at the breaker or fuse box before proceeding. If unsure, consult a qualified electrician.

Tools Needed:

• Screwdriver
• Pliers

Single-Switch Wiring:

1. Shut off power to the circuit. Verify power is OFF.
2. Remove the wallplate and mounting screws.
3. Carefully remove the existing switch from the box without disconnecting wires.
4. Identify the wires: Ground (Green/Bare), Line/Load (Black), Neutral (White), and Traveler (Red/Other - for 3-way installations only).
5. Disconnect wires from the old switch and label them.
6. Match the switch terminals (A. Ground, B. Line/Load, C. Line/Load, D. Traveler, E. Neutral) to the corresponding wires.
7. Strip wire insulation to 5/8in. (16mm).
8. Connect the ground wire to the GROUND terminal.
9. Connect the load wire (to the light) to one LINE/LOAD terminal.
10. Connect the line wire (from the electrical panel) to the other LINE/LOAD terminal.
11. Connect the neutral wire to the NEUTRAL terminal (use jumper wire if needed).
12. Insert the switch into the box, being careful not to pinch wires.
13. Mount the switch independently in a vertical position.
14. Secure the switch with the supplied screws.
15. Mount the wallplate.
16. Restore power and test the system.

Changing Paddle Color (Optional):

1. Push side tabs to release the paddle. Lift the cover off.
2. Snap the new paddle into place.
3. Return to step 3 of the installation.

Multi-Switch Wiring:

For 3-way or 4-way installations, the Enbrighten add-on switch (12723/46199) is required. Do not connect the traveler terminal to a non-Enbrighten switch. Ensure add-on switches are correctly installed before applying power.

Basic Operation

• Manual Control: Press the top of the rocker to turn ON, press the bottom to turn OFF.
• Remote Control: Control the connected light via a Zigbee controller.

Zigbee Network Pairing

1. From your Zigbee controller, initiate the process to add a lighting device and enter pairing mode.
2. Restore power to the smart switch at the circuit breaker.
3. The LED status indicator will blink as the switch scans for a compatible network.
4. Once paired, the LED will stop blinking, and the switch will appear in your controller's menu.

Note: If pairing times out, press and release the front panel rocker to restart the process.

LED Indicator

The LED below the switch can function as a guide light or status indicator. Cycle through options by pressing the top of the rocker three times quickly, then the bottom once. Options include:

• LED ON when load is OFF (default guide light).
• LED ON when load is ON (indicates switch is ON).
• LED always OFF.

Resetting the Smart Switch (Remove from Zigbee Network)

• Via Zigbee Controller: Use your controller's interface to remove the smart switch.
• Manual Reset: Tap the top of the rocker (ON button) 10 times quickly.

Important Safety Information & Compliance

This device complies with Part 15 of the FCC and Industry Canada license-exempt RSS standards. Operation is subject to conditions that prevent harmful interference. Modifications are not permitted and can void the user's authority to operate the device. The switch is intended for use with copper wire only and must be installed in accordance with electrical codes. Do not use with medical or life-support equipment.

Warranty

Jasco Products Company warrants this product against manufacturing defects for five years from the original date of purchase. This warranty covers repair or replacement and does not extend to consequential damages. Contact Jasco Products Company for warranty service.

Support

For product support, accessories, and manuals, visit www.byjasco.com/support or contact Jasco Consumer Care at 1-800-654-8483.