PAX IM15 Unattended Payment Terminal

1. CONTENTS

Please make sure the following items are included with your IM15 unattended payment terminal. If any items are missing, contact your dealer.

• 1 x IM15 Unattended Payment Terminal
• 4 x M4 nuts
• 4 x M4 screws
• 1 x IM15 Mounting Bracket

2. PRODUCT DESCRIPTION

Figure 1: Front View

The front of the IM15 payment terminal features:

• 1. LCD touchscreen
• 2. Speaker
• 3. Proximity and light detector
• 4. LED status indicator
• 5. Camera flash LED
• 6. Camera lens

Figure 2: Back View

The back of the IM15 payment terminal includes the following ports and connectors:

• 1. Digital IO port
• 2. 4G antenna connector (Note: Does not include SIM card slot for configuration with only BT/WIFI/NFC or with only NFC)
• 3. MDB port
• 4. Status LED
• 5. USB Type-A port
• 6. Back cover
• 7. Reset button
• 8. USB Type-C port
• 9. RJ45 port (RS233)
• 10. RJ45 port (Ethernet)

Figure 3: View from All Sides

Diagrams showing the IM15 terminal from its front, back, and side profiles.

3. INSTALLATION

3.1 SIM Cards

For configurations with only BT/WIFI/NFC or with only NFC, a SIM card slot is not included.

Figure 4: Accessing SIM Card Slot

To access the SIM card slot:

1. Remove the back cover to reveal the 4G board.
2. Hold the antenna connector and pull the 4G board away from the body of the IM15.
3. Flip the 4G board over to access the SIM card slot.
4. Open the card slot and insert the SIM card with the contacts facing towards the 4G board and the clipped corner aligned with the slot.
5. Lock the mount with the card inside.

3.2 SAM Cards

Figure 5: SAM Card Slots

The two SAM card slots are visible when the back cover and 4G board are removed.

To install a SAM card:

1. Open the card slot.
2. Insert the SAM card into the slot with the contacts facing towards the IM15 and the clipped corner aligned with the slot.
3. Lock the mount with the card inside.

Note: Do not power on the IM15 while installing or removing SIM or SAM cards.

To reassemble the device: slot the 4G board into the board-to-board connector, aligning the four notches on the board with the four plastic tabs on the body of the IM15. Then, replace the back cover and screw it in place.

3.3 Device Dimensions

Figure 6: Device Dimensions (mm)

Technical drawings showing the dimensions of the IM15 terminal in millimeters, including front, side, and back views with measurements.

3.4 Device Installation

Figure 7: Device Installation

The installation process involves mounting the terminal using a bracket:

1. Ensure the back face of the installation area has four stud bolts corresponding to the mounting points on the mounting bracket. Slide the mounting bracket into place with the correct orientation and fix it with four M4 nuts.
2. Slide the IM15 unit into place with the orientation shown in the diagram. The back portion of the device should rest securely inside the mounting bracket.
3. Apply a torque of 0.6 to 0.8 Nm to each of the four M4 screws to secure the IM15 unit to its mounting bracket.

4. INSTRUCTIONS

4.1 Power On/Off

• Power On: Plug the IM15 into an appropriate power source (12 to 48 VDC) via the MDB port, the digital IO port, or the RS232 RJ45 port.
• Power Off: Disconnect the IM15 from the power source it is connected to.

4.2 Contactless Transactions

When the device is ready to accept a contactless transaction, the contactless icon will appear on screen. Orient the card or NFC device parallel to the screen and hold it at a distance of 4 cm or less directly above the contactless icon.

4.3 Code Scanner Transactions

When the device indicates on screen that it is ready to scan a 1D or 2D code, orient the code parallel to the code scanning camera and place it directly in front of the camera.

4.4 Environmental Conditions

• Storage Temperature: -30°C ~ 70°C (-22°F ~ 158°F)
• Operating Temperature: -20°C ~ 70°C (-3°F ~ 158°F)
• Relative Humidity: 5% ~ 95% (non-condensing)

5. MAINTENANCE AND USAGE

1. If any cables become damaged, seek a replacement.
2. Do not insert unknown materials into any port on the IM15, as this may cause serious damage to the device.
3. Only qualified personnel should repair this product.
4. The frequency range from 5150 to 5250MHz is for indoor use. During normal use, the IM15 surface should be kept clear of dirt and possible liquid contaminants.
5. While the IM15 is designed to resist ingress of dust and liquids, it is not designed to resist pressurized liquids such as water hoses. Keep the back of the device away from dust and liquids as much as possible.
6. Ensure that the various cables connect to provide the appropriate voltages at the proper pins.
7. If the IM15 requires repair, contact a professional technician instead of attempting repairs yourself.

6. COMPLIANCE STATEMENTS

FCC COMPLIANCE STATEMENT

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference.
2. This device must accept any interference received, including interference that may cause undesired operation.

Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

Frequency from 5150 to 5250MHz is for indoor use.

Warning

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

Caution

Any changes or modifications not expressly approved by the manufacturer could void the user's authority to operate this equipment.

Radiation Exposure

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20cm between the radiator and your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

INDUSTRY CANADA STATEMENT

This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada's licence-exempt RSS(s). Operation is subject to the following two conditions:

1. This device may not cause interference, and
2. This device must accept any interference, including interference that may cause undesired operation of the device.

French translation: Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes: 1) l'appareil ne doit pas produire de brouillage, et 2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement.

The user manual for LE-LAN devices shall contain instructions related to the restrictions mentioned in the above sections, namely that:

• The device for operation in the band 5150–5250 MHz is only for indoor use to reduce the potential for harmful interference to co-channel mobile satellite systems.
• French translation: le dispositif utilisé dans la bande 5150-5250 MHz est réservé à une utilisation en intérieur afin de réduire le risque de brouillage préjudiciable aux systèmes mobiles par satellite dans le même canal.

Note: The above description only applies to IM15 BW, IM15 4GBW.

Additional Compliance Information

This device and its antenna(s) must not be co-located or operating in conjunction with any other antenna or transmitter, except tested built-in radios.

French translation: Cet appareil et son antenne ne doivent pas être situés ou fonctionner en conjonction avec une autre antenne ou un autre émetteur, exception faites des radios intégrées qui ont été testées.

The Country Code Selection feature is disabled for products marketed in the US/Canada.

French translation: La fonction de sélection de l'indicatif du pays est désactivée pour les produits commercialisés aux États-Unis et au Canada.

Radiation Exposure Statement (IC)

This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20cm between the radiator and your body.

French translation: Cet équipement est conforme aux limites d'exposition aux rayonnements IC établies pour un environnement non contrôlé. Cet équipement doit être installé et utilisé avec un minimum de 20 cm de distance entre la source de rayonnement et votre corps.

7. INDEX OF ICONS

• ♻️ [do not throw away]: Requires professional recycling.
• [Class II equipment]: Class II equipment.
• ? [indoor use only]: For indoor use only.
• ⚡ [energy efficiency level VI]: Energy efficiency marking (level VI).
• 〰️ [AC voltage]: AC voltage.
• ⎓ [DC voltage]: DC voltage.

Although PAX Computer Technology (Shenzhen) Co., Ltd. strives to maintain the accuracy of the information presented in this document, it reserves the right to change product specifications without prior notification and does not guarantee that the material presented herein will accurately reflect the set up, installation, or use of PAX products.

Contact Information

Manufacturer

PAX Computer Technology (Shenzhen) Co. Ltd.

Address: 4FL, Building #3, Software Park, 2nd Central Science-Tech RD, High-Tech Industrial Park, Shenzhen, Guangdong, PRC.

Tel: +86 755-86169630

Website: www.pax.com.cn

Responsible Party

PAX Technology Inc.

Address: 8880 Freedom Crossing Trail, Building 400, 3rd Floor, Suite 300, Jacksonville, Florida 32256

Tel: 1-877-859-0099

Website: www.pax.us