PAX D195 Mobile Payment Terminal Quick Setup Guide

1. Contents Checklist

Please check the components after unpacking. If any one of them is missing, or if there is a page missing from the product manual, please contact the dealer.

2. Installation

SAM/SIM Card:

1. Remove the battery cover.
2. Remove the battery.
3. Insert the SAM/SIM card to the corresponding card slot (Note: The default hardware configuration only supports SIM 1 slot).

Battery:

Align the battery tip side to the battery tip in the terminal and insert.

3. Instruction

Power ON/OFF:

• Power on: Plug in the power adapter or insert the battery. Press the power button for 3 seconds until the PAX LOGO displays on the LCD.
• Power off: Press the power button for 3 seconds until "Power off" displays on the LCD, then press "ENTER". The POS terminal will then be turned off.

IC Card:

Put the IC card chip side upward, push the IC card into the slot until it reaches the bottom.

Contactless Card:

The card read area is above the LCD. Place the card above the LCD.

Battery Charge Display:

Connecting the USB port with an external adapter can charge the battery. A charging indicator will be displayed.

Battery Charge Style:

Please use the original adapter for charging.

Working Environment:

• Temperature: 0°C~45°C (32°F~113°F)
• Humidity: 10%~93% (non-condensing)

Storage Environment:

• Temperature: -20°C~70°C (-4°F~158°F)
• Humidity: 5%~95% (non-condensing)

4. Installation and Usage Tips

1. Avoid placing the terminal in direct sunlight, high temperature, moist, or dusty environments.
2. Do not allow non-professionals to repair the terminal.
3. Before inserting a card, please check the inside and around of the IC card slot. If you find any suspicious objects, report them to the relevant administrator.

5. Lithium Ion Battery Usage Tips

WARNING:

1. Do not use the battery in sunlight or smoky, dusty environments.
2. Do not strike, squeeze, tread on the battery, or throw it into liquid or fire.
3. If the battery is visibly damaged, deformed, or exhibits serious exothermic behavior, stop using it immediately and replace it!
4. If the continuous working time is only half of that of a new battery, the battery life may be at its end. Please replace it!
5. Always use the specified battery model and charger; otherwise, explosion may occur.
6. Charging time should not exceed 24 hours. If the battery is out of power, please recharge it promptly. Avoid damaging the battery through over-charging or over-discharging.
7. If the device is not used for a long time, please recharge the battery every 6 months to prevent shortening its lifespan.
8. It is suggested to replace the battery when it has been used for 2 years.
9. Be sure to follow the instructions to dispose of used batteries properly. ♻️ [Recycle Symbol]

6. Icon Meanings

• Do not throw away, need professional recycling. ♻️ [Recycle Symbol]
• Class II Equipment ⚡ [Class II Equipment]
• For indoor use only ? [Indoor Use Only]
• Energy Efficiency Marking ? [Energy Efficiency]
• AC voltage ? [AC Voltage]
• DC voltage ? [DC Voltage]

Regulatory Information and Manufacturer Details

The full text of the EU declaration of conformity is available at: https://www.pax.com.cn/product/ce/list/

P/N: 200312000000866

PAX continually invests to maintain its high-quality products up-to-date with the latest certifications. A comprehensive list can be requested via the website's contact form or on downloadable product brochures.

Manufacturer:

Built by: PAX Computer Technology (Shenzhen) Co. Ltd.

Address: 4/F, No.3 Building, Software Park, Second Central Science-Tech Road, High-Tech Industrial Park, Shenzhen, Guangdong, China.

Tel: +86 755 86169630

Website: www.pax.com.cn

FCC and IC Compliance

FCC Regulations:

This device has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

Caution: Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

RF Exposure Information (SAR) - FCC:

The SAR limit of FCC is 1.6W/kg averaged over one gram of tissue. For body-worn operation, this device has been tested and meets the FCC exposure guidelines. When used with an accessory, the accessory should not contain any metal elements and should be positioned a minimum of 5 mm from the body. RF exposure compliance with any accessory that contains metal was not tested and certified, and use of such accessory should be avoided.

IC Statement (Industry Canada):

This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: 1) this device may not cause interference, and 2) this device must accept any interference, including interference that may cause undesired operation of the device.

Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes: 1) l'appareil ne doit pas produire de brouillage, et 2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement.

The device is intended to be operated in the 5150~5250 frequency range. It is restricted to indoor environments only in Canada.

Le dispositif fonctionne dans une gamme de fréquences 5150~5250. L'environnement intérieur est restreint seulement au Canada.

RF Exposure Information (SAR) - IC:

This equipment complies with RSS 102 radiation exposure limits set forth for an uncontrolled environment. The end-user must follow the specific operating instructions for satisfying RF exposure compliance. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

The portable device is designed to meet the requirements for exposure to radio waves established by the ISED. These requirements set a SAR limit of 1.6 W/kg averaged over one gram of tissue. The highest SAR value reported under this standard during product certification for use when properly worn on the body.

Ce matériel est conforme aux limites d'exposition aux radiations RSS 102 fixées pour un environnement non contrôlé. L'utilisateur final doit suivre les instructions opérationnelles spécifiques pour satisfaire à la conformité à l'exposition RF. Cet émetteur ne doit pas être co-localisé ni fonctionné conjointement avec aucune autre antenne ou émetteur.

L'appareil portable est conçu pour répondre aux exigences relatives à l'exposition aux ondes radio électriques établies par l'ISED. Ces exigences fixent une limite de SAR de 1,6 W/kg moyenne de plus d'un gram de tissu. La valeur SAR la plus élevée signalée en vertu de cette norme pendant la certification du produit à utiliser lorsqu'elle est correctement portée sur le corps.

FCC Supplier's Declaration of Conformity:

Product: Smart Mobile Payment Terminal / D195

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

FCC ID and IC ID can be found by opening the battery cover.

Responsible Party: PAX Technology, Inc.

Address: 8880 Freedom Crossing Trail, Building 400, 3rd Floor Suite 300, Jacksonville, Florida, 32256

Help-desk: 1877-859-0099

Brand: PAX Empowering Digital Payments