VICTA
Parts Manual
Manufacturer Number: 2691588-B
Model: Victa, Commercial 560 Alloy SP, 850
Table of Contents
Deck Group
Note: Unless noted otherwise, use the standard torque specifications.
Diagram Description: This section presents an exploded view of the deck assembly. It details the arrangement of various components, with numbered references pointing to the parts list for identification. Key parts include the chassis, gearbox curtain, mulch plug, bumper, wear plate pack, segment, discharge flap assembly, chute pack, skid plate pack, rear flap pack, and belt cover pack.
Parts List:
| REF NO | PART NO | QTY | DESCRIPTION |
|---|---|---|---|
| 20 | CH86859AW | 1 | CHASSIS, 560, Aztec Silver |
| 25 | ---- | 1 | GEARBOX CURTAIN -(Not a serviceable part) |
| 30 | CH85985A | 1 | PLUG, 4 Stroke Models Only |
| 40 | CH86939AW | 1 | BUMPER -(Includes screws) |
| 50 | CH86897AW | 1 | WEAR PLATE PACK -(Includes screws & washers) |
| 60 | CH86861AW | 1 | SEGMENT |
| 70 | ---- | 1 | MULCHING PLUG -(Not a serviceable part) |
| 80 | CH86885AW | 1 | KNOB, Mulch Plug |
| 90 | CH86893AW | 1 | MULCH PLUG PACK -(Includes Ref. Nos. 70 & 80) |
| 100 | CH87226A | 1 | DISCHARGE FLAP ASSEMBLY |
| 110 | CH86895AW | 1 | CHUTE PACK -(Includes screws & washers) |
| 120 | CH86899AW | 1 | SKID PLATE PACK -(Includes screws & washers) |
| 140 | CH88436A | 1 | REAR FLAP PACK, 560 |
| 160 | CH86898AW | 1 | BELT COVER PACK -(Includes screws & washers) |
Engine & Blade Group
Note: Unless noted otherwise, use the standard torque specifications.
Diagram Description: This section displays an exploded view of the engine and blade assembly. It shows the arrangement of the engine, blade disc, blades, and associated hardware. Key components include the Briggs & Stratton 850 Series engine, blade disc, lo-lift and hi-lift blades, and various bolts, washers, and nuts.
Parts List:
| REF NO | PART NO | QTY | DESCRIPTION |
|---|---|---|---|
| 10 | 123P32-0031-H5 | 1 | ** ENGINE, Briggs & Stratton 850 Series |
| 80 | HA21320D | 3 | BOLT, Taptite, HW, 3/8 UNC x 30 |
| 90 | HA22277D | 3 | WASHER, Engine Mounting |
| 271 | EE14476A | 1 | PULLEY & SLEEVE, Engine, 4-Stroke, 7/8" |
| 290 | CA09442G | 1 | BLADE DISC, Oval |
| 300 | ---- | 2 | BLADE, Mower, Lo-Lift |
| 305 | CA09507B | 2 | BLADE, Hi Lift |
| 310 | ---- | 2 | BOLT, Blade |
| 320 | CA09347A | 2 | WASHER, Blade Tension |
| 330 | HA25276BZ | 2 | WASHER, Belleville |
| 340 | CA09241D | 2 | NUT, Nylock, 3/8 UNC |
| 350 | EE14484B | 1 | BOLT, Flanged, Blade Disc |
| 360 | EN73054B | 1 | WASHER, Blade Disc |
| 370 | CA09276B | 1 | KIT, Blade & Bolt, Hi-Profile (1 Pair) -(Includes Ref. No. 305, 310, 320, 330 & 340) |
| 380 | CA09584B | 1 | KIT, Blade & Bolt, Lo-Lift (1 Pair) -(Includes Ref. No. 300, 310, 320, 330 & 340) |
| 390 | CA09277S | 1 | KIT, Hardware, Bolt, Washer, Nut (1 Pack) -(Includes Ref. No. 310, 330 & 340) |
| 400 | CA09277P | 1 | KIT, Hardware, Blade, Washer, Nut , Bulk Pack (50 Pairs) -(Includes Ref. No. 310, 330 & 340) |
Footnotes: Note** Engine Style may vary from illustration. To verify your specific engine model, please reference the ID Tag located on your engine. See your local Briggs & Stratton distributor for parts and service.
Handles & Controls Group
Note: Unless noted otherwise, use the standard torque specifications.
Diagram Description: This section shows an exploded view of the handles and controls assembly. It illustrates the components that make up the handle structure, including the upper and lower handles, bail arm, and throttle control. Key parts include handles, saddle plates, nuts, levers, cables, and throttle components.
Parts List:
| REF NO | PART NO | QTY | DESCRIPTION |
|---|---|---|---|
| 20 | HA20492D | 4 | BOLT, Hex Head, M8 x 65 |
| 30 | CH87047GW | 2 | HANDLE, Lower, 560 |
| 40 | CH80854GZ | 2 | PLATE, Saddle, Heavy |
| 50 | VV17130D | 2 | PLATE, Saddle |
| 60 | ---- | 4 | NUT, Nylock, M8 |
| 70 | CH88061P | 1 | WINGED LOCKING LEVER PACK V2 -(2 Sets Included, Kit includes Lever, Washer & Nut) |
| 100 | CH87048G | 1 | HANDLE, Upper, 560 S/P |
| 120 | CH88439A | 1 | BAIL ARM ASSEMBLY |
| 130 | HA24982D | 1 | NUT, Nylock, M6 |
| 140 | CH86788A | 2 | SLEEVE, Bearing |
| 150 | 80079136 | 1 | UPPER HANDLE ASSEMBLY -(Includes Ref. Nos. 100, 120, 130, 140 &160) |
| 160 | CH87424A | 1 | CABLE, Drive Clutch |
| 170 | ---- | 1 | CLAMP, 22mm |
| 180 | ---- | 1 | SCREW, M5 x 18 -(Not a serviceable part) |
| 200 | TC05064B | 1 | THROTTLE, Pro Control -(Includes Ref. Nos. 170 & 180) |
| 220 | CH86896AW | 1 | TENSIONER MOUNT PACK 560 |
Wheels Group
Note: Unless noted otherwise, use the standard torque specifications.
Diagram Description: This section provides an exploded view of the wheels assembly. It illustrates the components of the front and rear wheel systems, including axles, bushings, wheels, and related hardware. Key parts include front and rear axles, various wheels, hubcaps, and drive gears.
Parts List:
| REF NO | PART NO | QTY | DESCRIPTION |
|---|---|---|---|
| 10 | ---- | 4 | SCREW, Hex Flange, M5 x 16 -(Not a serviceable part.) |
| 20 | ---- | 6 | SCREW, Pan Torx Trilobe, M6 x 19 -(Not a serviceable part.) |
| 30 | ---- | 1 | * SCREW, Pan Torx, Self Tap, ST4.2 x 16 -(Not a serviceable part.) |
| 40 | CH84142A | 2 | RING, Sealing |
| 50 | CH84185U | 2 | BUSHING, Rear Axle |
| 70 | ---- | 1 | * SCREW, Pan Torx, Self Tap, ST4.2 x 10 -(Not a serviceable part.) |
| 80 | ---- | 2 | SLEEVE, Fixed |
| 85-1 | ---- | 1 | SPRING, RH, Black -(Not a serviceable part.) |
| 85-2 | ---- | 1 | SPRING, LH, Yellow -(Not a serviceable part.) |
| 90 | ---- | 1 | DRIVE GEAR -(Not a serviceable part.) |
| 95 | ---- | 1 | SLEEVE, Drive -(Not a serviceable part.) |
| 100 | ---- | 2 | PIN, Roll 1/8 x 3/4 SP -(Not a serviceable part.) |
| 110 | CH86881AW | 1 | AXLE, Front |
| 120 | CH86276A | 2 | BUSHING, Front Axle |
| 130 | CH81445A | 4 | DUST SEAL |
| 140 | 80084367 | 2 | BEARING -(Replaces Part Nos. HA25463A) |
| 150 | CH88275D | 4 | RETAINING PLATE, Axle |
| 160 | CH87420A | 1 | BRACKET, Gearbox 560 |
| 180 | 80080431 | 1 | KIT, Variable Speed |
| 185 | CH87296A | 1 | GEARBOX GT-MC600 |
| 190 | CH86938AW | 1 | AXLE, Rear |
| 190-1 | ---- | 1 | GEAR, Over - Run Clutch, RH Black -(Not a serviceable part.) |
| 190-2 | ---- | 1 | GEAR, Over - Run Clutch, RH Yellow -(Not a serviceable part.) |
| 200-1 | CH86816S | 1 | OVER RUN CLUTCH KIT |
| 200-2 | CH86823S | 1 | OVER RUN SPRING KIT |
| 210 | CH85943A | 1 | SPRING |
| 220 | HA25131D | 2 | E-CLIP |
| 240 | CH82847A | 2 | SEAL, Drive Wheel |
| 250 | CH86334A | 4 | WHEEL, Pro, 8" |
| 260 | CH86333A | 2 | WHEEL, Pro, 8", REAR |
| 250-1 | ---- | 2 | WASHER, Wheel, Front -(Not a serviceable part.) |
| 250-2 | ---- | 2 | BUSHING, Wheel, Front -(Not a serviceable part.) |
| 250-3 | ---- | 2 | WASHER, Wheel, Front |
| 251 | CH86298A | 4 | CAPTIVATED CLIP, Wheel |
| 350 | CH86112A | 4 | HUBCAP, Black |
| 370 | CH86862AW | 1 | CONLINK |
| 400 | 80085135 | 1 | V-BELT, 6736 Power Rated -(Replaces Part Nos. CH85666A) |
Torque Specification Chart & Hardware Identification
Torque Specification Chart (Metric)
| Property Class | 5.6 | 8.8 | 10.9 | 12.9 | ||||
|---|---|---|---|---|---|---|---|---|
| in/lbs | Nm | in/lbs | Nm | in/lbs | Nm | in/lbs | Nm | |
| M3 | 5.88 | .56 | 13.44 | 1.28 | 19.2 | 1.80 | 22.92 | 2.15 |
| M4 | 13.44 | 1.28 | 30.72 | 2.90 | 43.44 | 4.10 | 52.56 | 4.95 |
| M5 | 26.4 | 2.50 | 60.96 | 5.75 | 5.97 | 8.10 | 7.15 | 9.7 |
| M6 | 44.64 | 4.3 | 7.3 | 9.9 | 10.3 | 14 | 12.1 | 16.5 |
| M7 | 5.2 | 7.1 | 12.1 | 16.5 | 16.9 | 23 | 19.9 | 27 |
| M8 | 7.7 | 10.5 | 17.7 | 24 | 25 | 34 | 29 | 40 |
| M10 | 15 | 21 | 35 | 48 | 50 | 67 | 59 | 81 |
| M12 | 26 | 36 | 61 | 83 | 86.2 | 117 | 103 | 140 |
| M14 | 42 | 58 | 101 | 132 | 136 | 185 | 162 | 220 |
| M16 | 64 | 88 | 147 | 200 | 210 | 285 | 250 | 340 |
| M18 | 89 | 121 | 202 | 275 | 287 | 390 | 346 | 470 |
| M20 | 126 | 171 | 290 | 390 | 405 | 550 | 486 | 660 |
| M22 | 169 | 230 | 390 | 530 | 559 | 745 | 656 | 890 |
| M24 | 217 | 295 | 497 | 375 | 708 | 960 | 840 | 1140 |
| M27 | 320 | 435 | 733 | 995 | 1032 | 1400 | 1239 | 1680 |
| M30 | 435 | 590 | 995 | 1350 | 1401 | 1900 | 1681 | 2280 |
| M33 | 590 | 800 | 1349 | 1830 | 1902 | 2580 | 2278 | 3090 |
| M36 | 759 | 1030 | 1740 | 2360 | 2441 | 3310 | 2935 | 3980 |
| M39 | 988 | 1340 | 2249 | 3050 | 3163 | 4290 | 3798 | 5150 |
Torque Specification Chart (Standard)
| Hardware Grade | SAE Grade 2 | SAE Grade 5 | SAE Grade 8 | |||
|---|---|---|---|---|---|---|
| ft/lbs | Nm | ft/lbs | Nm | ft/lbs | Nm | |
| 8-32 | 19 | 2.1 | 30 | 3.4 | 41 | 4.6 |
| 8-36 | 20 | 2.3 | 31 | 3.5 | 43 | 4.9 |
| 10-24 | 27 | 3.1 | 43 | 4.9 | 60 | 6.8 |
| 10-32 | 31 | 3.5 | 49 | 5.5 | 68 | 7.7 |
| 1/4-20 | 66 | 7.6 | 8 | 10.9 | 12 | 16.3 |
| 1/4-28 | 76 | 8.6 | 10 | 13.6 | 14 | 19.0 |
| 5/16-18 | 11 | 15.0 | 17 | 23.1 | 25 | 34.0 |
| 5/16-24 | 12 | 16.3 | 19 | 25.8 | 29 | 34.0 |
| 3/8-16 | 20 | 27.2 | 30 | 40.8 | 45 | 61.2 |
| 3/8-24 | 23 | 31.3 | 35 | 47.6 | 50 | 68.0 |
| 7/16-14 | 30 | 40.8 | 50 | 68.0 | 70 | 95.2 |
| 7/16-20 | 35 | 47.6 | 55 | 74.8 | 80 | 108.8 |
| 1/2-13 | 50 | 68.0 | 75 | 102.0 | 110 | 149.6 |
| 1/2-20 | 55 | 74.8 | 90 | 122.4 | 120 | 163.2 |
| 9/16-12 | 65 | 88.4 | 110 | 149.6 | 150 | 204.0 |
| 9/16-18 | 75 | 102.0 | 120 | 163.2 | 170 | 231.2 |
| 5/8-11 | 90 | 122.4 | 150 | 204.0 | 220 | 299.2 |
| 5/8-18 | 100 | 136 | 180 | 244.8 | 240 | 326.4 |
| 3/4-10 | 160 | 217.6 | 260 | 353.6 | 386 | 525.0 |
| 3/4-16 | 180 | 244.8 | 300 | 408.0 | 420 | 571.2 |
| 7/8-9 | 140 | 190.4 | 400 | 544.0 | 600 | 816.0 |
| 7/8-14 | 155 | 210.8 | 440 | 598.4 | 660 | 897.6 |
| 1-8 | 220 | 299.2 | 580 | 788.8 | 900 | 1,244.0 |
| 1-12 | 240 | 326.4 | 640 | 870.4 | 1,000 | 1,360.0 |
Hardware Identification:
- Common Hardware Types: Hex Head Capscrew, Washer, Carriage Bolt, Lockwasher, Hex Nut.
- Standard Hardware Sizing: Explains nominal size, thread diameter, and length for bolts/nuts.
- Wrench & Fastener Size Guide: Lists common fastener sizes and corresponding wrench sizes.
Notes on Torque Values:
- Torque values apply to most hardware, excluding specific types like locknuts, self-tapping screws, thread forming screws, sheet metal screws and socket head setscrews.
- Recommended seating torque for locknuts: a. for prevailing torque locknuts - use 65% of grade 5 torques. b. for flange whizlock nuts and screws - use 135% of grade 5 torques.
- Unless otherwise noted on assembly drawings, all torque values must meet this specification.
