GAMEMAX Cyclops PC Case

Specifications

Explosive View

The chassis components are identified as follows:

• 1: Chassis
• 2: Left tempered glass side panel
• 3: Right side panel
• 4: Front panel
• 5: PSU cover
• 6: Dust-proof filter on the bottom
• 7: Dust-proof filter on the top
• 8: HDD Bracket
• 9: M/B installation position
• 10: 1*120mm fan on the front
• 11: 1*120mm fan on the rear

I/O Ports

The top panel features the following I/O ports:

• 1: Power Switch
• 2: Reset
• 3: Light brightness control
• 4: Light mode control
• 5: HD Audio
• 6: USB 2.0
• 7: USB 3.1 GEN1

Side Panel Installation

To install or remove the side panels:

1. Locate and loosen the drop-proof screws on the right side panel.
2. Pull the right side panel outwards in the direction indicated by the arrowhead to remove it. This allows for easy access to the interior.

The front panel can be removed by stabilizing the chassis with one hand and applying gradual pulling force from the bottom with the other hand.

Power Supply Installation

To install the Power Supply Unit (PSU):

1. Ensure the right side panel is removed for access.
2. Insert the ATX PSU into the designated bay at the bottom of the chassis, following the direction indicated by the arrowhead.

VGA Card Installation

To install a graphics card (VGA card):

1. Remove the protective covers from the PCI expansion slots at the rear of the chassis.
2. Insert the graphics card into the appropriate PCI-e slot on the motherboard.
3. Secure the graphics card in place using a screw.

Motherboard Installation

To install the motherboard:

1. Ensure the pre-installed motherboard screws are in place in the chassis.
2. Carefully position the motherboard into the chassis, aligning it with the standoffs and screw holes.
3. Secure the motherboard by tightening screws into the standoffs.

HDD and SSD Installation

The chassis supports up to two 3.5" HDDs and two 2.5" SSDs.

3.5" HDD Installation:

• Install 3.5" drives using the toolless mounting system. No screws are required for 3.5" drives.

2.5" SSD Installation:

• For 2.5" drives, use the fine-thread Phillips head screws (the same screws used for the motherboard) to secure the drive.
• Optional mounting positions are available for 2.5" drives.

Fan and Water Cooling Installation

The chassis supports various cooling configurations:

Fan Installation:

• Fans can be installed in the front, top, and rear mounting points as specified.
• The front and rear panels include 120mm ARGB fans.

Water Cooling Installation:

• A 120mm or 240mm radiator can be installed in the front panel.
• A 120mm radiator can be installed in the rear panel.

Installation involves placing the radiator or fan in the desired location and securing it with screws.

V1.7 A-RGB (RAINBOW) Control Hub

This section details the features and connections for the A-RGB control hub.

1. Product Features:

• 1-1: Supports 18 color modes.
• 1-2: Allows adjustment of modes and colors.
• 1-3: Supports brightness adjustment.
• 1-4: Powered by SATA connection from the PSU.
• 1-5: Compatible with programmable RGB interfaces of RAINBOW motherboards.
• 1-6: Can connect LED strips compatible with ASUS Aura Sync.

2. Functional Description:

• 2-1. Change MB and Controller Mode: Press and hold the MODE key for 3 seconds. A white light flicker indicates switching to Motherboard (MB) mode. Release the key to enter MB mode. Pressing MODE again switches back to controller mode.
• 2-2. Switch Mode (Controller Mode): In controller mode, press and hold MODE for 3 seconds; the white light flickers. Continuing to press turns off the light. Pressing MODE again turns the light back on.
• 2-3. Memory Function: The controller retains the last lighting setting.
• 2-4. Mode and Color Button: Short press to change the lighting mode. Short press twice to change the color within the current mode.
• 2-5. Brightness Button: Short press to adjust LED brightness. (Functionality may vary by version).
• 2-6. AURA SYNC: When connected to the motherboard's ARGB interface, lighting control can be managed via key presses.
• 2-7. Strip: Can connect LED strips with ASUS standard 3-pin connectors.

3. Interface Definitions:

• 3-1. ARGB: Connects ARGB fans or light bars. Align the triangle mark on the plug with the arrow on the controller.
• 3-2. MB ARGB: Connects to the motherboard's ARGB interface. Align the triangle mark on the plug with the arrow on the controller.
• 3-3. SATA: Power supply interface, outputs 5V DC voltage.
• 3-4. SW: Switch interface. Some products have mode and color control functions; others have brightness adjustment.
• 3-5. STRIP: Can connect LED strips with ASUS standard 3-pin connectors.

The SATA Hub is powered by a standard SATA connection from the power supply.