Components
- 1: Headboard Panel (x2)
- 2: Side Rail Connector (x4)
- 3: Footboard Panel (x2)
- 4: Footboard Connector (x2)
- 5: Leg (x8)
- 6: Center Support Rail (x4)
- 7: Center Support Leg (x2)
- 8: Slat (x15)
- 9: Support Bracket (x2)
- 10: Headboard Side Rail (x2)
- 11: Footboard Side Rail (x2)
- 12: Headboard Support Bar (x1)
- 13: Footboard Support Bar (x1)
- 14: Connector (x?)
- 15: Connector (x?)
- 16: Connector (x?)
- 17: Top Rail (x2)
- 18: Vertical Post (x4)
- 19: Bottom Rail (x2)
- 20: Connector (x?)
Hardware
- A: M2x100mm Screw (x14)
- B: Cam Lock (x16)
- C: M6x100mm Screw (x4)
- D: Ø8x30mm Screw (x42)
- E: M6x70mm Screw (x2)
- F: Threaded Stud (x2)
- G: Nut (x4)
- H: Curved Washer (x4)
- J: Wood Glue (x2)
- K: Spanner (x2)
- L: Allen Key (x1)
- M: Ø4x30mm Screw (x34)
- N: Ø4x30mm Screw (x60)
- O: Ø7x70mm Hex Bolt (x4)
- P: Cam Screw (x8)
- Q: Cam Connector/Lock (x8)
Assembly Instructions
Step 1: Connect Panels and Support Bars
Connect the headboard panels (1) and footboard panels (3) to the side rails (10, 11) using screws (D). Attach the headboard support bar (12) and footboard support bar (13) to their respective panels.
Step 2: Assemble Legs
Assemble the legs (5) onto the headboard and footboard components. Apply wood glue (J) to the connectors (2, 3, 4) before attaching the legs.
Step 3: Insert Cam Screws
Insert cam screws (P) into the pre-drilled holes on the footboard side rails (11). Repeat this process for both footboard side rails.
⚠️ [Warning Symbol] Indicates correct insertion.
✔️ [Checkmark Symbol] Correct.
❌ [Cross Symbol] Incorrect.
Step 4: Connect Side Rails
Attach the headboard side rails (10) to the footboard side rails (11) using cam connectors (Q). Ensure the cam connectors are properly engaged to secure the connection. Repeat for both sides.
Visuals show the cam lock mechanism engaging.
Step 5: Assemble Headboard and Footboard
Connect the headboard panels (1) and footboard panels (3) to the side rail assembly. Use screws (A, C) and cam locks (B) to secure these connections.
Notes:
- ✔️ Ensure the arrows on parts 3 and 4 are oriented upwards.
- ✔️ Ensure the hole on cam lock (B) is facing the 3/4 position.
Step 6: Assemble Center Support Frame
Construct the center support frame. Attach the center support rails (6) to the center support legs (7) using threaded studs (F), nuts (G), and curved washers (H). Use the spanner (K) to tighten the nuts. Repeat this step for both center support assemblies.
Visuals show the assembly sequence and tool usage.
Step 7: Attach Center Support and Slats
Attach the center support rails (6) to the bed frame. Then, attach the slats (8) to the center support rails (6) using screws (M). There are approximately 15 slats.
Close-up views show screw insertion into slats.
Step 8: Attach Top Rails
Attach the top rails (17) to the vertical posts (18) using hex bolts (O).
Close-up view shows bolt insertion.
Step 9: Assemble Main Bed Frame
Assemble the main bed frame by connecting the headboard and footboard assemblies to the side rails. Use screws (A) and cam locks (B) for these connections. Attach the center support rails (6) and the footboard support bar (13).
Step 10: Install Slats
Place the slats (8) across the bed frame and secure them using screws (N).
Step 11: Attach Support Brackets
Attach the support brackets (9) to the underside of the bed frame using screws (M).
Note: For your safety, it is recommended that two people perform this step.
Notes
This section is blank in the original document.
Kogan Help Centre
