Components
Lay all components out on a clean floor and ensure all parts are included. If any pieces are missing, check all packaging thoroughly, then contact help.Kogan.com for assistance.
- 1: Top Panel
- 2: Bottom Panel
- 3: Back Panel
- 4: Left Side Panel
- 5: Middle Divider Panel
- 6: Right Side Panel
- 7: Shelf
- 8: Left Door
- 9: Right Door
- 10: Middle Door (with slats)
- 11: Adjustable Feet (x4)
- 12: Shelf Supports (x2)
- 13: Cam Lock Dowels (x4)
Hardware
| Identifier | Description | Quantity |
|---|---|---|
| A | Cam Bolt | x12 |
| B | Cam Lock | x12 |
| C | Wooden Dowel (6x30mm) | x20 |
| D | Screw (3x14mm) | x14 |
| E | Magnetic Catch | x2 |
| F | Screw | x2 |
| G | Screw (4x40mm) | x10 |
| H | Screw (4x14mm) | x26 |
| I | Screw (3.5x12mm) | x48 |
| J | Hinge | x8 |
| K | Door Handle | x4 |
| L | Screw (M4x22mm) | x4 |
| M | Bracket | x10 |
| N | Bracket | x2 |
| O | Wall Plug | x2 |
| P | Screw (2.5x12mm) | x2 |
| Q | Washer | x2 |
Assembly Instructions
Step 1
Attach four Cam Bolts (A) to the designated holes on panels 5 and 6. Insert two Magnetic Catches (E) into the corresponding holes on panel 5 and secure them with four Screws (D).
Step 2
Insert two Wooden Dowels (C) into the pre-drilled holes on the edge of panel 6. Insert two Wooden Dowels (C) into the corresponding holes on panel 2. Connect panel 6 to panel 2 using two Cam Locks (B).
Step 3
Insert two Wooden Dowels (C) into the pre-drilled holes on the edge of panel 5. Insert two Wooden Dowels (C) into the corresponding holes on panel 2. Connect panel 5 to panel 2 using two Cam Locks (B).
Step 4
Screw eight Cam Bolts (A) into the designated holes on the underside of the Top Panel (1). Attach two Brackets (N) to the underside of Panel 1 using two Screws (H).
Step 5
Insert eight Wooden Dowels (C) into the top edges of panels 4, 5, 6, and 7. Attach panels 4, 5, 6, and 7 to the Bottom Panel (2) using eight Cam Locks (B).
Step 6
Insert eight Wooden Dowels (C) into the top edges of panels 4, 5, 6, and 7. Attach the Back Panel (3) to the assembled structure by screwing eight Screws (G) through the back panel into the top edges of the side and divider panels.
Step 7
Attach the eleven Adjustable Feet (11) to the underside of the Top Panel (3) using twenty-four Screws (H). Note: Component 11 has an adjustable foot. Rotate to adjust if required for leveling.
Step 8: Prepare Doors
Repeat this step for the remaining doors. Attach two Hinges (J) to each door (8, 9) using four Screws (I) and two Screws (L) per hinge. Attach one Magnetic Catch (E) to each door using two Screws (F). Attach one Door Handle (K) to each door using two Screws (P).
Step 9: Attach Doors
Attach the prepared doors (8, 9) to the main unit. Screw the hinges (J) into the pre-drilled holes on the unit using thirty-two Screws (I).
Step 10: Attach Back Brackets
Attach ten Brackets (M) to the back of the unit using ten Screws (D).
Step 11: Wall Mounting
Secure the unit to the wall for stability. Insert two Wall Plugs (O) into the wall at the desired height. Attach the unit to the wall by screwing two Screws (G) through the Brackets (N) on the back of the unit into the Wall Plugs (O).
TOPPLING FURNITURE WARNING:
- It is strongly recommended that this product is permanently fixed to the wall.
- Please seek professional advice if you are in doubt of what fixing device to use.
- Regularly check that anchors are securely maintained.
- Stability of tall items may be affected by thick carpets or uneven floors.
- Do not place unanchored televisions on furniture.
Caution! For your safety when attaching the anchor fixings, please note the following: Check any electrical wires or plumbing inside the wall before drilling any holes (if you are unsure, please seek professional advice from a qualified tradesperson).
Step 12: Completion
The Edward Entertainment Unit assembly is now completed!
Kogan Help Centre
