ℹ️ Document Conversion Notice: This document has been converted from PDF and formatted to fit this screen. Diagrams and images may be available only in the original here.

SFP-10G-PCxxx Transceiver Test Report (Cisco)

Brand: FS

Certifications: LIFETIME WARRANTY, ISO 27001, ISO 14001, ISO 45001, ISO 9001, REACH Compliant, CE

1. Test Purpose

By building test scenarios and simulating the customer's usage environment, we test whether the module performance meets the customer's requirements.

2. Test Result Summary

Table 2-1: Test Result Summary

Test Items	Test Result
Muti-Version	Pass
Connectivity	Pass
Module Basic Information	Pass

3. Test Equipment Used

Table 3-1: Test Equipment Used

Vendor	Device	Soft Version/Compatible Brand	Serial Number
Cisco Switch	C9300X-12Y	17.12.03	/
Intel Network Interface Card (NIC)	Intel XXV710-DA2	9.50 0x8000f177	/
FS Optical Transceiver Module	SFP-10G-PCxxx	Cisco Compatible	A2403122821-2 A2403122821-1
FS Server	RS7260	/	/

4. Test Data

4.1 Test Scenario

Network topology

A network topology diagram shows a Cisco C9300X-12Y switch connected to an Intel XXV710-DA2 NIC via an FS SFP-10G-PCxxx module and an FS RS7260 server. The connection is represented by lines indicating data flow.

Interoperability test scenario

An image shows a rack of network equipment, including switches and servers, illustrating the physical setup for interoperability testing.

Test Premise

Confirm the brand, quantity, and placement of the switches to be tested.
Prepare control cables, test software, and optical fiber patch cords. Power on the switches in advance.
Locate the Console port on the switch (often marked "CON", "IOIOI", or with a computer monitor icon). Connect the switch to the computer using a control cable.
Before connecting the software, confirm the computer's COM port in the device manager.

Test Method

Steps for using SecureCRT Portable:

Open SecureCRT Portable and enter the quick connection interface.
Protocol selection: Serial
Port selection: Match the COM port identified in the previous step.
Baud rate selection: Match the baud rate of the target switch's port.
Flow control: Do not check this option.
Other configurations can remain at default values.

A screenshot shows the SecureCRT Portable quick connect dialog with 'Serial' selected for Protocol, a COM port (e.g., COM28) selected, Baud rate set to 38400, and Flow Control unchecked.

4.2 Test Result

Switch port status

Table 4-2: Test Result

Port	Name	Status	Vlan	Duplex	Speed	Type
Twe1/0/1	connected	1	full	10G	SFP-10GBase-CX1
Twe1/0/2	connected	1	full	10G	SFP-10GBase-CX1
Twe1/0/3	notconnect	1	auto	auto	unknown
Twe1/0/4	notconnect	1	auto	auto	unknown
Twe1/0/5	notconnect	1	auto	auto	unknown
Twe1/0/6	notconnect	1	auto	auto	unknown
Twe1/0/7	notconnect	1	auto	auto	unknown
Twe1/0/8	notconnect	1	auto	auto	unknown
Twe1/0/9	notconnect	1	auto	auto	unknown
Twe1/0/10	notconnect	routed	auto	auto	unknown
Twe1/0/11	notconnect	1	auto	10G	unknown
Twe1/0/12	notconnect	1	auto	10G	unknown
Ap1/0/1	connected	1	a-full	a-10G	App-hosting port
Ap1/0/2	connected	1	a-full	a-10G	App-hosting port

Switch Information

Switch Model: Cisco IOS XE Software, Version 17.12.03

Software: Cisco IOS Software [Dublin], Catalyst L3 Switch Software (CAT9K_IOSXE), Version 17.12.3, RELEASE SOFTWARE (fc7)

Technical Support: http://www.cisco.com/techsupport

Copyright: 1986-2024 by Cisco Systems, Inc.

Compiled: Wed 20-Mar-24 15:40 by mcpre

NIC port status

Command: [root@RS5220 fs]# ethtool ens4f0

Settings for ens4f0:

Supported ports: [ FIBRE ]

Supported link modes: 10000baseT/Full

Supported pause frame use: Symmetric Receive-only

Supports auto-negotiation: No

Supported FEC modes: Not reported

Advertised link modes: 10000baseT/Full

Advertised pause frame use: No

Advertised auto-negotiation: No

Advertised FEC modes: Not reported

Speed: 10000Mb/s

Duplex: Full

Auto-negotiation: off

Port: Direct Attach Copper

PHYAD: 0

Transceiver: internal

Supports Wake-on: d

Wake-on: d

Current message level: 0x0000000f (15)

drv probe link timer

Link detected: yes

Command: [root@RS5220 fs]# ethtool ens4f1

Settings for ens4f1:

Supported ports: [ FIBRE ]

Supported link modes: 10000baseT/Full

Supported pause frame use: Symmetric Receive-only

Supports auto-negotiation: No

Supported FEC modes: Not reported

Advertised link modes: 10000baseT/Full

Advertised pause frame use: No

Advertised auto-negotiation: No

Advertised FEC modes: Not reported

Speed: 10000Mb/s

Duplex: Full

Auto-negotiation: off

Port: Direct Attach Copper

PHYAD: 0

Transceiver: internal

Supports Wake-on: d

Wake-on: d

Current message level: 0x0000000f (15)

drv probe link timer

Link detected: yes

Module basic information from switch

Command: Switch#show idprom interface twentyFiveGigE 1/0/1 detail

General SFP Information

Identifier: SFP/SFP+

Ext.Identifier: SFP function is defined by two-wire interface ID only

Connector: Copper pigtail

Transceiver: 10/40GE Comp code: Unknown

SONET Comp code: Unknown

GE Comp code: Unknown

Link length: Unknown

Technology: Passive cable

Media: Unknown

Speed: Unknown

Encoding: Unknown

BR Nominal: 10300 Mbps

Length(9um)-km: GBIC does not support single mode fibre

Length(9um): GBIC does not support single mode fibre

Length(50um): GBIC does not support 50 micron multi mode OM2 fibre

Length(62.5um): GBIC does not support 62.5 micron multi mode OM1 fibre

Length(Copper): 20 m

Vendor Name: FS

Vendor Part Number: SFP-10G-PC02

Vendor Revision: 0x50 0x200x200x20

Vendor Serial Number: A2403122821-2

Wavelength: 256.00 nm

CC_BASE: 0x5F

Extended ID Fields

Options: 0x00 0x00

BR, max: 0x00

BR, min: 0x00

Date code: 240511

Diag monitoring: Implemented

Internally calibrated: No

Exeternally calibrated: No

Rx.Power measurement: OMA

Address Change: Not Required

CC EXT: 0x66

Other Information

Chk for link status: 00

Flow control Receive: ON

Flow control Send: Off

Administrative Speed: 10000

Administrative Duplex: full

Operational Speed: 10000

Operational Duplex: full

SEEPROM contents (hex)

0x00: 03 04 21 00 00 00 00 00 04 00 00 00 67 00 00 00

0x10: 00 00 02 00 46 53 20 20 20 20 20 20 20 20 20 20

0x20: 20 20 20 20 00 00 40 20 53 46 50 2D 31 30 47 2D

0x30: 50 43 30 32 20 20 20 20 50 20 20 20 01 00 00 5F

0x40: 00 00 00 00 41 32 34 30 33 31 32 32 38 32 31 2D

0x50: 32 20 20 20 32 34 30 35 31 31 20 20 00 00 00 66

0x60: 81 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00

0x70: 00 00 00 00 00 00 00 00 00 00 00 00 FF AE E6 46

Module basic information from switch

Command: Switch#show idprom interface twentyFiveGigE 1/0/2 detail

General SFP Information

Identifier: SFP/SFP+

Ext.Identifier: SFP function is defined by two-wire interface ID only

Connector: Copper pigtail

Transceiver: 10/40GE Comp code: Unknown

SONET Comp code: Unknown

GE Comp code: Unknown

Link length: Unknown

Technology: Passive cable

Media: Unknown

Speed: Unknown

Encoding: Unknown

BR Nominal: 10300 Mbps

Length(9um)-km: GBIC does not support single mode fibre

Length(9um): GBIC does not support single mode fibre

Length(50um): GBIC does not support 50 micron multi mode OM2 fibre

Length(62.5um): GBIC does not support 62.5 micron multi mode OM1 fibre

Length(Copper): 20 m

Vendor Name: FS

Vendor Part Number: SFP-10G-PC02

Vendor Revision: 0x50 0x200x200x20

Vendor Serial Number: A2403122821-1

Wavelength: 256.00 nm

CC BASE: 0x5F

Extended ID Fields

Options: 0x00 0x00

BR, max: 0x00

BR, min: 0x00

Date code: 240511

Diag monitoring: Implemented

Internally calibrated: No

Exeternally calibrated: No

Rx.Power measurement: OMA

Address Change: Not Required

CC EXT: 0x65

Other Information

Chk for link status: 00

Flow control Receive: ON

Flow control Send: Off

Administrative Speed: 10000

Administrative Duplex: full

Operational Speed: 10000

Operational Duplex: full

SEEPROM contents (hex)

0x00: 03 04 21 00 00 00 00 00 04 00 00 00 67 00 00 00

0x10: 00 00 02 00 46 53 20 20 20 20 20 20 20 20 20 20

0x20: 20 20 20 20 00 00 40 20 53 46 50 2D 31 30 47 2D

0x30: 50 43 30 32 20 20 20 20 50 20 20 20 01 00 00 5F

0x40: 00 00 00 00 41 32 34 30 33 31 32 32 38 32 31 2D

0x50: 31 20 20 20 32 34 30 35 31 31 20 20 00 00 00 65

0x60: 81 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00

0x70: 00 00 00 00 00 00 00 00 00 00 00 00 FF AE E6 46

Module basic information from NIC

Command: [root@RS5220 fs]# ethtool -m ens4f0

General SFP Information

Identifier: 0x03 (SFP)

Extended identifier: 0x04 (GBIC/SFP defined by 2-wire interface ID)

Connector: 0x21 (Copper pigtail)

Transceiver codes: 0x00 0x00 0x00 0x00 0x00 0x04 0x00 0x00 0x00

Transceiver type: Passive Cable

Encoding: 0x06 (64B/66B)

BR, Nominal: 10300MBd

Rate identifier: 0km

Length (SMF,km): 0x00 (unspecified)

Length (SMF): 0m

Length (50um): 0m

Length (62.5um): 0m

Length (Copper): 2m

Length (OM3): 0m

Passive Cu cmplnce.: 0x01 (SFF-8431 appendix E) [SFF-8472 rev10.4 only]

Vendor name: FS

Vendor OUI: 64:9d:99

Vendor PN: SFP-10G-PC02

Vendor rev: D

Option values: 0x00 0x12

Option: RX_LOS implemented

Option: TX_DISABLE implemented

BR margin, max: 0%

BR margin, min: 0%

Vendor SN: A2403123681-1

Date code: 240511

Command: [root@RS5220 fs]# ethtool -m ens4f1

General SFP Information

Identifier: 0x03 (SFP)

Extended identifier: 0x04 (GBIC/SFP defined by 2-wire interface ID)

Connector: 0x21 (Copper pigtail)

Transceiver codes: 0x00 0x00 0x00 0x00 0x00 0x04 0x00 0x00 0x00

Transceiver type: Passive Cable

Encoding: 0x06 (64B/66B)

BR, Nominal: 10300MBd

Rate identifier: 0km

Length (SMF,km): 0x00 (unspecified)

Length (SMF): 0m

Length (50um): 0m

Length (62.5um): 0m

Length (Copper): 2m

Length (OM3): 0m

Passive Cu cmplnce.: 0x01 (SFF-8431 appendix E) [SFF-8472 rev10.4 only]

Vendor name: FS

Vendor OUI: 64:9d:99

Vendor PN: SFP-10G-PC02

Vendor rev: D

Option values: 0x00 0x12

Option: RX_LOS implemented

Option: TX_DISABLE implemented

BR margin, max: 0%

BR margin, min: 0%

Vendor SN: A2403123681-2

Date code: 240511

Test Conclusion

After completing the above test content, all the test information should be copied and pasted into a TXT document.

Google Docs
Google Drive
Download [pdf]

File Info : application/pdf, 9 Pages, 1.11MB

sfp-10g-pcxxx-test-report-cisco

Related Documents

	FS SFP-10G-T-100 Transceiver Test Report for Cisco Compatibility Comprehensive test report for the FS SFP-10G-T-100 transceiver, detailing its performance and compatibility with Cisco networking equipment, including test scenarios, equipment, and results.
	FS SFP-10G-T-30 Transceiver Test Report for Cisco Compatibility This document presents the comprehensive test results for the FS SFP-10G-T-30 transceiver, verifying its performance and compatibility with Cisco networking environments. It covers test purpose, equipment used, test scenarios, and detailed results.
	FS SFP-10GLR-31 Transceiver Test Report for Cisco This document presents a comprehensive test report for the FS SFP-10GLR-31 transceiver, detailing its performance, compatibility, and diagnostic monitoring results when tested with Cisco equipment.
	FS SFP-10G-T-30 Transceiver Test Report for Arista Compatibility This document presents a comprehensive test report for the FS SFP-10G-T-30 transceiver module, detailing its performance and compatibility when used with Arista networking equipment. It outlines the test purpose, methodology, equipment utilized, and the conclusive test results.
	SFP-10GSR-85 Transceiver Test Report (Cisco Compatible) Detailed test report for the FS SFP-10GSR-85 10GBASE-SR transceiver module, including test purpose, equipment used, test scenarios, results, and Digital Diagnostic Monitoring (DDM) data. Verified for compatibility with Cisco equipment.
	FS SFP-10G-T-80 Transceiver Test Report for Cisco Compatibility This test report details the performance and compatibility testing of the FS SFP-10G-T-80 transceiver module with Cisco equipment, covering test purpose, results, equipment used, and detailed data.
	FS SFP-10G-T-80 Transceiver Test Report for Arista This document details the test report for the FS SFP-10G-T-80 transceiver, specifically tested for compatibility with Arista equipment. It covers test purpose, results summary, equipment used, test data including scenario and results, and verification of NIC port status and module basic information.
	SFP-1G34-BX10 Transceiver Test Report for Cisco Compatibility Detailed test report for the FS SFP-1G34-BX10 transceiver, verifying its compatibility and performance with Cisco switches. Includes test purpose, results, equipment, scenario, and DDM information.