Wi-Tek PoE Extender Quick Installation Guide

1. Packing Content

• 1 x PoE Extender
• 1 x Quick Installation Guide

2. Appearance Overview

WI-PE31E

Ports: 1 x 100Mbps PoE+ Input, 2 x 100Mbps PoE+ Output

DC Input: 37-57V

DIP Switch:

• Extend: On: Transmission up to 250m (rate limited to 10Mbps); Off: Transmission up to 100m (rate 100Mbps).

LED Indicators:

• PWR: On (Power normal), Off (Power off/failed).
• Link: On (Port link up), Blinking (Data TX/RX), Off (Port link down).
• PoE: On (PoE working), Off (PoE not working).

WI-PE31G

Ports: 1 x 1000Mbps PoE+ Input, 2 x 1000Mbps PoE+ Output

DC Input: 37-57V

DIP Switch:

• Extend: On: Transmission up to 250m (rate limited to 10Mbps); Off: Transmission up to 100m (rate 1000Mbps).

LED Indicators:

• PWR: On (Power normal), Off (Power off/failed).
• Link: On (Port link up), Blinking (Data TX/RX), Off (Port link down).
• PoE: On (PoE working), Off (PoE not working).

WI-PE51G

Ports: 1 x 100/1000Mbps 802.3af/at/bt Input, 4 x 100/1000Mbps PoE+ Output

DC Input: 37-57V

DIP Switch:

• VLAN: On (VLAN mode enabled), Off (VLAN mode disabled).
• Extend: On (Extend mode enabled), Off (Extend mode disabled).

LED Indicators:

• P: On (Device power on normal), Off (Device power off/failed).
• Link: On (Port link up), Blinking (Data TX/RX), Off (Port link down).
• PoE: On (PoE working), Off (PoE not working).
• V: On (VLAN mode enabled), Off (VLAN mode disabled).
• E: On (Extend mode enabled), Off (Extend mode disabled).

WI-PE21E

Ports: 1 x 100/1000Mbps PoE+ Input, 1 x 100/1000Mbps PoE+ Output

DC Input: 37-57V

DIP Switch:

• VLAN: On (VLAN mode enabled), Off (VLAN mode disabled).
• Extend: On (Extend mode enabled), Off (Extend mode disabled).

LED Indicators:

• Speed: On (Negotiate speed 1000Mbps), Off (Negotiate speed 10/100Mbps).
• Link: On (Port link up), Blinking (Data TX/RX), Off (Port link down).
• PoE: On (PoE working), Off (PoE not working).
• V: On (VLAN mode enabled), Off (VLAN mode disabled).
• E: On (Extend mode enabled), Off (Extend mode disabled).

WI-PE21G

Ports: 1 x 10/100Mbps Hi-PoE Input, 1 x 10/100Mbps Uplink, 4 x 10/100Mbps PoE+ Output

DC Input: 37-57V

DIP Switch:

• VLAN: On (VLAN mode enabled), Off (VLAN mode disabled).
• Extend: On (Extend mode enabled), Off (Extend mode disabled).

LED Indicators:

• P: On (Device power on normal), Off (Device power off/failed).
• Link: On (Port link up), Blinking (Data TX/RX), Off (Port link down).
• PoE: On (PoE working), Off (PoE not working).
• V: On (VLAN mode enabled), Off (VLAN mode disabled).
• E: On (Extend mode enabled), Off (Extend mode disabled).

3. Installation

Desktop Installation

Place the PoE extender on a flat, stable surface.

Wall-mount Installation

The device can also be mounted on a wall using appropriate hardware (not included).

4. Network Application

This section illustrates a typical networking solution using the WI-PE31E.

Installation Steps:

1. Connect the first PoE extender to a PoE port on a switch compatible with 802.3af/at/bt, or connect a DC adapter for power.
2. Connect the second PoE extender to the first PoE extender via its PoE input port.
3. Connect an IP camera or other PoE device to the second PoE extender via its PoE output port.

Note: It is recommended not to use more than 4 PoE extenders in a single chain.

Diagram Description: The diagram shows a network setup where a PoE switch connects to a series of PoE extenders. The first extender receives power and data from the switch. Subsequent extenders are connected in series, extending the reach. The final extender powers an IP camera. The diagram indicates that data and power can be transmitted up to 100 meters between extenders in the standard mode, and up to 250 meters in the extended mode (with a reduced speed of 10Mbps).

Warranty Information

Warranty Terms:

• If the product defects within three months after purchase, a new product of the same model will be provided.
• If the product defects within the three-year warranty period, professional maintenance service will be provided.

Requirements: Proof of purchase and a complete product serial number are required for warranty service.

Exclusions: The limited warranty does not cover defects caused by natural disasters, water damage, extreme thermal or environmental conditions, sticker damage, or loss of the warranty card.

Warranty Card Fields:

• Username
• Address
• Telephone No.
• Purchase Shop
• Purchase Address
• Product Model No.
• Purchase Time
• Serial No.
• Dealer Signature

Contact and Support

Company: Wireless-Tek Technology Limited

Address: Biaofang Technology Building 402, Bao'an street, Baoan District, Shenzhen City, Guangdong, China

Website: www.wireless-tek.com

Tel: 86-0755-32811290

Email: sales@wireless-tek.com

Technical Support Email: tech@wireless-tek.com

Certifications: CE, FC, ROHS