TOUGHPOWER GT 1200W / 1000W

Warnings and Cautions

• Do not unplug the AC power cord when the power supply is in use. Doing so may cause damage to your components.
• Do not place the power supply in high humidity and /or temperature environment.
• High voltages exist in the power supply. Do not open the power supply case unless you are an authorized service technician or electrician. Doing so will void the warranty.
• The power supply should be powered by the source indicated on the rating label.
• Make sure all cables are plugged in properly. Loose and improper connections would damage the power supply and your system.
• Please use only genuine Thermaltake modular cables with Thermaltake power supply models. Third-party cables might not be compatible and could cause serious damage to your system and power supply. The warranty is voided with the use of third-party cables.
• All warranties and guarantees will be voided, if failure to comply with any of the warnings and cautions covered in this label.

Components Check

• TOUGHPOWER GT power supply unit
• AC power cord
• User manual
• Mounting screws x 4
• Cable straps x 4

Power Connector Introduction

Output Specification

1200W Model

Continuous Power: 1200W

AC INPUT: Input Voltage: 100 - 240Vac ; Input Current: 15 - 10A ; Frequency: 50 - 60Hz

DC OUTPUT:

1000W Model

Continuous Power: 1000W

AC INPUT: Input Voltage: 100 - 240Vac ; Input Current: 15 - 10A ; Frequency: 50 - 60Hz

DC OUTPUT:

Installation Steps

Note: Make sure that your system is turned off and unplugged. Disconnect the AC power cord from your old power supply.

1. Open your computer chassis; please refer to the instruction manual provided with your chassis.
2. Install the PSU into the case with the four screws provided.
3. If your motherboard requires a 24pin Main Power connector, please connect the 24pin Main Power connector to the motherboard.
4. For motherboards requiring a 4pin ATX 12V(CPU) connector, detach a 4pin connector from the 4+4pin ATX 12V connector and connect it. (Either 4pin from the 4+4pin connector will work)
5. For motherboards requiring a single 8pin EPS connector, use the 4+4pin connector from the power supply.
6. Connect other peripheral power connectors to devices such as hard drives, optical drives, etc.
7. If your graphic card requires PCI-E power connector, please connect the corresponding PCI-E connector as instructed by your graphic card's user manual. Note: the power supply utilizes a unique 6+2pin PCI-E connector that can be used as an 8pin or 6pin connector. To use it as a 6pin connector, detach the 2pin part from the 6+2pin connector.
8. Close your computer case and connect the AC power cord to the power supply AC inlet.
9. Attention! When Smart Zero Fan System is turned on, the fan will not operate until the power supply reaches approximately 40% of rated load; it is normal if the fan does not operate when the computer is at a low working load.

Protection Features

Over Voltage Protection

• +3.3V: 3.76~4.3V
• +5V: 5.74~7.0V
• +12V: 13.4~15.6V

Under Voltage Protection

• +3.3V: 2.0 ~ 2.83V
• +5V: 3.15 ~ 4.47V
• +12V: 8.1 ~ 10.5V

Over Current Protection

Over Power Protection

The power supply shall be shut down and latch off, if the wattage of the power supply is 110% ~ 180% over continuous power.

Over Temperature Protection

Protection temperature is 50 ~ 65 °C (at 115V and full load).

Short Circuit Protection

Activated when any DC rails short circuited.

EMI & Safety

TOUGHPOWER GT 1200W / 1000W

CB, FCC, cTUVus, CE, UKCA, ICES, TUV, LVD, RCM, BSMI and S-mark certified.

Environments

• Operating Temperature: +0°C to +40°C
• Humidity: 5% to 85% (non-condensing)
• MTBF: > 100,000 hours

Troubleshooting

If the power supply fails to function properly, please follow the troubleshooting guide before application for service:

1. Is the power cord plugged properly into electrical outlet and into the power supply AC inlet?
2. Please make sure the I/O switch on the power supply is switched to I position.
3. Please make sure all power connectors are properly connected to all the devices.
4. If connected to a UPS unit, is the UPS on and plugged in?

If the power supply is still unable to function properly after following the above instruction, please contact your local store or Tt branch office for after sales service. You may also refer to Thermaltake's website for more technical support: thermaltake.com