Mimaki CG-100/130AR Installation Instructions for the Legs
Introduction
This manual explains how to assemble the legs with the main unit. Be sure to read this manual before assembling. You can also use your smartphone to scan the QR code below and view the 3D Instruction while assembling the product.
? Be sure to assemble with two or more people.
Accessories
If there is a shortage of parts or a problem, please contact your local distributor or MIMAKI sales office.
- Leg x2
- Caster holder x2
- Leg stay x1
- Base plate S x2
- Roll holder x2
- Roll bar x2
- Roll stay Right x1
- Roll stay Left x1
- Hexagonal wrench (4mm) x1
- Tightening pipe x1
- Screws (M5x25) x4
- Screws (M5x15) x14
- Screws (M5x16) x4
How to tighten the screws
1. Use hex wrench to temporarily tighten the screws (just tighten lightly).
[Diagram: A hex wrench is shown being used to lightly tighten a screw.]
2. Push the hex wrench into the tightening pipe and retighten the screw.
[Diagram: A hex wrench is shown inserted into a tightening pipe, used to retighten a screw.]
Instruction
1. Turn the Leg upside down
Turn the Leg upside down to make it stand on its own by using the cushioning material (upper side) in which the main body was packed.
- Assemble the right and left legs.
[Diagram: A leg is shown being turned upside down and resting on cushioning material.]
2. Fix the Caster holder to the Leg
Secure it with the 3 screws (M5x15).
- Assemble the right and left legs.
[Diagram: A caster holder is shown being secured to a leg with screws.]
3. Remove cushioning material and turn legs upright
Remove the cushioning material and turn the legs back in their original direction.
4. Turn the casters inward
Turn the casters inward.
[Diagram: Shows casters being turned inward. Two states are depicted: 'OK' (correct orientation) and 'No good' (incorrect orientation).]
5. Use cushioning materials to stand legs
Use the cushioning materials (upper side) again to make the legs (Right and Left) stand on their own.
- Push the cushioning material until it touches the legs.
- Push the cushioning material until it touches the floor.
[Diagram: Shows cushioning material being used to support the legs (Right and Left) so they stand on their own.]
6. Attach the Base plate S to the Leg
Fix the base plate to the leg with 2 screws (M5x15) while pushing it in the direction indicated by arrow.
- Assemble the right and left legs.
? Pay attention to the mounting direction.
[Diagram: Shows a base plate being attached to a leg with screws. An inset highlights pushing the base plate in the direction indicated by an arrow.]
7. Attach the screws (M5x15) with make a gap between
- Assemble the right and left legs.
[Diagram: Shows screws being attached to the legs, creating a gap between components. An inset highlights the 'Gap'.]
? Pay attention to the installation position.
8. Attach the Leg stay to the left and right legs
- Hook the leg stay onto the screws installed in step 7.
- Tighten the screw temporarily (just tighten lightly).
[Diagram: Shows a leg stay being hooked onto screws from a previous step and then tightened temporarily.]
? Attach the leg stay so that the openings of the left and right legs are on the inside.
9. Lock the casters
[Diagram: Shows casters being locked.]
10. Mount the Main unit on the legs
- Align the protruding part of the leg with the hole on the bottom of the main unit (the mark on the side of the main unit is a guide) and insert.
- Make sure that the rubber foot on the bottom of the unit is set on the leg.
- Set the other side in the same way.
[Diagram: Illustrates mounting the main unit onto the legs. Details highlight the 'Rubber Foot', 'Hole', and 'Protrusion' for alignment.]
? The unit should be lifted by two or more people.
11. Push the main unit to the front side and fix it
Push the main unit to the front side and fix it to the leg with 2 screws (M5x16).
- Push the main unit toward the front side until there is no gap between the protrusion on the rear side of the leg and the insertion hole on the bottom of the main unit and secure it.
- Set the other side in the same way.
[Diagram: Shows the main unit being pushed to the front side and fixed to the leg with screws. An inset illustrates ensuring 'No gap'.]
12. Remove cushioning materials
[Diagram: Shows cushioning materials being removed.]
13. Attach the Roll stay right to the leg
Secure it with 2 screws (M5x25).
- For installation on the front side of the main unit: Attach the roll stay right to the left side when viewed from the front of the main unit.
- For installation on the back side of the main unit: Attach the roll stay right to the left side when viewed from the back of the main unit.
[Diagram: Shows the right roll stay being secured to a leg with screws.]
? The roll stay can be installed to either the front or the back of the main unit.
14. Attach the Roll stay left to the opposite leg
Secure it with 2 screws (M5x25).
[Diagram: Shows the left roll stay being secured to the opposite leg with screws.]
15. Attach the Roll holders on the Roll bar
Attach the roll holders to the roll bar from the side with no stopper to make the flange of the roll holders face each other.
[Diagram: Shows roll holders being attached to the roll bar. An inset shows the 'Stopper (screw)'.]
16. Place the roll bar on the roll stay
Hold the side with the stopper on the roll bar in your left hand and place it on the roll stay.
[Diagram: Shows the roll bar being placed on the roll stay.]
17. Fully tighten the screws on the leg stay
[Diagram: Shows screws on the leg stay being fully tightened.]
? Turn the roll bar manually to ensure it rotates smoothly. If it gets stuck or has trouble rotating, loosen the screws that have been tightened, adjust the left and right legs so that they are parallel, and then tighten the screws.
