Whirlpool Electric Washer/Dryer

DIMENSIONS

For each arrangement, consider allowing more space for ease of installation and servicing, spacing for companion appliances and clearances for walls, doors, and floor moldings. Space must be large enough to allow door to fully open. Add spacing on all sides of dryer to reduce noise transfer. If a closet door or louvered door is installed, top and bottom air openings in door are required.

27" Model

Side view:

• Height: 65³/₄" (1670 mm)
• Width: 27¼" (692 mm)
• Depth: 32⅛" (816 mm)
• Drain hose connection height: 32" (813 mm)
• Back view depth: 11" (279 mm)
• Overall depth (back to front): 35¼" (895 mm)
• Overall height: 71¾" (1822 mm)
• Overall width: 26" (660 mm)

Back view:

• Depth: 27¼" (692 mm)
• Height: 71¾" (1822 mm)
• Width: 26½" (673 mm)
• Drain connection height: 14" (356 mm)
• Bottom clearance: 5" (127 mm)
• Top clearance: 1" (25 mm)
• Side clearance: 1" (25 mm)

Recommended installation clearances:

Companion appliance spacing should also be considered.

Side clearances: 1"/0" (25 mm/0 mm)

Front/Back/Top clearances: 1" (25 mm) (Closet), 5" (127 mm)

NOTE: Most installations require a minimum of 6" (152 mm) clearance behind dryer for exhaust vent with elbow. See "Venting Requirements."

24" Model

Side view:

• Height: 65³/₄" (1670 mm)
• Width: 26⁷/₈" (683 mm)
• Depth: 30³/₄" (781 mm)
• Drain hose connection height: 37" (940 mm)
• Back view depth: 11½" (292 mm)
• Overall depth (back to front): 34¼" (870 mm)
• Overall height: 70¾" (1797 mm)
• Overall width: 20½" (521 mm)

Back view:

• Depth: 23⁷/₈" (606 mm)
• Height: 70¾" (1797 mm)
• Width: 27½" (699 mm)
• Drain connection height: 14" (356 mm)
• Bottom clearance: 5" (127 mm)
• Top clearance: 1" (25 mm)
• Side clearance: 1" (25 mm)

Recommended installation clearances:

Companion appliance spacing should also be considered.

Side clearances: 1"/0" (25 mm/0 mm)

Front/Back/Top clearances: 1" (25 mm) (Closet), 5" (127 mm)

NOTE: Most installations require a minimum of 6" (152 mm) clearance behind dryer for exhaust vent with elbow. See "Venting Requirements.”

Drain System

Drain system can be installed using a floor drain, wall standpipe, floor standpipe, or laundry tub. Select method you need.

Floor standpipe drain system

• Minimum diameter for a standpipe drain: 2" (51 mm).
• Minimum carry-away capacity: 17 gal. (64 L) per minute.
• Top of standpipe must be at least 39" (991 mm) high; install no higher than 96" (2.4 m) from bottom of washer/dryer.
• If you must install higher than 96" (2.4 m), you will need a sump pump system.

Floor drain system

Floor drain system requires a Siphon Break Kit (Part Number 285834), 2 Connector Kits (Part Number 285385), and an Extension Drain Hose (Part Number 285863) that may be purchased separately. To order, please see toll-free phone numbers in your Use and Care Guide. Minimum siphon break: 28" (710 mm) from bottom of washer/dryer. (Additional hoses may be needed.)

Wall standpipe drain system

See requirements for floor standpipe drain system.

Laundry tub drain system

• Minimum capacity: 20 gal. (76 L).
• Top of laundry tub must be at least 39" (991 mm) above floor on 27" models, or 34" (864 mm) above floor on 24" models; install no higher than 96" (2.4 m) from bottom of washer/dryer.
• IMPORTANT: To avoid siphoning, no more than 4.5" (114 mm) of drain hose should be inside standpipe or below the top of wash tub. Secure drain hose with shipping strap or plastic strap.

INSTALLATION REQUIREMENTS

ELECTRICAL REQUIREMENTS

• 120 Volt, 60 Hz, AC only, 15- or 20- amp fused electrical supply is required. A time-delay fuse or circuit breaker is recommended. It is also recommended that a separate circuit serving only this dryer be provided.
• It is your responsibility to supply the required 3- or 4-wire, single phase, 120/240 volt, 60 Hz, AC only electrical supply (or 3- or 4-wire, 120/208 volt electrical supply, if specified on the serial/rating plate) on a separate 30-amp circuit, fused on both sides of the line. A time-delay fuse or circuit breaker is recommended. Connect to an individual branch circuit. Do not have a fuse in the neutral or grounding circuit.
• Do not use an extension cord.

WATER (STEAM MODELS ONLY) REQUIREMENTS

The machine must be connected to the cold water faucet using new inlet hoses. Do not use old hoses. Do not overtighten. Damage to the coupling can result.

VENTING REQUIREMENTS

• Exhaust venting: Exhaust your dryer to the outside. 4" (102 mm) diameter vent is required. Rigid or flexible metal exhaust vent must be used. Do not use plastic or metal foil vet. Exhaust hood must be at least 12" (305 mm) from the ground or any object that may be in the path of the exhaust.
• WARNING: To reduce the risk of fire, this dryer MUST BE EXHAUSTED OUTDOORS.
• Only a 4" (102 mm) heavy metal exhaust vent and clamps may be used.
• Do not use plastic or metal foil vent.

Determine vent length and elbows needed for best drying performance:

• Use following Vent System Chart to determine type of vent material and hood combinations acceptable to use.
• NOTE: Do not use vent runs longer than those specified in Vent System Chart. Exhaust systems longer than those specified will: Shorten life of dryer. Reduce performance, resulting in longer drying times and increased energy usage.
• The Vent System Charts provide venting requirements that will help achieve best drying performance.

Exhaust hoods:

Recommended Styles: Must be at least 12" (305 mm) from ground or any object that may obstruct exhaust (such as flowers, rocks, bushes, or snow).

Louvered Hood

Acceptable Style:

Box Hood

Angled Hood

Vent System Chart

NOTE: Bottom exhaust installations have a 90° turn inside the dryer. To determine maximum exhaust length, add one 90° turn to the charts.

Determine vent path:

• Select route that will provide straightest and most direct path outdoors.
• Plan installation to use fewest number of elbows and turns.
• When using elbows or making turns, allow as much room as possible.
• Bend vent gradually to avoid kinking.
• Use as few 90° turns as possible.