OHAUS Scout STX Balances: Quick Start Guide

UNPACKING

Carefully remove your Scout balance and each of its components from the package. Store the packaging material to ensure safe storage and future transport.

Included Components:

• Balance
• Pan
• Quick Start Guide
• Warranty Card
• AC Adapter & Plug
• Stacking & Storage Cover (not applicable for 1mg models)
• Calibration Mass (only for models up to 620g capacity)

SELECTING THE LOCATION

Place on a firm, steady surface with sufficient space. Avoid excessive air current, vibrations, heat sources, or rapid temperature changes.

PREPARATION FOR USE

1. Step 1: Release Transportation Lock

   Release the red Transportation Lock on the subplatform of the balance. Turn the pointer 90° counter-clockwise.

   Diagram showing the balance subplatform with a transportation lock pointer, indicating locked and unlocked positions.

2. Step 2: Install the Pan

   Rectangular pan: Place diagonally on sub-platform and rotate counter-clockwise until it locks. Round pan: Set straight down on subplatform.

3. Step 3: Connect Power

   Connect the AC Adapter to the balance input jack.

   Battery Installation

   Install the Four "AA" (LR6) batteries (not included) with polarity as shown in the battery compartment.

   When operating on batteries, long press the power button for up to 10 seconds to power on.

   Diagram showing the AC adapter jack and battery compartment on the balance.

4. Step 4: Level the Balance

   Level the balance before using by adjusting the feet until the level bubble is centered.

   Image showing the balance feet being adjusted to center the level bubble.

SAFETY PRECAUTIONS

CAUTION: Read all safety warnings before installing, making connections, or servicing this equipment. Failure to comply with these warnings could result in personal injury and/or property damage. Retain all instructions for future reference.

• Verify that the local AC power supply voltage is within the input voltage range printed on the AC adapter's ratings label.
• Only connect the AC adapter to a compatible grounded socket.
• Position the instrument such that the AC adapter can be easily disconnected from the socket.
• Position the power cord so that it does not pose a potential obstacle or tripping hazard.
• Operate the equipment only under ambient conditions specified in the user instructions.
• Do not operate the equipment in hazardous or explosive environments.
• Disconnect the equipment from mains power before cleaning or servicing.
• Service should only be performed by authorized personnel.

CONTROLS

Button Functions

Zero Button: Short Press: Turns the balance on. If balance is On, sets Zero. Long Press: Turns the balance Off.

Tare Button: Tare

Main Application Screen

This balance utilizes a touch-sensitive display. Touch areas and Buttons to control the balance functions.

• Indicators: Stability (*), Net (NET), Gross (G), and center of zero (>0<) indicators.
• Reference Fields: Gross, Tare.
• Result Field: Displays information that varies by application. Touch 'g' to change the unit.
• Application Buttons: Functions vary by application.

CALIBRATION

With balance turned off:

1. Step 1: Clear Pan.
2. Step 2: Turn On balance.
3. Step 3: Press Menu.
4. Step 4: Press Calibration.
5. Step 5: Choose preferred calibration method.
6. Step 6: Follow the screen instructions.

OPERATION & APPLICATIONS

The balance can be configured to operate in various Application modes. Touch the top left button in the Application area to choose the mode.

The Scout STX Balance incorporates the following Applications:

• Weighing
• Parts Counting
• Percent Weighing
• Dynamic Weighing
• Density Determination
• Check Weighing
• Display Hold
• Totalization
• Mole Weighing

Weighing Application

1. Select Weighing (this application is the default).
2. Press Tare or Zero if necessary to begin.
3. Place objects on the pan to display the weight. When stable, the '*' appears. The resulting value is displayed in the main Weighing Line in the active unit of measure.

MENU & SCREEN NAVIGATION

All menu navigation is performed by touching the display. To enter the Menu, touch Menu from any Application Home screen. The Main menu appears, with buttons for Back and Exit. Continue touching the appropriate list item to navigate to the Menu items or touch a button to change location.

Menu Options:

• Calibration: Touch to view calibration options.
• Balance Setup: Touch to view balance settings.
• Weighing Units: Touch to view weighing units.
• Data Maintenance: Touch to view data maintenance options.
• Communication: Touch to view COM Device Settings and Print Settings.
• GLP and GMP Data: Insert user data for traceability.
• Factory Reset: Touch to perform a Factory reset.
• Lockout: Touch to access the Lockout menu list.

ADDITIONAL FEATURES

Connecting the Interface

Use an optional interface connectivity kit to connect the balance either to a computer, printer, or OHAUS auxiliary display. Available interface kit accessories include: RS232, USB Host, USB Device, Ethernet, Bluetooth*.

* Interface kits may vary according to local regulations.

Weigh Below Hook

The weigh below hook is located on the reverse side of the battery cover. To use this feature, remove the red protective cover underneath for the weigh below opening.

COMPLIANCE

Compliance to the following standards is indicated by the corresponding mark on the product.

INSTRUCTION MANUAL

For more detailed information about the balance, please refer to the product instruction manual. The instruction manual can be obtained either by scanning the QR code or by going to the product page and downloading it from there.

Go to www.ohaus.com to register your product's warranty.

Product Page: http://www.ohaus.com/

QR Code: [QR Code image placeholder - QR codes are excluded from output]