MCombo Power Recliner Sofa

Purchaser's Agreement

By accepting delivery of this product, you agree not to alter, modify, or remove any safety features. You also agree to accept any retrofit kits provided by MCombo to enhance safe use.

I. Safety Guidelines

1. Mandatory

Read all safety and operating instructions thoroughly before using your MCombo product. Failure to follow these guidelines can result in personal injury or product damage and will void the warranty. Keep this manual for future reference.

2. Danger

• To prevent suffocation, keep plastic bags away from children.
• Do not allow children to play on or near the product when in use. Serious injury or death could occur if a child is under the product when it is in motion.
• Keep cords out of reach of small children and do not use where they may be a trip hazard.
• Plug directly into a wall outlet. Do not use an extension cord or adapter.
• Do not use this product if it is wet, in water, or around water or any liquid.
• Always leave the product in an upright and closed position. Keep hands and feet clear of the mechanism and all moving parts. The footrest must be completely closed before getting in or out of the product. Only the occupant should operate the product.
• Before moving or troubleshooting, unplug power cords from the outlet and secure the mechanism to prevent unexpected movement.
• Do not operate the unit until the back is installed and locked.
• Do not attempt to disassemble or repair the actuator or pump; there are no serviceable parts inside.
• Do not allow electrical cords to be pinched between moving parts or between the frame and the floor. Do not place cords under carpet or in locations where they could become worn.
• Do not attempt to disconnect the power plug by pulling the power cord. Always hold the power plug and pull it out.
• Closely supervise children and disabled persons using this product.
• To reduce the risk of head entrapment and other injuries, keep children and pets away from openings and moving parts in and around the furniture.
• This product has many moving parts; serious injury can occur if not used properly. Keep hands, fingers, and body parts away from the mechanism.
• To exit the unit safely and prevent a tripping hazard, bring the back upright and close the footrest.
• Place tables and area rugs at a distance to allow the footrest to fully extend without rubbing or interference.
• Check the condition of power supplies, electrical cords, plugs, and connectors often. Keep them away from heat sources. Never operate the unit with a damaged power supply, electrical cord, plug, or connector.
• Do not charge your device into the USB charge ports for more than 24 hours.
• Do not charge any devices over 5V/2A with the USB charge ports.
• Do not cover the USB charge ports with other heat-dissipating electronic products, as this may prevent heat dissipation and cause overheating or melting.
• Unplug the power cord immediately if you detect strange odors or fumes. Contact MCombo Customer Support.
• A seat is intended for a single occupant, not exceeding 320 pounds. Do not operate the seat with more than one occupant.
• If you give this product to someone else, include this owner's manual.

3. Warning

• Weight Capacity: 320 lbs.
• Do not use outdoors. INDOOR USE ONLY.
• To avoid tip-over, do not put your weight against the back of the product.
• Do not stand, sit, or place extra weight on the arms, back, or open footrest.
• Do not use this product if it is damaged. Do not use attachments or substitute parts.
• Avoid exposing the upholstered product to burning cigarettes or cigars, open flames, and high temperatures.

4. Symbols Information

The symbols below represent labels used on the product to identify warnings, mandatory actions, and prohibited actions. Please read and understand these symbols completely. Do not remove these labels from your product.

• Read and follow the information in the owner's manual: A book icon with an arrow.
• Weight capacity: 320 lbs: A person sitting on a sofa with "320 lbs" indicated.
• Do not connect an extension cord to the AC/DC converter: An electrical plug symbol with a line through it, connected to a converter.
• Do not place objects under the footrest when is in fully reclined position: A recliner in a reclined position with an object under the footrest, crossed out.
• Do not place objects under the headrest when the headrest of the recliner sofa is in the fully raised position.: A recliner with the headrest raised, an object under it, crossed out.
• Pinch/Crush Points Hazard: Two arrows pointing towards a gap or pinch point.
• Electrical Hazard: A lightning bolt symbol.
• Class II Equipment: A plug symbol inside a square, with another square inside.
• Indoor Use Only: A house symbol with an arrow pointing inwards.

5. Disclaimer

Read and understand this manual completely before using your MCombo Product. MCombo is not responsible for any damage or injury incurred due to improper or unsafe use, or any use that does not comply with applicable federal, state, or local laws or ordinances.

II. Assembly Instructions

Please read these instructions thoroughly before using. Do not plug in the power supply until assembly is complete. Contact MCombo Customer Support immediately if anything is missing or damaged.

1. Product Parameters

2. Part List

Use MCombo parts only for all replacements.

Box 1 of 5

• A Left Base x1

Box 2 of 5

• B Right Base x1

Box 3 of 5

• C Left Backrest x1
• D Right Backrest x1

Box 4 of 5

• E Left Armrest x1
• F Right Armrest x1

Box 5 of 5

• G Storage Console x1
• H Console Backrest x1

Part Box 1

• 1. Massage Remote x2
• 2. Seat Iron Sheet x2
• 3. Wrench x1
• 4. Screw & Washer x8
• 5. Power Adapter x2
• 6. Base Feet x4

Part Box 2

• 7. Seat Iron Sheet x2
• 8. Screw & Washer x4
• 9. Plastic Cover Screws x2

3. Assembly Steps

Step 1 - Bases Connection

1. Use Seat Iron Sheets (Part #7) to connect the seat bases (Part #A, #B, and #G).
2. When installing the steel sheets (Part #7), lightly tighten the screws (Part #4, #8) first. Do not lock them yet. Keep the steel sheets horizontal. Finally, tighten all screws (Part #4, #8) once all steel sheets are installed and the gap between the seats is adjusted.

Please connect the storage console first.

Diagram Description: Shows how to connect bases A, B, and G using seat iron sheets (7) and screws (4, 8). The attention box clarifies that the seat iron sheet needs to be installed on the iron frame, not under it.

Step 2 - Armrests Assembly

1. Align the brackets of the armrest with the clips of the base.
2. Push the armrest brackets firmly into the base. Listen for a "click" on each side to ensure the armrest is locked properly.

Ensure the two connections on each armrest are all inserted onto the seat tightly.

Step 3 - Backrests Assembly

1. Connect the storage console (Part #G) to the console backrest (Part #H) using plastic cover screws (Part #9).
2. Align the brackets of the backrest with the clips of the seat-back.
3. Push the backrest brackets firmly into the seat-back. Listen for a "click" on each side to ensure the backrest is locked properly.

Diagram Description: Shows connecting console backrest (H) to console (G) with screws (9). It also shows aligning backrest brackets with seat-back clips and pushing until a click. Attention boxes detail unzipping the console, aligning holes, and tightening screws for the console backrest.

Step 4 - Product Connections

1. Connect wire 'a' and wire 'b' from the backrest and seat base together (ensure they are the same color).
2. Connect wire 'c' from the back to the massage remote.

Diagram Description: Illustrates connecting wires labeled 'a', 'b', and 'c' for the massage function and power. A wiring specification section labels these connections. An attention box advises using a plastic clip to organize cords.

Step 5 - Paste Velcro

1. Place the loveseat in the reclined position.
2. Pull out the Velcro in the gap between the base and the backrest and paste it securely.

Step 6 - Final Check

1. Ensure both metal brackets on each armrest are mounted on the base. (There are two metal brackets on each side; proper insertion means the armrest engages one bracket, but pressure is distributed across both.)
2. Ensure the backrest inserts are locked to the base (pull up to check).
3. Ensure all wires are connected tightly.
4. Ensure all wires are not placed at the bottom of the rack and will not be pressed by the frame. (If wires are pressed, they can break, causing the sofa to stop working.)
5. Ensure all screws are tightened.

III. Operating Instructions

1. Operation Precautions

• Do not use an extension cord.
• Do not exceed the recommended weight limit.
• Do not use attachments not recommended by the manufacturer.
• Do not use outdoors. INDOOR USE ONLY.
• Keep dry. Do not operate in a wet or moist environment.
• Keep all cords away from heated surfaces and pinch points.
• Always leave the product in an upright and closed position when not in use.
• Periodically check the control and all power cords for visible damage.
• Do not use the footrest as a seat, or for purposes outside its intended use.
• Do not lean or apply downward force to the seat-back while in a recline position.

If you discover a problem during setup or positioning, stop and contact MCombo Customer Support immediately. Do not plug the unit into the electrical outlet until the problem is corrected, and do not attempt to fix electrical problems yourself.

2. Operation Instruction

• Seated: For a short break, no special operation is needed for a comfortable experience.
• Relaxing: When you want to relax, adjust the footrest position.
• Napping: To take a nap, adjust the backrest to the right position while raising the footrest for relaxation.
• Reading: When you want to read, adjust your sofa and explore a new word.

IV. Care and Maintenance

Your MCombo product will provide years of superior performance and satisfaction with regular care and maintenance. Follow the guidelines and cleaning procedures below.

Notice

• Do not place the product in direct sunlight, as sunlight causes fading.
• Do not smoke cigarettes while seated in or using the product.
• Avoid extreme temperature changes by arranging the product away from radiators, heat, and air vents.
• Do not use solvent-type cleaners to spot clean.
• Do not saturate fabric.
• Be careful that pet scratches may cause fabric or leather to break.

1. Fabric Care

• Inspect the fabric regularly for any pulls, tears, or gaps.
• Frequent vacuuming or light brushing with a nonmetallic, stiff bristle brush to remove dust and grime is recommended.
• For liquid spills, immediately wipe off spills with a dry or lightly dampened clean white cloth, sponge, or paper towel.

2. Faux Leather Care

• Wipe leather down regularly with a clean, dry microfiber cloth.
• For more stubborn dust, dampen the cloth with distilled water. Ensure the cloth is not soaking wet. Never let water soak into leather.
• Always use a soft cloth and never use an abrasive brush or scrubber, as this can scratch and damage the leather.

3. Electronics Care

• Inspect all wiring harnesses to ensure they are not damaged or stuck under the product.
• Keep all electronics free from moisture and temperature extremes.
• Check electrical components frequently for signs of corrosion and replace as necessary.
• Contact MCombo Customer Support if damage is present; do not fix it yourself.

4. Disposal & Recycling

Your power recliner sofa must be disposed of according to applicable local and national statutory disposal regulations. Contact your local waste disposal agency for information on proper disposal of packaging, metal/wood frame components, fabric, and electronic components.

V. Troubleshooting

The following FAQs should help you with common issues. If you are uncomfortable performing any troubleshooting steps, please contact MCombo Customer Support.

If the product does not operate properly, please contact MCombo Customer Support for help and never attempt to make any repairs or adjustments yourself.

VI. Disassembly Instruction

Notice

• Ensure the product is in a seated position and its footrest is returned to the original position.
• Please unplug the power cord before disassembling.
• Refer to the installation steps from back to front and disassemble the product in reverse order.

Step 1 - Disassemble Backrests

1. Push the metal ears of the backrest inserts outward (refer to arrow direction).
2. After unlocking the metal lugs on both sides of the backrest, hold the bottom part of the backrest and pull it vertically upward.

After unlocking the metal tabs on both sides of the backrest, pull the backrest upward.

Step 2 - Disassemble Armrests

Notice

1. You need to remove the backrest first.
2. It is best to remove the armrest with two people.
3. When lifting the armrest, be sure to hold the bottom of the armrest to avoid damaging the handrail bag and cup holder.

1. Use your knees to find a support point on the seat and press on the base with your own strength.
2. Hold the two marked positions at the bottom of the armrest and lift the armrest vertically upward.

Shake the armrest slightly to loosen the brackets, making it easier to detach from the base.

VII. Warranty

Notice

• For products beyond the limited manufacturer warranty period and scope, MCombo can also provide replacement service, but a basic charge will apply.
• The warranty applies only to MCombo products and does not include accessories or enhancements.
• Warranties are valid only in the 48 contiguous United States and are contingent upon the consumer operating the product according to the instruction manual.

CONSUMER WARRANTY LIMITATIONS AND EXCLUSIONS

All warranties begin on the date of delivery and are to the original purchaser from MCOMBO® ONLY.

MCOMBO® will replace defective parts or send replacement products provided the parts have not been subjected to misuse, abuse, or improper service by the consumer (e.g., damaged wires due to negligence or improper operation).

Exclusions also include components with damage caused by:

• Contamination
• Abuse, misuse, accident, or negligence
• Commercial use, or use other than normal
• Improper operation, maintenance, or storage

MCOMBO® will pay standard shipping rates on all warranted parts for the first year. Replacement parts can also be purchased at a discount price when the product is out of warranty.

VIII. Return/ Replacement Policy

Notice

Why we don't recommend returning the item yourself:

• Huge cost: UPS/FedEx oversize fee.
• You need to take the box to a UPS/FedEx facility.

Return/ Replacement Policy

MCOMBO®: You have 30 days from the date of purchase to return any item. Please pack the item securely in its original packaging, including all accessories and manuals. To initiate a return, contact customer service at sales@mcombo.com or 323-597-1109.

RETURN CONDITIONS

Items must be in new, unused condition with original tags attached and all original packaging and components included. Refunds will be issued in the original form of payment for the price of the item, including taxes.

NOTE

• Please keep the original packaging for returns. If unavailable, new packaging must meet UPS/FedEx size standards: (width + height) * 2 + length < 128 inches.
• Please disassemble the product before returning it to avoid oversized costs.
• Do not purchase return labels for damaged/defective products yourself.
• If you have any problems with returning the product, contact us immediately for assistance.

IX. Mcombo Customer Support

If you have any questions or suggestions, please refer to the following contact information. Mcombo will do its best to ensure you are satisfied.

• Email: sales@mcombo.com (Respond within 24 hours)
• Phone: 1-323-597-1109 (Monday-Friday, 8:00 a.m. - 4:00 p.m. PST)

Locations:

• DE: 2411 Bear Corbitt Rd STE 1, New Castle, DE, 19720
• TN: 3980 PREMIER AVE, MEMPHIS, TN, 38118
• CA: 2808 Vail Ave, Commerce, CA, 90040