MIBOXER 2 in 1 LED Controller (WiFi + 2.4G) Instruction Manual

Product Features

This product uses WiFi + Bluetooth + 2.4G wireless transmission technology, offering low power consumption and strong anti-interference capabilities. WiFi and Bluetooth connectivity enhance the network experience. When the router is disconnected, Bluetooth allows direct connection and control of equipment at close range. After network configuration using the [Tuya Smart] app, users can achieve wireless dimming, remote control, group control, scene control, timing control, music movement, biorhythm, sleep plans, wake plans, one-key execution, and automation. It also supports 2.4G remote control.

?️ Color temperature adjustable
? Dim brightness
? 2.4G RF wireless transmission technology
? WiFi wireless control, supports long-range control
? Auto-transmitting (only for remote control dimming)
? Device sharing
⚙️ Tap-to-Run & automation
⏱️ Timing setting / countdown for turning LED lights on/off
? Do not disturb mode
? Remote control, control distance up to 30m
? Smartphone app control
?️ Support for third-party voice control
? Group control
? Biorhythm
? Support music rhythm
? / ⏰ Sleep / wake up plan
? Support scene customization

Set Up Output Mode

Set up the correct output mode based on the feature of the lights. Setting method: Press the [SET] button continuously to switch output mode. Attention: the system will log out without operation within 3 seconds.

Output Mode Sheet

Indicator Color	Red Light	Green Light
Output	Single Color Mode	Dual White Mode

PUSH Dimming

Short press [PUSH] switch: Turn ON/OFF light. Long press [PUSH] switch: Stepless dimming brightness. Long press and release your finger, then repeat long pressing to increase or decrease brightness.

Compatible with these 2.4G RF Remote Controls

(Purchased separately)

FUT006
FUT007
B1/B1-B/T1
B2/T2
K1/K1-B
FUT087
FUT087-B
S1-B/S1-W
S1-G
WL-Box1

2.4G RF Remote Control Instructions

1). Linking Code Instructions

Step 1: Power off the controller for 10 seconds, then power on again, or short press the [SET] button once, or turn on the light via the [PUSH] switch.

Step 2: Short press the [I] button 3 times within 3 seconds.

Step 3: Lights blink 3 times slowly, indicating successful linking.

Warning: Linking failed if the light is not blinking slowly. Please follow the above steps again. Note: Lights that have already been linked cannot be linked again.

2). Unlinking Code Instructions

Step 1: Power off the controller for 10 seconds, then power on again, or short press the [SET] button once, or turn on the light via the [PUSH] switch.

Step 2: Short press the [I] button 5 times within 3 seconds.

Step 3: Lights blink 10 times quickly, indicating successful unlinking.

Warning: Unlinking failed if the light is not blinking quickly. Please follow the above steps again. Note: Lights that have not been linked do not need to be unlinked.

3). Auto Transmitting (2.4G RF Remote Signal)

The light can transmit remote signals to another light automatically when the distance between lights is up to 30m. The remote control distance is unlimited. Attention: All lights must be linked with the same remote.

4). PWM High Frequency / Low Frequency Switching (for remote control only)

Switch to high frequency (16KHz): Press the [OFF] button once within three seconds and then press the [ON] button 5 times. Activated successfully when the LED light flashes 2 times quickly. Switch to low frequency (250Hz): Press the [ON] button once within three seconds and then press the [OFF] button 5 times. Activated successfully when the LED light flashes 2 times slowly.

5). "Do Not Disturb" Mode

Turn on "Do Not Disturb" mode (useful in areas with frequent power failures to save energy).

2.4G RF Remote Turn On and Turn Off Instruction

Turn on "Do Not Disturb" mode: Press the [OFF] button three times within three seconds and then press the [ON] button three times. Activated successfully when the LED light flashes four times quickly.

Attention: Do not disturb mode is activated. 1. When the light is OFF status (e.g., use app or remote to turn off light): The light will remain OFF after power cycle. User must turn off and on power twice to activate the light, or use the APP/remote to activate it. 2. When the light is ON status: The light will remain ON after power cycle. User must turn off and on power once.

Turn off "Do Not Disturb" mode: Press the [ON] button three times within three seconds and then press the [OFF] button three times. Closed successfully when the LED light flashes four times slowly.

Attention: The light will always be in the "ON" status if you turn it on and off once after closing "Do Not Disturb" mode.

App Turn On and Off "Do Not Disturb" Mode

Click the light that needs to be set up or group control, then click "More", then click "Power-on behavior", and then turn on or off.

Smartphone App Control Instruction

Network Configuration (Does not support 5G router)

1. Download and Install [Tuya Smart] App

Search for [Tuya Smart] in the Apple App Store or Google Play Store, or scan the QR code to download and install the app. Please open the app and click the "Register" button to create an account for the first use. Log in directly if you already have an account.

2. Network Configuration

Connect the controller with power supply.
Confirm the indicator light is flashing quickly (2 flashes per second). If the indicator light is not in a fast flashing state, there are two ways to enter this mode: Long press the [SET] key until the indicator light flashes quickly, or power off and on the controller 3 times.
Connect your phone to your home WiFi network using the 2.4GHz frequency.
Open the homepage of the app and click the "+" button at the upper right corner of the page.
Click "Lighting" on the left side of the page, and then click "Light Source (BLE+Wi-Fi)".
Follow the app prompts to complete the configuration.

Alexa Voice Control Instruction

Please add the device into the [Tuya Smart] app (check details in page 6), then start following these steps:

Open the Alexa App.
Click "More" on the bottom right corner.
Click "Skills & Games".
Click the search icon [Search] on the top right corner.
Type "Smart life" and search.
Click the "Smart Life" skill, follow the instructions to finish configuration and start voice control.

Google Home Voice Control Instruction