PAX S920 Mobile Payment Terminal

1. Appearance Description

The PAX S920 is a mobile payment terminal with the following external features:

• Paper cover
• Paper cover handle
• Paper cutter
• Magnetic stripe card slot
• LCD display
• Power button
• PED Keypad
• IC Card slot
• Bar code label
• SAM/SIM socket cover
• USB port

The internal components include:

• SIM 1
• SIM 2/SAM 2
• SAM 1
• SD card slot

2. Installation

SAM/SIM/SD Card Installation

To install a SAM, SIM, or SD card:

1. Use a coin or screwdriver to remove the battery cover located at the bottom of the terminal.
2. Insert the SAM/SIM/SD card into the corresponding card slot.

Battery Replacement

1. Use a coin or screwdriver to remove the battery cover at the bottom of the terminal.
2. Remove the old battery by holding it and pulling it out.
3. Replace with a new battery by holding the battery connector and inserting it into the power socket, then aligning the battery within the battery compartments.

3. Instructions

Power ON/OFF

• Power On: Press and hold the ON/OFF button [power-symbol] for two seconds until the LCD backlight illuminates.
• Power Off: Press and hold the ON/OFF button [power-symbol] for two seconds until the LCD displays no image, indicating the terminal has turned off.

Magnetic Stripe Card

Insert the magnetic stripe side of the card towards the device interior and swipe it with a steady speed through the magnetic reader slot. The terminal supports bi-directional swiping.

IC Card

Insert the IC card with the chip side facing upward into the IC card slot until it reaches the bottom.

Contactless Card

Place the contactless card into the sensing area located above the LCD display.

4. Specifications

Default Specifications:

• CPU: 32-bit, ARM11
• Memory: 128MB DDR RAM, 256MB NAND Flash
• Display: 3.5-inch 240x320 pixel color TFT LCD with LED backlight and Touch Screen
• Keypad: 10 alphanumeric keys, 5 functional keys
• Magnetic Card Reader: Track 1/2/3, bi-directional swipe
• IC Card Reader: 1 user card (EMV2000 compliant)
• SAM slots: 2 SAM slots (ISO7816 compliant)
• Communication: LTE, GSM
• Peripheral Ports: 1 MicroUSB
• Printer: Thermal printer; Speed: 20 lines/sec; Paper width: 58mm; Paper roll outside diameter: 25mm
• Power Supply: Input: 100~240VAC, 50Hz/60Hz, 0.2A Max; Output: 5.0VDC, 1A
• Battery: Li-ion battery, 3350mAh, 3.6V
• Working Environment: Temperature: 0°C to 50°C (32°F to 120°F); Relative Humidity: 10% to 93% (non-condensing)
• Storage Environment: Temperature: -20°C to 70°C (-4°F to 150°F); Relative Humidity: 5% to 95% (non-condensing)
• Dimensions: 165mm × 78mm × 61mm (Length × Width × Height)
• Weight: 330g
• Optional: WiFi, Bluetooth, Single SIM slots
• Contactless Card Reader: Built-in, compliant with ISO/IEC 14443 Type A/B, Mifare®, Felica. Card sensing area is near the LCD screen.

5. Installation and Usage Tips

1. Avoid placing the terminal in direct sunlight, high temperature, moist, or dusty environments.
2. Do not allow non-professionals to repair the terminal.
3. Before inserting a card, check the IC card slot and its surroundings for any suspicious objects. If found, report to the relevant administrator.

6. Lithium Ion Battery Usage Tips

1. Charge the device indoors using the PAX charger in a cool, well-ventilated area.
2. Do not disassemble the battery.
3. Do not short-circuit the battery.
4. Keep the battery away from sunshine, smog, and dust.
5. Do not squeeze, puncture the battery, or place it in liquid or near fire.
6. Keep the device away from environments that are too hot, too cold, damp, or potentially explosive.
7. If the battery shows signs of failure, such as heating or distortion, or if it is damaged, replace it with a new battery.
8. Replace the battery if it no longer meets your requirements or if it has been in use for more than two years. Risk of explosion if the battery is replaced with an incorrect type.

FCC Regulations

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

This device has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

Caution: Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

FCC RF Exposure Information (SAR)

This device is designed and manufactured not to exceed the emission limits for exposure to radio frequency (RF) energy set by the Federal Communications Commission of the United States. During SAR testing, this device is set to transmit at its highest certified power level in all tested frequency bands and placed in positions that simulate RF exposure in usage near the body. Although the SAR is determined at the highest certified power level, the actual SAR level of the device while operating can be well below the maximum value. This is because the device is designed to operate at multiple power levels, using only the power required to reach the network. In general, the closer you are to a wireless base station antenna, the lower the power output.

The exposure standard for wireless employs a unit of measurement known as the Specific Absorption Rate, or SAR. The SAR limit set by the FCC is 1.6W/kg.

The FCC has granted an Equipment Authorization for this model device with all reported SAR levels evaluated as in compliance with the FCC RF exposure guidelines. SAR information on this model device is on file with the FCC and can be found under the Display Grant section of www.fcc.gov/oet/ea/fccid after searching on FCC ID: V5PS920LBW.

For this device, the extremity SAR is 1.275W/kg. While there may be differences between the SAR levels of various devices and at various positions, they all meet the government requirement.

Industry Canada statement

This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions:

1. this device may not cause interference, and
2. this device must accept any interference, including interference that may cause undesired operation of the device.

Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes:

1. l'appareil ne doit pas produire de brouillage, et
2. l'utilisateur de l'appareil doit accepter tout brouillage radio électrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement.

This device and its antenna(s) must not be co-located or operating in conjunction with any other antenna or transmitter, except tested built-in radios.

Cet appareil et son antenne ne doivent pas être situés ou fonctionner en conjonction avec une autre antenne ou un autre émetteur, exception faites des radios intégrées qui ont été testées.

The County Code Selection feature is disabled for products marketed in the US/ Canada.

La fonction de sélection de l'indicatif du pays est désactivée pour les produits commercialisés aux États-Unis et au Canada.

SAR warning statements:

This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body.

Déclaration d'exposition aux radiations:

Cet équipement est conforme aux limites d'exposition aux rayonnements IC établies pour un environnement non contrôlé. Cet équipement doit être installé et utilisé avec un minimum de 20 cm de distance entre la source de rayonnement et votre corps.