Westermo ᐅ Robust and Secure Industrial Networking SolutionsProduct support, user guides and software downloads ᐅ WestermoProduct support, user guides and software downloads ᐅ Westermo
User Guide for westermo models including: 3628-15102, 2AEJD-3628-15102, 2AEJD362815102, Ibex-1510 Series 50155 Wi-Fi Access Point, Ibex-1510 Series, 50155 Wi-Fi Access Point, Wi-Fi Access Point, Access Point, Point
Westermo Neratec AG 3628-15102 2AEJD-3628-15102 2AEJD362815102 3628 15102
File Info : application/pdf, 29 Pages, 4.05MB
DocumentDocumentw w w. we s t e r m o. c o m Ibex-1510 Series EN 50155 Wi-Fi Access Point Table of Contents 1. General Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 1.1. Legal Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 1.2. About This Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 1.3. Software Tools . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 1.4. License and Copyright for Included FLOSS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 2. Safety and Regulations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 2.1. Warning Levels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 2.2. Safety Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 2.3. Care Recommendations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 2.4. Product Disposal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 2.5. Compliance Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 2.5.1. Agency Approvals and Standards Compliance . . . . . . . . . . . . . . . . . . . . . . . . . . 8 2.5.2. United States - FCC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 2.5.3. Canada - IC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 2.5.3.1. How the Electronic label can be seen . . . . . . . . . . . . . . . . . . . . . . . . . . 10 2.5.4. Certified Antennas for FCC and IC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 2.5.5. Simplified Declaration of Conformity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 3. Product Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 3.1. Product Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 3.2. Available models . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 3.3. Hardware Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 3.3.1. Frontside Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 3.3.2. Interface Ports View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 3.4. Connector Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 3.4.1. Power Input Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 3.4.2. Ethernet Ports . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 3.4.3. Antenna Ports . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 3.5. LED Indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 3.6. Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 4. Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 4.1. Mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 4.2. Factory Reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 4.3. Earth connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 4.4. Connection of Cables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 4.5. Cooling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 4.6. Replacement of Product . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 5. Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 5.1. Interface Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 5.2. Type Tests and Environmental Conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 6. Abbreviations and Terms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 7. Revision Notes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28 2 Ibex-1510 Series 1. General Information 1.1. Legal Information The contents of this document are provided "as is". Except as required by applicable law, no warranties of any kind are made in relation to the accuracy and reliability or contents of this document, either expressed or implied, including but not limited to the implied warranties of merchantability and fitness for a particular purpose. Westermo reserves the right to revise this document or withdraw it at any time without prior notice. Under no circumstances shall Westermo be responsible for any loss of data or income or any special, incidental, and consequential or indirect damages howsoever caused. More information about Westermo can be found at www.westermo.com. 1.2. About This Guide This guide is intended for installation engineers and users of the Westermo products. It includes information on safety and regulations, a product description, installation instructions and technical specifications. 1.3. Software Tools Related software tools are available at https://www.westermo.com/support/productsupport. 1.4. License and Copyright for Included FLOSS This product includes software developed by third parties, including Free/Libre Open Source Software (FLOSS). The specific license terms and copyright associated with the software are included in each software package respectively. Please visit the product web page for more information. Upon request, the applicable source code will be provided. A nominal fee may be charged to cover shipping and media. Please direct any source code request to your normal sales or support channel. Ibex-1510 Series 3 2. Safety and Regulations 2.1. Warning Levels Warning signs are provided to prevent personal injuries and/or damages to the product. The following levels are used: Level of warning Description Indicates a potentially hazardous situation Consequence personal injury Possible death or major injury Consequence material damage Major damage to the product WARNING Indicates a potentially hazardous situation Minor or moderate injury Moderate damage to the product CAUTION Provides information in order to avoid misuse of the product, confusion or misunderstanding No personal injury Minor damage to the product NOTICE Used for highlighting general, but important information No personal injury Minor damage to the product NOTE Table 1. Warning levels 4 Ibex-1510 Series 2.2. Safety Information Before installation: Read this manual completely and gather all information available on the product. Make sure it is fully understood. Check that your application does not exceed the safe operating specifications for the product. SAFETY DURING INSTALLATION The product must be installed and operated by qualified service personnel and installed into an apparatus cabinet or similar, where access is restricted to service personnel only. Before energising and connecting communication cables to the product, ensure a protective earthing conductor is first connected to the protective earthing terminal (only valid for metallic housings). Westermo recommends a cross-sectional area of at least 4 mm2. Note that this product can be connected to two different power sources. Upon removal of the product, disconnect the product from the power supply and all other communication ports before disconnecting the protective earthing conductor. HAZARDOUS VOLTAGE Do not open an energised product. Hazardous voltage may occur when connected to a power supply. PROTECTIVE FUSE The power supply wiring must be sufficiently fused. The fuse must be IEC 60127 certified and rated for T1.6 A and 250 V. It must be possible to disconnect manually from the power supply. Ensure compliance to national installation regulations. This product has no internal fuse and should be connected via an external fuse for protection. POWER SUPPLY CONNECTION There are safety regulations governing the power source that can be used in conjunction with the product. Refer to chapter Interface Specifications. Ibex-1510 Series 5 RADIO PRODUCTS Observe the usage limitations of radio products at filling stations, in chemical plants, in systems with explosives or potentially explosive locations. The product may not be used in airplanes. Exercise particular caution near personal medical aids, such as pacemakers and hearing aids. Never perform work on the antenna system during a thunderstorm. To fulfill human safety, a minimum separation distance of 20 cm or more should be maintained between the antenna of the product and personnel during operation. HOT SURFACE Be aware that the surface of this product may become hot. When it is operated at high temperatures, the external surface may exceed Touch Temperature Limit according to the product's relevant electrical safety standard. CORROSIVE GASES If the product is placed in a corrosive environment, it is important that all unused connector sockets are protected with a suitable plug, in order to avoid corrosion attacks on the gold plated connector pins. CABLE TEMPERATURE RATING FOR FIELD TERMINAL WIRES There may be a requirement on the minimum temperature rating of the cable to be connected to the field wiring terminals, see chapter Interface Specifications. 6 Ibex-1510 Series 2.3. Care Recommendations Follow the care recommendations below to maintain full operation of the product and to fulfill the warranty obligations: · Do not drop, knock or shake the product. Rough handling above the specification may cause damage to internal circuit boards. · Use a dry or slightly water-damp cloth to clean the product. Do not use harsh chemicals, cleaning solvents or strong detergents. · Do not paint the product. Paint can clog the product and prevent proper operation. If the product is used in a manner not according to specification, the protection provided by the equipment may be impaired. If the product is not working properly, contact the place of purchase, the nearest Westermo distributor office or Westermo technical support. NOTE Devices not used shall be kept in the factory sealed moisture barrier bag. Open, unsealed devices should not be kept unpowered for more than 30 days. 2.4. Product Disposal This symbol means that the product shall not be treated as unsorted municipal waste when disposing of it. It needs to be handed over to an applicable collection point for recycling electrical and electronic equipment. Proper disposal of the product helps minimize hazardous substances and prevents potential negative impacts on both the environment and human health. Figure 1. WEEE symbol for treatment of product disposal 2.5. Compliance Information REGULATORY NOTICE Any changes or modifications shall be approved by the party responsible for compliance. If not, users could void the user's authority to operate the equipment. Country code and antenna gain need to be set properly for correct functionality in the installed country. Ibex-1510 Series 7 2.5.1. Agency Approvals and Standards Compliance Approvals and Standards Climate · EN 50155, class OT4 Railway applications - Electronic equipment used on rolling stock EMC · EN 50155, Railway applications - Electronic equipment used on rolling stock · EN 50121-3-2, Railway applications Electromagnetic compatibility, Part 3-2: Rolling stock Apparatus · ETSI EN 301 489-1, Electromagnetic compatibility (EMC) and Radio spectrum Matters (ERM) for radio equipment and services - Part 1: Common technical requirements · ETSI EN 301 489-17, Electromagnetic compatibility (EMC) and Radio spectrum Matters (ERM) for radio equipment - Part 17: Specific conditions for Broadband Data Transmission Systems Mechanical · EN 61373, category 1, class B (Shock and vibration) Insulation (Coordination and test) · EN 50155, Railway applications - Electronic equipment used on rolling stock Radio communication · ETSI EN 300 328, Wideband transmission systems; Data transmission equipment operating in the 2.4 GHz ISM band and using wide band modulation techniques · ETSI EN 301 893, 5 GHz RLAN · ETSI EN 300 440, 5.8GHz, Short Range Devices · IEEE802.11, Wireless LAN Medium Access Control (MAC) and Physical Layer (PHY) Specifications Safety · EN/IEC 61010-1, Safety requirements for electrical equipment for measurement, control, and laboratory use · EN 45545-2, Fire protection on railway vehicles 2.5.2. United States - FCC The enclosed product complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (i.) this product may not cause harmful interference and (ii.) this product must accept any interference received, including interference that may cause undesired operation. To satisfy FCC RF exposure requirements for mobile transmitting devices, a separation distance of 20 cm or more should be maintained between the antenna of this product and persons during operation. To ensure compliance, operations at closer distances than this are not recommended. This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. 8 Ibex-1510 Series Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. NOTE This product contains FCC ID 2AEJD-3628-15102. 2.5.3. Canada - IC This product complies with Industry Canada's license-exempt RSSs. Operation is subject to the following two conditions: · This product may not cause interference. · This product must accept any interference, including interference that may cause undesired operation of the product. Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes: · l'appareil ne doit pas produire de brouillage. · l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement. NOTE This product contains the IC Certification number 9301A-362815102. EXPOSURE TO RADIO FREQUENCY RADIATION To comply with the Canadian RF exposure compliance requirements, this device and its antenna must not be co-located or operating in conjunction with any other antenna or transmitter. To comply with the RSS 102 RF exposure compliance requirements, this equipment should be installed and operated, keeping the radiator at least 20cm or more away from the person's body. Ibex-1510 Series 9 EXPOSITION AU RAYONNEMENT RADIOFRÉQUENCE Pour se conformer aux exigences de conformité RF canadienne l'exposition, cet appareil et son antenne ne doivent pas être colocalisé ou fonctionnant en conjonction avec une autre antenne ou transmetteur. Pour se conformer aux exigences de conformité CNR 102 RF exposition, cet équipement dout être installé et utilisé en maintenant le radiateur à au moins 20cm ou plus du corps de la personne. 2.5.3.1. How the Electronic label can be seen Devices based on factory configuration do show the e-label using a web browser. The steps to access the information are: 1. Connect the Ibex-1510 via Ethernet to a PC and power them up. 2. Write at the web browser of the PC: http://192.168.1.20 or https://192.168.1.20 2.5.4. Certified Antennas for FCC and IC This radio transmitter has been approved by FCC (FCC ID:2AEJD-3628-15102) and Innovation, Science and Economic Development Canada (IC:9301A-362815102) to operate with the antenna types listed below, with the maximum permissible gain indicated. Antenna types not included in this list have a gain greater than the maximum gain indicated for any type listed are strictly prohibited for use with this device. Le présent émetteur radio a été approuvé par FCC (FCC ID:2AEJD-3628-15102) et Innovation, Sciences et Dévelopment économique Canada (IC:9301A-362815102) pour fonctionner avec les types d'antenne é numérés ci-dessous et ayant un gain admissible maximal. Les types d'antenne non inclus dans cette liste, et dont le gain est supérieur au gain maximal indiqué pour tout type figurant sur la liste, sont strictement interdits pour l'exploitation de l'émetteur. Type Omni Supplier HUBER+SUHNER Antenna Part No. 1399.35.0008 Patch Westermo ICL-5 Table 2. Certified antennas for FCC and IC Frequency (MHz) 2412 - 2462 5150 - 5250 5250 - 5350 5470 - 5725 5725 - 5850 5150 - 5250 5250 - 5350 5470 - 5725 5725 - 5850 Peak Antenna Gain (dBi) 4 6 6 6 6 4 4 4 4 10 Ibex-1510 Series 2.5.5. Simplified Declaration of Conformity Hereby, Westermo declares that this product is in compliance with applicable EU directives and UK legislations. The full declaration of conformity and other detailed information is available at www.westermo.com/support/product-support. Figure 2. The European Conformity and the UK Conformity Assessment markings Ibex-1510 Series 11 3. Product Description 3.1. Product Description The Ibex-1510 is a concurrent dual-band 802.11ax WLAN access point and client product for onboard and stationary applications. The access points provides reliable efficient high-speed data transfers, it can be used for passenger hotspot applications, remote maintenance access, data offloading or as part of a TCMS network. Power DC Supply (optional) WLAN 802.11ax Combiner 2.5GBASE-T 2.4 GHz A1 X1 Ethernet CPU PoE PD WLAN A2 802.11ax X2 2.5GBASE-T Ethernet 5 GHz Figure 3. Ibex-1510 block diagram The Westermo configuration management tool, WeConfig, can be used for discovery and basic configuration and maintenance. The configuration can be done locally or remotely via SNMP or via WebGUI/API. The status information is available in local LED status indicators, and through SNMP or WebGUI/API. The Ibex-1510 access point is designed to withstand tough onboard environmental conditions. Integrating hardware, software and network design support tools, this access point platform offers advanced capabilities, the lowest total cost of ownership and will create the most reliable and resilient networks. The access point is engineered to maintain uninterrupted data communication, even in exceptionally harsh environments. Tested and certified to withstand extreme temperatures, vibrations and shocks, these products only use industrial grade components which contributes towards a market leading mean time between failure (MTBF), maximized service life, and reduced operational and life cycle costs. 12 Ibex-1510 Series 3.2. Available models Art. no. 3628-15101 3628-15102 3628-15111 3628-15112 Model Ibex-1510-T2G2.5 EU Ibex-1510-T2G2.5 NA Ibex-1510-T2G2.5-PoE EU Ibex-1510-T2G2.5-PoE NA Table 3. List of available models Region Europe North America Europe North America 3.3. Hardware Overview PoE Port X1 X1 X1 X1 Rated voltage 24-110 VDC 24-110 VDC - 3.3.1. Frontside Overview 8 7 1 2 3 4 65 No. Description 1 2.5 Gigabit Ethernet port X2 3 Power input DC (optional)a. 5 Frontside label 7 Antenna ports A1 - A2 (2.4 GHz / 5 GHz) Table 4. Location of interface ports No. Description 2 2.5 Gigabit Ethernet port X1 (PoE) 4 Protective earth terminal 6 Warning symbol for surface temperatures above +60°C 8 Product family label Ibex-1510 Series 13 3.3.2. Interface Ports View 1 3 2 DC X1 X2 4 A1 ON PoE 5 A2 No. Description No. 1 Power input DC (optional)a. 2 3 Ethernet 2.5GBase-T ports (X1 PoE) 4 5 Antennas A1 - A2, 2.4 GHz / 5 GHz a.DC power supply not included in "PoE only" product variants Table 5. Interface ports view Description Protective earth terminal Ethernet 2.5GBase-T port X2 3.4. Connector Information 3.4.1. Power Input Connection The Ibex-1510 product variants can be equipped with a DC dual input power port that meets the following specifications. Refer also to the LED status indicators. Marking DC Position 1 2 3 4 Housing Direction +DC1 +DC2 -DC -DC Shield Description Positive terminal Positive terminal Negative terminal Negative terminal Chassis of product (ground) Table 6. M12 A-coded 4-pin male power connector according to IEC 61076-2-101 3.4.2. Ethernet Ports The product includes two Ethernet ports X1 and X2 which supports auto-negotiated 10 Mbit/s, 100 Mbit/s, 1000 Mbit/s and 2500 Mbit/s operation. Automatic MDI/MDIX crossover is supported for 10BASE-T, 100BASE-T, 1000BASE-T and 2500BASE-T operation. 14 Ibex-1510 Series Marking X1/X2 Position 1 2 3 4 5 6 7 8 Housing Direction In/Out In/Out In/Out In/Out In/Out In/Out In/Out In/Out Shield Description DA+ DADB+ DBDD+ DDDCDC+ Chassis of product (ground) Table 7. M12 X-coded 8-pin female Ethernet connector according to IEC 61076-2-109 Position 1 2 3 4 5 6 7 8 Device mode A +DC +DC -DC -DC Device mode B -DC -DC +DC +DC Table 8. Ethernet PoE connection on X1 NOTE If the Ethernet function is not used, the protective dust cap which is part of the delivery must be closed to protect the interface from water or dust ingress. 3.4.3. Antenna Ports The antenna connectors are identified on the product with A1 and A2. A1 and A2 are combined antenna ports for 2.4 GHz and 5 GHz WLAN communication. At least A1 must be connected to an external WLAN antenna. The antenna configuration is made through the software interface. Ibex-1510 Series 15 NOTICE Any unused antenna ports must be properly terminated with 50 Ohm, otherwise the product might be damaged when power is applied to a non-terminated antenna port. NOTE To ensure specified IP protection, suitable QMA connectors/cables and terminations must be used. 3.5. LED Indicators DC X1 X2 ON PoE Figure 4. LED indicators LED Description DC Power status ON Operation status X1 Ethernet status for X1 port X2 Ethernet status for X2 port Table 9. LED indicators NOTE The power status LED is green if both input power sources are available. The LED lights up red if only one power input source is provided. NOTE Refer to management guide for detailed LED status indication. 16 Ibex-1510 Series 9.7 40.5 36.5 40.5 3.6. Dimensions Dimensions are stated in mm and are regardless of variants. 7 0 9 2 195.4 7.7 180 Figure 5. Dimensional drawing 66 6.7 19 20.5 24.5 25.0 111.4 Ibex-1510 Series 17 4. Installation 4.1. Mounting The product is fixed with the four fixing points located at the corners of the product. M6 screws are used for the fixation of the product. The screws are tightened with min. 3.0 Nm (fixing screw ISO 898/1, quality class 8.8). NOTICE All four specified fixing points must be used for fixing. The installation surface should be flat to have all fixing points connected to the surface. NOTE For indoor installation, consider additional protection against dust to ensure proper heat dissipation. NOTE For outdoor installation, consider additional protection against sun radiation, dust and dirt to optimize ambient temperature range. NOTE Unused connectors must be covered by a protective cap (delivered with the product), tightened to the specified torque in order to fulfill the specified ingress protection code. 18 Ibex-1510 Series 4.2. Factory Reset To reset the product into factory default settings, a reset adapter is needed which is plugged into one of the Ethernet ports X1 or X2 during startup. Art. no. 3623-0799 Description Factory Reset Plug, X-coded Factory reset procedure 1. Plug the factory reset adapter to one of the Ethernet interfaces. 2. Power the product. 3. Wait until factory reset adapter is detected. This is indicated by a solid RED ON LED. 4. Remove factory reset adapter within 15 seconds. 5. Successful initiation of the factory reset is indicated by blinking RED ON LED. 4.3. Earth connection For correct function, the earth connection at the grounding point needs to be properly connected to a solid ground. An M6 grounding screw at the housing is used for grounding. A short wire with a cross section of at least 4 mm2 shall be used. The grounding wire is set below the rip-lock washer. The nut is fixed for good reliable grounding contact. The tightening torque of the grounding nut should not exceed 10 Nm. DC X1 X2 ON PoE Figure 6. Earth connection NOTICE Do not use equipment without protective earth connection. 4.4. Connection of Cables Recommended tightening torque for the M12 connectors is 0.6 Nm. All M12 connections are screw connections. When connecting the power cable, ensure that the pins are connected correctly before tightening the power cable to the unit. Ibex-1510 Series 19 NOTE This product has no replaceable fuse and should be connected via an external fuse for protection. 4.5. Cooling This product uses convection cooling. Make sure that it is installed so that the ambient temperature is within the specified temperature range, e.g. by avoiding obstruction of the airflow around the product. It is recommended to install the product in areas where the natural convection airflow is not blocked and that there is enough spacing around the product. When operating the product at high ambient temperatures, it is recommended to mount the product to a metallic base plate to improve the heat dissipation. The base plate increases the surface to spread the heat. NOTICE Limited air flow is rising the product temperature and may lower the upper limit of the operating temperature range. NOTICE Temperature is dependent on the operational parameters, like RF output power, amount of traffic. NOTICE This product has integrated temperature sensors for monitoring the internal device temperatures. If temperature limits are exceeded, alarms are sent through the SW interface. NOTICE The operating conditions shall be ensured so that the normal operation does not cause temperature alarms. Improve installation conditions or RF parameters in case of any temperature alarms. 4.6. Replacement of Product The device cannot be repaired. In case of a malfunction, it must be replaced. Disconnect all cables and unscrew the product from the wall. Mount the replacement product and reconnect all cables, observing the instructions in Connection of Cables. 20 Ibex-1510 Series MTTR (Mean Time To Repair), i.e. time for replacement of product is: < 10 minutes. HOT SURFACE Be aware that the surface of this product may become hot. When it is operated at high temperatures, the external surface may exceed Touch Temperature Limit according to the product's relevant electrical safety standard. Ibex-1510 Series 21 5. Specifications 5.1. Interface Specifications DC, Power port Connector Rated voltage Operating voltage Rated power Rated frequency Startup current Polarity Redundant power input Conductor cross section (flexible) Cable temperature rating Shielded cable M12 A-coded male 24 to 110 VDC, Class 1 16.8 to 143 VDC 14 W DC 2 x rated current Reverse polarity protected Dual input port > 0.5 mm² (AWG 20) -40 to +70°C Not required PoE (on X1) Connector Device mode Rated voltage Operating voltage Power classification M12 X-coded female A and B 48 VDC 37 to 57 VDC Class 4 Ethernet Connector Electrical specification Data rate Duplex Transmission range Cabling Conductive chassis M12 X-coded female IEEE std 802.3 10 Mbit/s, 100 Mbit/s, 1000 Mbit/s, 2500 Mbit/s manual or auto Full or half, manual or auto Up to 100 m with CAT5e cable or better Shielded cable CAT5e or better is recommended Yes NOTE The product is to be connected to internal Ethernet networks without exiting a facility and being subjected to TNVs. 22 Ibex-1510 Series NOTICE To avoid damages on the Ethernet interfaces, ensure that the far end side of the Ethernet cable shield itself is connected to protective earth. Antenna WLAN (A1 to A2) Connector QMA female Direction Transmit and receive Cabling 50 Ohm coaxial cable and WLAN antenna required Conductive chassis Yes WLAN interfaces 2x2 MU-MIMO for 2.4 GHz and 5 GHz, 802.11a/g/n/ac/ax Access Point WLAN frequency bands 2.400 to 2.4835 GHz 5.150 to 5.350 GHz, 5.470 to 5.725 GHz, 5.725 to 5.850 GHz Transmitting powera. 2.4 GHz and 5 GHz: up to 25 dBm, per port: 22 dBm a.Max. conducted transmit power within the whole frequency range and for all data rates NOTICE Depending on the installation country there are frequency/band restrictions and output power limitations. NOTICE Unused antenna port must be terminated with 50 Ohm terminations. NOTICE To avoid damages on the antenna interfaces, ensure that the far end side of the antenna cable and/or the antenna itself is connected to protective earth. Ibex-1510 Series 23 5.2. Type Tests and Environmental Conditions Environmental phenomena ESD Fast transients Basic standard EN 61000-4-2 EN 61000-4-4 Surge EN 61000-4-5 Power frequency magnetic field Radiated RF immunity EN 61000-4-8 EN 61000-4-3 Conducted RF immunity EN 61000-4-6 Radiated RF emission Conducted RF emission EN 55032 EN 55032 Insulation resistance Dielectric strength EN 50155 EN 50155 Description Test levels Enclosure DC power port Ethernet ports Antenna ports DC power port Ethernet ports Antenna ports Enclosure Enclosure DC power port Ethernet ports Antenna ports Enclosure Contact: ±6 kV Air: ±8 kV ± 2 kV, direct coupling ± 2 kV, capacitive coupling clamp L-E: ± 1 kV, 12 , 9 µF, 1.2/50 µs L-E: ± 2 kV, 42 , 0.5 µF, 1.2/50 µs L-L: ± 1 kV, 12 , 9 µF, 1.2/50 µs L-L: ± 2 kV, 42 , 0.5 µF, 1.2/50 µs Shield-E: ± 2 kV, 2 , 1.2/50 µs 300 A/m continues, DC, 16.7 Hz, 50 Hz, 60 Hz 20 V/m, 80% AM (1kHz) at 80 MHz to 6 GHz 30 V/m, PM 200 Hz square at 380 MHz to 385 MHz 30 V/m, PM 200 Hz square at 390 MHz to 395 MHz 10 V, 80% AM (1 kHz) from 0.15 to 80 MHz Class A DC power port Ethernet ports Power port (DC) to all other ports Power port (DC) to all other ports Class A > 100 MOhm 2200 VDC, 60 s Table 10. EMC and electrical conditions 24 Ibex-1510 Series Environmental phenomena Temperatures Basic standard EN 60068-2-1 EN 60068-2-2 EN 60068-2-14 Description Operational Storage and transport Test levels -40 to +70°C (-40 to +158°F)a. -55 to +85°C (-67 to +185°F) Humidity EN 60068-2-30 Operational Storage and transport 5-95% relative humidity Altitude Operational 3000 m MTBF Vibration Shockb. IEC TR 62380 EN 60068-2-64 (random) EN 60068-2-27 Operational, endurance test Operational 424,000 hours 538,000 hours (PoE product variant only) 11.44 m/s2 random, 5 to 150 Hz, 3 x 5 h 100 m/s2, 30 ms, 3 x 6 shocks (half sine) MIL STD 810, M516.7 20 g, 11 ms, 3 x 6 shocks (saw tooth) Weight Degree of protection EN 60529 Enclosure 1450 gr IP66c. Cooling Convection Pollution degree EN 61010-1 PD2 Conformal coating type IPC-A-610 Electronic modules AR (Acrylic) a.Refer to "Safety and Regulations" chapter regarding touch temperature b.The power and Ethernet cables need to be fastened 200 mm or closer to the unit. The same recommendation applies to the Antenna cables. c.Provided all connectors are connected with IP66 cabling or fitted with protective caps (delivered with the unit) and tightened to the specified torque Table 11. Environmental and mechanical conditions Ibex-1510 Series 25 6. Abbreviations and Terms Abbreviation AM AREMA AWG CAT5e CE CPU DC EMC EN ERR ESD ETSI FCC FLOSS IEC IC ID I/O IP ISO LAN LED MIMO MTBF MTTR OPR QR RF SN SNMP TNV WebAPI WebGUI Description Amplitude Modulation American Railway Engineering and Maintenance-of-Way Association American Wire Gauge Category 5 Enhanced Cable Conformité Européenne Central Processing Unit Direct Current Electromagnetic Compatibility European Standard Error Electro Static Discharge European Telecommunications Standards Institute Federal Communication Commission Free/Libre Open Source Software International Engineering Consortium Industry Canada Identification Input / Output Ingress Protection International Standardization Organisation Local Area Network Light Emitting Diode Multiple Input, Multiple Output Mean Time between Failure Mean Time to Repair Operation Quick Response Radio Frequency Serial Number Simple Network Management Protocol Telephone Network Voltage Web Application Programming Interface Web Graphical User Interface 26 Ibex-1510 Series Abbreviation WeConfig WEEE Wi-Fi WLAN Description Westermo Configuration Tool Waste Electrical and Electronics Equipment Wireless Fidelity Wireless Local Area Network Table 12. Abbreviations and terms Ibex-1510 Series 27 7. Revision Notes Revision Rev. A Rev. B Rev. C Rev. D Date 2024-02 2024-04 2024-11 2025-01 Change description First revision Update Figure 3. Ibex-1510 block diagram and antenna ports description Add United States FCC and Canada IC compliance Add safety warning and allowed antenna types for Canada IC compliance 28 Ibex-1510 Series 6628-2220 REV. D 2025 01 @ Westermo Network Technologies AB, Sweden