Lithonia Lighting LED Canopy Fixture Installation Instructions

Important Safety Instructions

❗ WARNING: RISK OF ELECTRIC SHOCK

• Disconnect or turn off power before installation or servicing.
• Verify that supply voltage is correct by comparing it with the luminaire label information.
• Make all electrical and grounded connections in accordance with the National Electrical Code (NEC) and any applicable local code requirements.
• All wiring connections should be capped with UL approved wire connectors.

❗ CAUTION: RISK OF INJURY

• Wear gloves and safety glasses at all times when removing luminaire from carton, installing, servicing or performing maintenance.
• Avoid direct eye exposure to the light source while it is on.

❗ CAUTION: RISK OF FIRE

• Keep combustible and other materials that can burn, away from lamp/lens.
• Do not operate in close proximity to persons, combustible materials or substances affected by heat.

❗ CAUTION: RISK OF PRODUCT DAMAGE

• Never connect components under load.
• Do not mount or support these fixtures in a manner that can cut the outer jacket or damage wire insulation.
• Unless individual product specifications deem otherwise: Never connect an LED product directly to a dimmer packs, occupancy sensor, timing device, or other related control devices. LED fixtures must be powered directly off a switched circuit.
• Unless individual product specifications deem otherwise: Do not restrict fixture ventilation. Allow for some volume of airspace around the fixture. Avoid covering LED fixtures with insulation, foam, or other material that will prevent convection or cooling.
• Unless individual product specifications deem otherwise: Do not exceed fixture's maximum ambient temperature.
• Only use fixture in its intended location.
• LED products are Polarity Sensitive. Ensure proper Polarity before installation.
• Electrostatic Discharge (ESD): ESD can damage LED fixtures. Personal grounding equipment must be worn during all installation or servicing of unit.
• Do not touch individual electrical components as this can cause ESD, shorten lamp life, or alter performance.
• Some components inside the fixture may not be serviceable. In the unlikely event your unit may require service, stop using the unit immediately and contact an ABL representative for assistance.
• Changes or modifications not expressly approved by Acuity Brands Lighting could void the authority to operate the equipment.
• Always read the fixture's complete installation instructions prior to installation for any additional fixture specific warnings.

❗ WARNING: RISK OF BURN

• Allow lamp/fixture to cool before handling. Do not touch enclosure, lens or light source.
• Do not exceed maximum wattage marked on luminaire label.
• Follow all manufacturer's warnings, recommendations and restrictions including but not limited to: driver type, burning position, mounting locations/methods, replacement and recycling.
• Use only lamps that comply with ANSI standards.

FCC Compliance

This equipment has been tested and found to comply with the limits for a class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when used in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

This device complies with FCC radiation exposure limits set forth for an uncontrolled environment. This device should be installed and operated with a minimum distance of 20cm between the radiator and your body.

This equipment complies with ISED radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator and your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada's licence-exempt RSS(s). Operation is subject to the following two conditions: (1) This device may not cause interference. (2) This device must accept any interference, including interference that may cause undesired operation of the device.

5-Year Limited Warranty

Register your warranty on www.acuitybrands.com/resources/warranty. Your prompt product registration confirms your right to the protection available under the terms and conditions of your Lithonia Lighting warranty.

Failure to follow any of these instructions could void product warranties. For a complete listing of product Terms and Conditions, please visit www.acuitybrands.com. Acuity Brands Lighting, Inc. assumes no responsibilities for claims arising out of improper or careless installation or handling of its products.

Fixture Packing List

Remove fixture components and parts pack. Check to ensure all parts are included. Note: Account for small parts and destroy packing material, as these may be hazardous to children.

• 1) Fixture Housing
• 2) 5/8" 8-32 & 10-24 J-Box Mounting screws* (4)
• 3) Wire Nuts* (3)
• 4) Wire Plug* (1)
• *Contained in parts packs

Mounting Hardware and Silicone Sealant Required - Purchase Separately

Required Tools:

• Screwdriver (Phillips head)
• Wire strippers/cutters
• Pliers
• Adjustable wrench
• Teflon tape or silicone sealant (for conduit mounting)

General Installation Precautions

Turn OFF Power at fuse or circuit breaker box! ❗ CAUTION: Do not rely on wall switch alone to turn off power. Not suitable for use with motion sensors or other remote devices.

This fixture is intended for ceiling, wall or stem mount (conduit and stem not included).

Mounting Instructions

For J-Box Mounting

Refer to Figures A, B, C.

1. Loosen the screws on the front of housing and slide the housing with lens to the left to detach from top housing. (See Figure A)
2. Pull power wires all the way through the center hole on the mounting backplate. Fix the back housing to the ceiling using provided mounting screws. (See Figure B)
3. Make wiring connections using provided wire nuts. (See Figure C). Re-attach the lens housing to the mounting backplate by sliding the pins back in. Close the housing and screw down, max torque: 1.5ft-lbs (2Nm).

For Conduit Mounting

Refer to Figures A, B, C, E.

1. Loosen the screws on the front of housing and slide the housing with lens to the left to detach from top housing. (See Figure A)
2. Fix the back housing to the ceiling using provided mounting screws. (See Figure B)
3. Remove conduit plug. Feed input leads through 3/4" conduit pipe and screw pipe into fixture threading. Note: Seal thread using Teflon tape or silicone sealant.
4. Make wiring connections using provided wire nuts. (See Figure C). Re-attach the lens housing to the mounting backplate by sliding the pins back in. Close the housing and screw down, max torque: 1.5ft-lbs (2Nm). (See Figure E)

For Pendant Mounting

Refer to Figures A, B, C.

1. Loosen the screws on the front of housing and slide the housing with lens to the left to detach from top housing. (See Figure A)
2. Remove rubber wire plug from the top of fixture to expose the NPS threads.
3. Feed input leads through a 3/4" threaded conduit pipe and screw conduit pipe into fixture threading. Note: Seal thread using Teflon tape or silicone sealant.
4. Make wiring connections using provided wire nuts. (See Figure C). Re-attach the lens housing to the mounting backplate by sliding the pins back in. Close the housing and screw down, max torque: 1.5ft-lbs (2Nm).

Optional Settings

CAUTION: SWITCH CAN ONLY OPERATE WHEN POWER TO FIXTURE IS OFF. WAIT 60 SECONDS BEFORE POWERING AFTER SWITCHING.

To change settings, use a Phillips head screwdriver to remove the switch cover on the side of the fixture. (See Figure C for switch location, Figure F for settings labels).

• Lumens: Factory set to brightest sun (10,000lm). Options: Middle sun (7500lm), Dimmest sun (5000lm).
• Color Temperature (CCT): Factory set to Light Blue (4000K). Options: Blue (5000K) for whitest color, Yellow (3000K) for least white.
• Photocell: Controls light based on ambient light levels.
• Motion: Controls light based on detected motion.

Tighten switch cover to a minimum of 1.5ft-lbs (2Nm) to a maximum of 1.8ft-lbs (2.5Nm).

Wiring and Fixture Operation

CAUTION: Make sure power is turned off.

• Connect fixture to supply wires rated for at least 75°C (167°F).
• To Ground fixture: Use Wire Nut to connect the (copper) house supply ground wire & the (green) fixture ground wire. Note: If house wiring does not include a ground wire, consult your local electrical code for approved grounding methods.
• To connect supply wires: Use Wire Nuts to connect the black fixture wire to the black power supply wire and the white fixture wire to the white (neutral) supply wire.
• For proper connection, place wire nut over wires and twist clockwise until tight.

Turn on electricity at fuse or circuit breaker and verify success of installation.

Troubleshooting

If this fixture fails to operate properly, use the guide below to diagnose and correct the problem.

• Verify that power is turned on at switch and breaker.
• Verify that fixture is wired properly.
• Verify that line voltage is correct.

Note: NOT suitable for use with dimmers, motion sensors or other remote devices.

If further technical assistance is required, contact Technical Support at: (800) 279-8041.

Cleaning and Maintenance

Caution: Be sure fixture temperature is cool enough to touch. Do not clean or maintain while fixture is energized.

This LED light provides low maintenance service with no bulbs to change. Clean surfaces with mild soap and water. Do not use abrasive materials such as scouring pads or powders, steel wool or abrasive paper.

WARNING: There are no user serviceable parts inside fixture.

Recycling Information

For information on how to recycle LED electronic products, please visit www.epa.gov.

Manufacturer Information

Acuity Brands Lighting, Inc. One Lithonia Way, Conyers, GA 30012

www.acuitybrands.com