OK SERIES SUBPANEL (PPK) INSTALLATION GUIDE

OK Subpanel BOM

Tools Required: T30 Torx Bit, Crescent Wrench, Driver or Screwdriver, 13 & 17 mm extended sockets.

Installation Instructions

1. Subpanel Bracket Installation

• Insert two cage nuts (Item 8) side-by-side into the top rails (Figure 1).
• Insert a flanged cage nut (Item 7) into the subpanel bracket slot (Item 2) from the back.
• Secure the bracket using two M6 screws (Item 9). See Detail A for visual aid.

Torque Specifications: 98 in-lbs per M6 screw

2. Conic Pin Assembly

• Insert the conic pin (Item 3) into a cutout on the bottom rail from the top.
• Important: The pin location on the rails align directly with the rear bracket hole location.
• Secure it from underneath using a M8 nut (Item 5). See Detail B.
• Tighten with crescent wrench and extended 17 mm socket.

3. Subpanel Slider Installation

• Insert two subpanel sliders (Item 4) into the square cutouts on the bottom of the subpanel (Item 1).
• Important: Ensure the flat side faces the door opening (Figure 2).

4. Subpanel Installation

• Rotate the subpanel 45° and slide it across the bottom rails until it makes contact with the conic pins (Item 3).
• Stand the panel upright so the conic pins insert into the sliders and the subpanel makes contact with the top brackets (Figure 2).
• *Ensure pins seat into the subpanel sliders.

5. Subpanel Attachment

• Secure the subpanel using two M8 hex screws (Item 6) through the front circular cutouts into the flanged cage nuts (Item 7). See Figure 3 for details.

Torque Specifications: 98 in-lbs per M8 hex screw.

ADDITIONAL DETAILS

Subpanel Slider & Installation Detail:

Install the two subpanel sliders into the square cutouts on the bottom of the subpanel. Rotate the subpanel and slide it along the rails until it makes contact with the conic pins. Lift and orient the subpanel vertically to engage with the top brackets (Figure 2).

Subpanel Fasteners Detail:

Insert the M8 hex screw through the circular subpanel cutout. Fasten the screw to the flanged cage nut attached to the subpanel bracket (Figure 3).

Cage Nut Detail:

Insert the cage nut (Item 8), non-flange side away from the rail corners, at a 45° angle. Slide flush with the rail (Figure 4).

• Google Docs
• Google Drive
• Download [pdf]
• Download Optimized



File Info : application/pdf, 2 Pages, 699.83KB

Document Document
ok-pna-ppk Adobe PDF Library 17.0

Related Documents

	OK Series Subpanel (APK) Installation Guide This guide provides step-by-step instructions for installing the OK Series Subpanel (APK), including subpanel bracket installation, conic pin assembly, subpanel slider installation, and subpanel attachment. It details the tools required and torque specifications for each step.
	OK Series Plinth Installation Guide This guide provides step-by-step instructions for the installation of the OK Series Plinth, including corner element assembly, side flange assembly, and front/rear plate assembly. It details the necessary tools, parts, and torque specifications for each step.
	OK Series Mounting Profile Installation Guide Installation guide for Saginaw Control & Engineering's OK Series mounting profiles, detailing the assembly of closed flange and open flange profiles.
	OK Series Plate Filler Installation Guide Installation guide for the OK Series Plate Filler (FUP) from Saginaw Control & Engineering, detailing the assembly process with a Bill of Materials and step-by-step instructions.
	OK Series Rear and Side Panel Installation Guide | Saginaw Control & Engineering Comprehensive installation guide for Saginaw Control & Engineering's OK Series rear and side panels, detailing components, tools, and step-by-step assembly procedures.
	Saginaw Control & Engineering OK Series Inner Modular Elements Guide Assembly guide for Saginaw Control & Engineering's OK Series inner modular elements, detailing the installation of screwed covers, hinged covers, adjustable mounting plates (CPR), and DIN rail supports (MTK). Includes Bill of Materials and assembly instructions.
	OK Series Eyebolt Installation Guide This guide provides step-by-step instructions for installing eyebolts on OK Series enclosures, including important safety information for lifting heavier loads.
	OK Series Top Filler Plate Installation Guide Step-by-step installation guide for the Saginaw Control & Engineering OK Series Top Filler Plate (TTP), detailing assembly procedures and required tools.