Singing Machine SML652BK/SML652P Karaoke Machine Instruction Manual

Warnings

CAUTION: RISK OF ELECTRIC SHOCK

To reduce the risk of electric shock, do not remove cover (or back). No user-serviceable parts inside. Refer servicing to qualified service personnel. The Caution marking is located on the bottom panel.

DANGEROUS VOLTAGE

The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated dangerous voltage within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.

ATTENTION

The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying this product.

DRIPPING WARNING

This product shall not be exposed to dripping or splashing, and no objects filled with liquids, such as vases, shall be placed on the product.

VENTILATION WARNING

The normal ventilation of the product shall not be impeded for intended use.

CAUTION: TO PREVENT ELECTRIC SHOCK

Match wide blade of plug to wide slot and fully insert.

WARNING: TO PREVENT FIRE OR SHOCK HAZARD

Do not expose this unit to rain or moisture.

FCC WARNING

This equipment may generate or use radio frequency energy. Changes or modifications to this equipment may cause harmful interference unless the modifications are expressly approved in the instruction manual. The user could lose the authority to operate this equipment if an unauthorized change or modification is made.

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

The rating information is located at the bottom of the unit.

INDUSTRY CANADA NOTICE

This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada's licence-exempt RSS(s). Operation is subject to the following two conditions: (1) This device may not cause interference. (2) This device must accept any interference, including interference that may cause undesired operation of the device.

Warning

Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

CAN ICES-3(B)/NMB-3(B)

Important Safety Information

1. Read these Instructions.
2. Keep these Instructions.
3. Heed all Warnings.
4. Follow all Instructions.
5. Do not use this apparatus near water.
6. Clean only with a dry cloth.
7. Do not block any of the ventilation openings. Install in accordance with the Manufacturer's instructions.
8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.
9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. When the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.
10. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.
11. Only use attachments/accessories specified by the manufacturer.
12. Use only with a cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.
13. Unplug this apparatus during lightning storms or when unused for long periods of time.
14. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.
15. WARNING: To reduce the risk of fire or electric shock, do not expose this apparatus to rain or moisture. Do not place objects filled with water, such as a vase, on the apparatus.
16. The AC mains plug is used as the power disconnect device and it should remain readily accessible and operable during intended use. In order to completely disconnect the apparatus from power, the mains plug should be completely removed from the AC outlet socket.
17. CAUTION: To reduce the risk of fire or explosion, do not expose batteries to excessive heat such as sunshine, fire or other heat sources.

Included Items

Please make sure the following items are included:

• Main Unit
• AC Adapter
• Manual
• Wired Microphone

Location of Controls (Front)

The front panel of the Singing Machine SML652BK/SML652P features various controls and indicators for operation:

• 1. Play/Pause indicator: Shows the status of playback.
• 2. Record indicator: Shows the status of recording.
• 3. Bluetooth Button: Activates Bluetooth mode.
• 4. Bluetooth indicator: Shows Bluetooth connection status.
• 5. ON/STANDBY Button: Powers the unit on or off.
• 6. MIC VOLUME Control: Adjusts the volume for microphones.
• 7. LIGHTS/FUNCTION Button: Controls speaker light modes and functions.
• 8. VOCAL/VOICE EFFECTS Button: Selects vocal effects.
• 9. RECORD Button: Initiates vocal recording.
• 10. STOP Button: Stops playback or recording.
• 11. USB Port: For connecting USB flash drives.
• 12. Speaker: The main audio output.
• 13. Handle: For carrying the unit.
• 14. Display: Shows information such as mode, track title, etc.
• 15. Favorite indicator: Indicates favorite status.
• 16. FAVOR / Navigation [Left Arrow] Button: Navigates or selects favorites.
• 17. MASTER VOLUME Control: Adjusts the overall volume of the unit.
• 18. PLAYLIST / Navigation [Right Arrow] Button: Navigates or manages playlists.
• 19. Skip [Rewind]/ Navigation [Down Arrow] Button: Skips tracks backward or navigates down.
• 20. Skip [Fast Forward]/ Navigation [Up Arrow] Button: Skips tracks forward or navigates up.
• 21. Playlist indicator: Shows playlist status.
• 22. PLAY/PAUSE [Play/Pause Symbol]/ ENTER Button: Controls playback and confirms selections.

Location of Controls (Rear)

The rear panel provides connection ports:

• 1. MIC 1 Jack: Connects the first microphone (6.3mm jack).
• 2. MIC 2 Jack: Connects the second microphone (6.3mm jack).
• 3. Extendable MIC holders: Secures microphones when not in use.
• 4. HDMI Jack: Outputs video and audio to a TV.
• 5. AUX IN Jack: Accepts audio input from external devices (3.5mm jack).
• 6. DC IN Jack: Connects the AC power adapter.

Playback Display: The display can show Song Title, Elapsed Time, Playback Status, Song Total Time, Current Playlist, Record Status, and Lead Vocal Status. Master Volume ranges from 0-20.

Connection

Connecting the Microphone(s)

Connect a microphone into MIC 1 Jack or MIC 2 Jack. Note: Avoid dropping or tapping microphones, as this can damage the mic or speakers. Do not twist the microphone cord, as this can damage the internal wiring.

Connecting the Unit to a TV

To output video, lyrics, and audio to your TV, connect an HDMI cable (not included) from the unit's HDMI Jack (Out) on the rear to the HDMI input on your TV. It is highly recommended to use a TV for the best experience. To display lyrics, play MP4 or MP3+G files via USB.

Connecting to AC Power

Insert the AC power cord into a conveniently located AC outlet (120V, 60Hz). Ensure all other connections are made before connecting to AC power.

Inserting Batteries

Slide the battery door to reveal the compartment. Insert six (6) "C" size alkaline batteries (not included) as indicated. Replace the cover tightly before operating.

Battery Precautions:

• Use only the specified battery size and type.
• Ensure correct polarity when installing batteries.
• Do not mix battery types or old/new batteries.
• Remove batteries if the device will not be used for a long period.
• Do not attempt to recharge non-rechargeable batteries.
• Rechargeable batteries must be removed before charging and charged under adult supervision.
• Exhausted batteries must be removed.
• Do not expose batteries to excessive heat.

Connecting to AUX IN Jack

Connect an external device using a 3.5mm audio cable (not included) to the AUX IN Jack on the rear of the unit. This allows audio to be played through the Singing Machine. It is recommended to set the external unit's volume to 1/3 or lower to avoid distortion. File/track skipping is not possible when using an external device.

Cradle

The unit includes a cradle for holding a smartphone or tablet.

Operation

Voice Effects

Repeatedly press the VOCAL/VOICE EFFECTS Button to select different vocal effects. The display will show the selected effect:

• EF0 - OFF
• EF1 - ECHO
• EF2 - FEMALE
• EF3 - MALE
• EF4 - CHIPMUNK
• EF5 - ROBOT
• EF6 - RADIO

Speaker Lights

When the unit is turned on, the speaker lights activate automatically and synchronize with the sound. Press and hold the LIGHTS/FUNCTION Button for Light mode 2 (light show without sound response). Press and hold the LIGHTS/FUNCTION Button again to turn off the lights.

Bluetooth Mode

Press the Bluetooth Button to enter Bluetooth mode. Press and hold the Bluetooth Button to enter pairing mode. The unit searches for and pairs with previously paired devices. If no devices are found, press and hold the Bluetooth Button again; the indicator will flash blue and red. To disconnect paired devices, press and hold the Bluetooth Button.

Using a Bluetooth Device

1. Turn on the unit using the [Power Button].
2. Press the LIGHTS/FUNCTION Button repeatedly to select Bluetooth mode ("bt" displayed).
3. On your device, enable Bluetooth and search for discoverable devices. Select "Singing Machine".
4. The Bluetooth indicator will turn solid, and a chime will sound upon successful pairing.
5. To control playback from the unit, press the [Play/Pause/Enter Button]. Press it again to pause.
6. Adjust volume using the MASTER VOLUME control on the unit and your Bluetooth device.
7. Connect microphones and turn them ON.
8. Adjust the MIC VOLUME control as needed.
9. Skip tracks using the [Skip Rewind/Down Arrow] or [Skip Fast Forward/Up Arrow] buttons.
10. RECORD YOUR VOCAL PERFORMANCE: Press the RECORD Button to start recording your voice along with the music. The record indicator will flash. Press the RECORD Button again to stop. Recorded files are saved to the USB drive with a "BT" prefix.
11. VOCALS: Press and hold the VOCAL/VOICE EFFECTS Button to sing without the lead singer. Press and hold again to resume the lead singer. (Note: This function may depend on the song recording format).
12. VOICE EFFECTS: Repeatedly press the VOCAL/VOICE EFFECTS Button to select effects like ECHO, FEMALE, MALE, CHIPMUNK, ROBOT, or RADIO. Select OFF for no effect.
13. Press the [Power Button] to turn the unit off.

Notes for Bluetooth: If prompted for a passcode, enter "0000". Some devices may require selecting "Use as Audio Device". Ensure the distance between the unit and device does not exceed 30 feet/10 meters if the connection is lost.

Playing Songs from the USB

1. Connect the unit and turn it on using the [Power Button].
2. Insert a USB flash drive with MP3 or MP4 files into the USB Port.
3. Press the LIGHTS/FUNCTION Button to select USB mode ("USb" displayed). Press the [Play/Pause/Enter Button] to start playback. Press again to pause, or the STOP Button to stop. If connected to a TV, karaoke videos will play on screen.
4. It is recommended to connect to a TV for USB playback. Use the [Skip Rewind/Down Arrow] and [Skip Fast Forward/Up Arrow] buttons to navigate through songs.
5. Adjust volume using the MASTER VOLUME control. If connected to a TV, adjust the TV's volume.
6. Connect microphones and turn them ON.
7. Adjust the MIC VOLUME control as desired.
8. Skip tracks using the [Skip Rewind/Down Arrow] or [Skip Fast Forward/Up Arrow] buttons. You can also press and hold these buttons to skip ahead 10 files/tracks.
9. Press the STOP Button to stop playback.
10. RECORD YOUR VOCAL PERFORMANCE: Press the RECORD Button to record your singing with the music. The record indicator will flash. Press RECORD again to stop. Recorded files are saved to the USB drive.
11. VOCALS: Press and hold the VOCAL/VOICE EFFECTS Button to sing without the lead singer. Press and hold again to resume the lead singer. (Note: This function may depend on the song recording format).
12. VOICE EFFECTS: Repeatedly press the VOCAL/VOICE EFFECTS Button to select effects like ECHO, FEMALE, MALE, CHIPMUNK, ROBOT, or RADIO. Select OFF for no effect.
13. SEARCHING BY GENRE, ARTIST or TITLE (TV only): In USB menu, press the STOP Button to enter search mode ("SEA" displayed). Use [Favor/Navigation Left] or [Playlist/Navigation Right] buttons to select search criteria, then press [Play/Pause/Enter Button]. Use navigation buttons to select letters and songs.
14. CREATING THE PLAYLIST: Select a song using navigation buttons and press [Playlist/Navigation Right] to add it. "Added" will appear. Repeat to add more songs. You can also press [Playlist/Navigation Right] during playback. Playlists are saved even if the unit is reset.
15. USING THE PLAYLIST: In USB menu, press the STOP Button to enter search mode. Select "Playlist" and press [Play/Pause/Enter Button]. Use navigation buttons to select and play songs from your playlist. Select "PLAY ALL" to play the entire playlist.
16. PRIORITY: Select PRIORITY, then use navigation buttons to prioritize songs. Press [Favor/Navigation Left] and [Playlist/Navigation Right] to assign numbers (0001, 0002, etc.). Press [Play/Pause/Enter Button] to confirm. Use navigation buttons to select songs for PLAYALL.
17. REMOVE: Select REMOVE, then select a song using navigation buttons and press [Play/Pause/Enter Button] to delete it from the playlist.
18. RM ALL: Select RM ALL and press [Play/Pause/Enter Button] to empty the entire playlist.
19. CREATING FAVORITES: Select a song using navigation buttons and press [Favor/Navigation Left] to add it to favorites. The icon turns orange. Repeat for more songs. Favorites are stored even if the unit is reset.
20. USING THE FAVORITES: In USB menu, press the STOP Button to enter search mode. Select the FAVORITE tag using [Favor/Navigation Left] or [Playlist/Navigation Right] buttons. Press [Play/Pause/Enter Button] to view the favorites list and play/edit as with playlists.
21. Press the [Power Button] to turn the unit off.

Notes for USB Playback: A loading icon will appear while files are loading. The USB mode cannot be accessed until a flash drive is inserted.

Playing Songs from the Recorded Files

1. Connect the unit to a TV and turn it on.
2. Press the LIGHTS/FUNCTION Button to select Recordings mode ("rEC" displayed).
3. Use navigation buttons ([Skip Rewind/Down Arrow] and [Skip Fast Forward/Up Arrow]) to browse recorded files on your USB drive.
4. Press the [Play/Pause/Enter Button] to start playback or pause.
5. Adjust volume using the MASTER VOLUME control. If connected to a TV, adjust the TV's volume.
6. Connect microphones and turn them ON.
7. Adjust the MIC VOLUME control as desired.
8. Skip tracks using the [Skip Rewind/Down Arrow] or [Skip Fast Forward/Up Arrow] buttons. You can also press and hold these buttons to skip ahead 10 files/tracks.

Notes for Recorded Files: Recording mode requires a flash drive. Recorded audio files are saved to the USB drive with a "LINEIN" prefix (for AUX IN recordings) or "BT" prefix (for Bluetooth recordings).

Using the AUX IN Jack

1. Connect the unit and turn it on using the [Power Button].
2. Connect an external unit to the AUX IN Jack on the rear. This allows audio to play through the Singing Machine. Set the external unit's volume to 1/3 or lower to avoid distortion.
3. Press the LIGHTS/FUNCTION Button to select AUX IN mode ("AU" displayed).
4. Adjust volume using the MASTER VOLUME control on this unit or the external device.
5. Connect microphones and turn them ON.
6. Adjust the MIC VOLUME control as desired.
7. VOICE EFFECTS: Repeatedly press the VOCAL/VOICE EFFECTS Button to select effects like ECHO, FEMALE, MALE, CHIPMUNK, ROBOT, or RADIO. Select OFF for no effect.
8. RECORD YOUR VOCAL PERFORMANCE: Press the RECORD Button to record your singing with the music. The record indicator will flash. Press RECORD again to stop. Recorded files are saved to the USB drive with a "LINEIN" prefix.
9. Press the [Power Button] to turn the unit off.

Where to Download Files

Where to Download MP4 Files

Visit www.singingmachine.com/pages/app-install and follow the instructions to install the Karaoke Store App.

Where to Download MP3+G Files

To purchase and download karaoke music, visit store.singingmachine.com. You will need a USB flash drive (not included) to transfer downloads.

Helpful Hints for MP3+G Files:

• MP3 and CDG files are delivered in a compressed MP3+G.zip file.
• The MP3+G file cannot be played directly from a .zip file on a USB drive.
• To play karaoke songs from a USB drive:
  • Connect a USB flash drive to your computer.
  • Download the MP3+G file from your Digital Locker and save the .zip file to a folder on your computer.
  • Double-click the .zip file to open it and access the .mp3 and .cdg files.
  • Drag and drop the .mp3 and .cdg files to the USB flash drive.
  • Eject the USB flash drive from your computer.
  • Turn on the Singing Machine and connect the USB flash drive.

FAQ

For additional help with file formats, visit www.singingmachine.com/smc-music/ for resources on supported file formats.

Troubleshooting Guide

No Power

• Ensure the [Power Button] is pressed.
• Confirm the AC adapter is securely connected to the unit.
• Try connecting to a different outlet.
• Strong Electro-Magnetic Interference may affect normal function. Restart the product or try using it in a different location.

No Sound – General

• Check if Master Volume is set to minimum; raise it.
• Ensure the correct function is selected using the LIGHTS/FUNCTION Button.
• If using an external device, ensure its volume is raised.

No Sound – If connected to a TV

• Check if the TV volume is muted or too low.
• Ensure the correct source (usually HDMI) is selected on the TV's menu.

No sound from the microphone

• Make sure the microphone is firmly connected to the MIC 1 or MIC 2 jack.
• Ensure the ON/OFF switch on the microphone is in the ON position.
• Check that the MIC VOLUME control is not set too low.
• Ensure MASTER VOLUME is not set to minimum.

The Bluetooth device cannot be paired or connected with the unit

• Ensure your device's Bluetooth function is activated.
• Make sure the system is in pairing mode (press and hold the Bluetooth Button).
• Turn off any other Bluetooth devices that might interfere.

The Music is not available on the unit after successfully connecting the Bluetooth

• Ensure your Bluetooth device supports the A2DP Bluetooth profile.
• Check that the volume on the external Bluetooth device is not too low or muted.
• Make sure your music application is open.

Energy Saving (Auto Power System-APS)

This unit will automatically turn off after 20 minutes of inactivity to save energy. Press the [Power Button] to turn it back on.

Specifications

Audio

• OUTPUT POWER (MAXIMUM): 5 Watts (RMS)
• OUTPUT IMPEDANCE: 4 Ohms

USB

• Format: FAT32
• Maximum Capacity: 32GB

Bluetooth

• Bluetooth Version: V5.0
• Working Distance: Up to 30 feet/10 meters measured in open space

AUX IN SECTION

• Microphone Input: 3.5 mm Stereo Headphone Jack
• Microphone Impedance: -74db 600 Ohm Impedance with 6.3 mm Dynamic Microphone

Power Section

• Input: DC 9V ⎓ 1A, DC 9V (6 x "C" batteries) (Batteries not included)

Dimensions (HxWxD)

• 11.2 x 8.3 x 5.4 inches / 28.4 x 21 x 13.8 cm

Weight

• 3.19 lbs/1.45 kgs

Specifications are subject to change without notice.

Trademarks: HDMI and HDMI High-Definition Multimedia Interface, and the HDMI Logo are trademarks of HDMI Licensing Administrator, Inc. Bluetooth® word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. Other trademarks and trade names are those of their respective owners.