Delta DOP-107EG HMI Instruction Sheet
This document provides information about the DOP-100 series HMI. Please read carefully before use.
General Precautions
- Install in an indoor location free of vapor, corrosive, and inflammable gas and liquids.
- Refer to wiring diagrams for connections.
- Ensure proper grounding according to national electrical standards (e.g., NFPA 70).
- Do not disassemble or change wiring while power is on.
- Avoid touching the power supply when power is on to prevent electric shock.
- Contact a local distributor or Delta Customer Service Center for battery replacement if a low power notification appears; do not replace batteries yourself.
- This product is intended for use with other industrial automation equipment. Follow instructions carefully to avoid danger.
- Clean with a dry cloth.
- Use at altitudes below 2,000 m.
- Failure to use as specified may impair product protection.
- For repair and maintenance, contact Delta Electronics, Inc.
- For inquiries, contact local distributors or Delta sales representatives. The content may be revised without notice. Download the latest version from Delta's website: www.delta.com.tw/ia.
Description of Each Part
Front View (DOP-107EG): Features the operation/display area and the Delta logo.
Rear View (DOP-107EG): Includes ports labeled A through G: A - USB Host, B - USB Slave, C - Network Port (LAN), D - Audio Output Interface, E - Power Input Terminal, F - COM2/COM3, G - COM1.
Communication Port Pin Assignment
DOP-107EG COM1 Port
| COM Port | Pin | MODE1 (RS-232) |
|---|---|---|
| COM 1 | 1 | - |
| 2 | RXD | |
| 3 | TXD | |
| 4 | - | |
| 5 | GND | |
| 6 | - | |
| 7 | RTS | |
| 8 | CTS | |
| 9 | - |
DOP-107EG COM2 Port
| COM Port | Pin | MODE1 (RS-232) | MODE2 (RS-485) | MODE3 (RS-422) |
|---|---|---|---|---|
| COM 2 | 1 | - | D+ | TXD+ |
| 2 | RXD | - | RXD | |
| 3 | TXD | - | TXD | |
| 4 | - | D+ | RXD+ | |
| 5 | GND | GND | GND | |
| 6 | - | D- | TXD- | |
| 7 | RTS | - | RTS | |
| 8 | CTS | - | CTS | |
| 9 | - | D- | RXD- |
Note: A dash (-) indicates the connection is not required.
Mounting Dimensions
The unit dimensions are 184 mm (Width) x 144 mm (Height) x 51.5 mm (Depth). The panel cutout dimensions are 172.4 mm (Width) x 132.4 mm (Height).
A minimum clearance of 60 mm is required on the rear of the HMI for heat dissipation.
Installation and Wiring
Precautions
- Incorrect installation may cause malfunction.
- Ensure sufficient space around the HMI for ventilation.
- Use on a case/platform conforming to enclosure Type 4X standard (indoor use only).
- Maximum panel thickness for mounting is 5 mm.
- Use copper conductors only.
Installation Steps
- Insert the waterproof gasket into the HMI and then insert the HMI into the panel cutout.
- Place fasteners into the slots and tighten the screws until they reach the panel cutouts.
- Tighten screws with a torque less than 0.5 N-M / 0.7 N-M (DOP-107EG torque: 6.17 lb-inch or 0.7 N-M) to avoid damaging the plastic case.
- Ensure a minimum clearance of 60 mm on the rear of the HMI for heat dissipation.
Wiring
Wiring Details:
- Type: Solid, Stranded
- Wire Gauge (AWG): 24-12
- Stripped Length: 7-8 mm
- Torque: 5 kg-cm (4.3 lb-in)
Power Connector Wiring: Use cables with a temperature rating greater than 75°C (167°F).
Hardware Specifications
| Specification | Details |
|---|---|
| Model | DOP-107EG |
| Panel Type | 7" TFT LCD (65535 colors) |
| Resolution | 800 x 600 pixels |
| Backlight | LED backlight (half-life under room temperature 25°C > 20,000 hours) |
| Display Range | 141.00 x 105.75 mm |
| Brightness | 450 cd/m² (Typ.) |
| CPU | ARM Cortex-A8 (800 MHz) |
| Flash ROM | 256 Mbytes |
| RAM | 256 Mbytes |
| Touchscreen | 4-wire resistive touchscreen > 10,000,000 operated |
| Buzzer | Multi-tone frequency (2 K - 4 KHz) / 80 dB |
| Sound Effect Output | Stereo output |
| Network Interface | 10/100 Mbps Auto sensing (with built-in isolated power circuit) |
| USB | 1 USB slave Ver 2.0; 1 USB host Ver 2.0 |
| SD | SD * 1 |
| Serial Communication Port COM1 | RS-232 (supporting flow control) |
| Serial Communication Port COM2 | RS-232 (supporting flow control) / RS-485 |
| Serial Communication Port COM3 | RS-422 / RS-485 |
| Auxiliary Function Key | N/A |
| Calendar | Built-in |
| Cooling Method | Natural cooling |
| Approvals | CE / UL (Use shielding network cable and magnetic ring with a 300 ohm / 100 MHz filter) |
| Panel Waterproof Level | IP65 / NEMA4 / UL TYPE 4X (indoor use only) |
| Operation Voltage*2 | DC +24 V (-15% to +15%) (Use an isolated power supply; supplied by Class 2 or SELV circuit, isolated from MAINS by double insulation) |
| Leakage Current | 500 VAC for 1 minute (between DC24V terminal and FG terminal) |
| Power Consumption*2 | 8.4 W (Max) |
| Backup Battery | 3V lithium battery CR2032 × 1 |
| Backup Battery Life | About 3 years or more at 25°C (subject to operation temperature and condition) |
| Operation Temperature | 0°C to 50°C (32°F to 122°F) |
| Storage Temperature | -20°C to +60°C (-4°F to 140°F) |
| Operating Environment | 10% to 90% RH [0°C to 40°C], 10% to 55% RH [41°C to 50°C]; pollution degree: 2 |
| Vibration Resistance | Conforms to IEC61131-2: continuous vibration 5 Hz - 8.3 Hz with amplitude 3.5 mm; 8.3 Hz - 150 Hz with amplitude 1G |
| Shock Resistance | Conforms to IEC60068-2-27: 11 ms, 15 G Peak, in X, Y, Z directions each for 6 times |
| Dimension (W) x (H) x (D) mm | 184 x 144 x 51.5 |
| Mounting Dimension (W) x (H) mm | 172.4 x 132.4 |
| Weight | Approx. 800 g |
Notes
- The half-life of the backlight is defined as the maximum luminance being reduced by 50% when the maximum drive current is supplied to the HMI. The life of LED backlight shown here is estimated at room temperature of 25°C with ambient humidity.
- The withstand voltage of the isolated power circuit is 1500 V peak for 1 minute.
- The HMI power consumption is the power consumed when the HMI is not connecting with other peripheral devices. For normal operation, the recommended power supply capacity is 1.5 to 2 times the specified power consumption.
- An isolated power supply is recommended.
- DOP-100 series programming software (DOPSoft) and user manuals can be downloaded from www.delta.com.tw/ia.
- DOP-100 series can be used with other industrial automation equipment. Read this sheet carefully and install according to instructions to avoid danger.
Hazardous Substances Information
| Part Name | Lead (Pb) | Mercury (Hg) | Cadmium (Cd) | Hexavalent Chromium (Cr VI) | Polybrominated Biphenyls (PBB) | Polybrominated Diphenyl Ethers (PBDE) |
|---|---|---|---|---|---|---|
| Metal Part | X | O | O | O | O | O |
| Plastic Part | O | O | O | O | O | O |
| Electronic Component | X | O | O | O | O | O |
| Contacts | O | O | O | O | O | O |
| Cable & Cabling accessories | X | O | O | O | O | O |
| Battery | O | O | O | O | O | O |
This table is compiled according to SJ/T 11364. O: Concentration of hazardous substance is below the limit stipulated in GB/T 26572. X: Concentration of hazardous substance exceeds the limit stipulated in GB/T 26572.
