Roomba Plus 505 Combo Robot + AutoWash Dock Owner's Guide
Getting Started
- Remove foam inserts behind the bumper.
- Install the Edge-Sweeping brush and mop pads. Align the Edge-sweeping brush and press down until it clicks.
- Install the dock ramp by aligning it with the dock and pressing down to snap into place.
- Place the dock on a hard surface flooring, ensuring good Wi-Fi coverage. Keep it at least 1.5 ft (0.5 m) from both sides, 4 ft (1.2 m) from stairs, and 4 ft (1.2 m) in front. Avoid direct sunlight and clutter around the dock for optimal docking performance.
Setup and Operation
- Prepare the clean water tank: Remove it from the dock, fill with water and compatible cleaning solution (check http://answers.irobot.com/s/roomba-combo-cleanser for compatible solutions). Do not use other solutions or bleach-based products.
- Plug in the dock: Connect the power cord and wrap excess cord to prevent interference with the robot.
- Wake up the robot: Place the robot in front of the dock, slide it towards the dock, aligning the charging contacts. A sound will indicate it's awake. Charge for up to 4 hours before the first cleaning. To remove the robot, slide it towards you and lift.
- Download the Roomba® Home App: Scan the QR code or search for the app in your app store to guide you through setup and access features like custom cleaning schedules, preferences, and tips.
About Your Roomba® Plus 505 Robot
Top View
- 1 Charging Contacts
- 2 Dock Alignment Guides
- 3 Debris Evacuation Port
- 4 LIDAR Detector Bumper
- 5 ClearView™ LIDAR
- 6 Home Button
- 7 Power Button
- 8 Robot Top Cover
Bottom View
- 9 Filter
- 10 AutoEmpty™ Port or Debris Evacuation Port
- 11 Bin Release Button
- 12 Bin
- 13 Bumper
- 14 Wall Follow Sensor
- 15 Wheel
- 16 Multi-Surface Brush
- 17 Cliff Sensors
- 18 Floor Type Sensor
- 19 Caster Wheel
- 20 Camera and Illumination LED
- 21 Mop Pad
- 22 Mop Pad Plate
- 23 Mop Pad Extendor
- 24 Brush Cover
- 25 Brush Cover Release Tab
- 26 Edge-Sweeping Brush
About Your AutoWash™ Dock
Front View
- 1 Dirty Water Tank
- 2 Clean Water Tank
- 3 Charging Contacts
- 4 Dock Alignment Guides
- 5 AutoWash™ Water Inlet
- 6 AutoWash™ Pad Dry recess
- 7 AutoWash™ Water drain
- 8 Trash Indicator
- 9 Dirty Water Tank LED Indicator
- 10 Clean Water Tank LED Indicator
- 11 Charging LED Indicator
- 12 IR Window
- 13 Debris Bag Storage
- 14 Extra Debris Bag
- 15 Debris Bag Guide Rails
Rear View
- 16 Cleaning Brush Accessory
- 17 Debris Evacuation Port
- 18 Main Debris Cubby
- 19 Dock Filter
- 20 Cubby Door
Top View
- 21 Water Tank Handle
- 22 Water Tank Lid
- 23 Water Tank Latch
- 24 Exhaust Vent
- 25 Removable Power Cord
- 26 Cord Attachment
- 27 Cord Wrap
- 28 Water Entry Point
- 29 Dirty Water Float
- 30 Clean Water Tubing
- 31 Clean Water Float
- 32 Removable Ramp
- 33 Wheel Track
Charging
Power Icon Indicator:
- White: Fully charged and connected.
- Flashing White: Return to dock to charge.
- Pulsing White: Charging (low battery).
- Flashing Red: Low battery/Error.
Dock Charging LED Indicators:
- Solid White: Robot is fully charged or charging. Also indicates when the dock is automatically emptying the bin, washing or drying pads, or in standby mode.
- Off: Robot is not on the dock, not charging, or the dock is asleep.
Charging during a cleaning routine: The robot will return to the dock to recharge and resume cleaning where it left off.
Standby mode: Press and hold the power button for 10 seconds for reduced power state. Short press to exit. Store in a cool, dry place.
Storing your robot: Turn off by removing from dock and holding power button for 10 seconds. Store in a cool, dry place.
Cleaning
Button Controls:
- POWER Button: Tap to Start/Pause/Resume. Hold for 3 seconds to turn on, 10 seconds to turn off.
- HOME button: Tap to send robot home. Press when running to pause. Press when paused to dock. Press when docking to stop.
Cleaning Pattern: The robot cleans in neat rows and returns to the dock when finished or needing to recharge. It automatically empties its dust bin at the end of each cleaning routine.
Spot Clean: Tap the power button twice to spot clean a designated area. The robot will end the job upon completion.
Tips: Remove excess clutter before cleaning. Use the robot frequently. After 90 minutes of inactivity off the dock, the robot ends its cleaning. Check the Roomba® Home App for status.
Note: Do not use mopping functions on unsealed hardwood floors or certain laminate/vinyl planks due to potential water damage. Visit global.irobot.com for more information.
Recommended: Use the Roomba® Home App for cleaning control, specific room cleaning, and scheduling.
Starting a Cleaning Routine from Your Dock
If clean and dirty water tanks require maintenance (indicated by LEDs), follow these steps:
- Lift to remove the tank needing attention.
- Lift the latch on the tank to open.
- Empty the Dirty Tank. Fill the Clean Tank with water.
- Close and latch the water tank lids. Place tanks back on the dock.
- With mop pads attached, return the robot to the AutoWash™ dock and use the app or press the HOME button on your robot.
Pad Washing and Pad Drying: The robot returns to the dock for pad washing as needed during cleaning and upon completion. Pad drying occurs at the end of the routine. Do not interrupt pad washing. It's normal to hear noises during this process. The dock blows hot air to dry the pads. Drying can last a few hours; drying times can be customized in the app. Visit the app to manually start pad washing, start/stop pad drying, or customize settings.
Care and Maintenance for Your Robot
Perform basic care and maintenance for optimal performance. Additional videos are available in the Roomba® Home App.
| Part | Care Frequency | Replacement Frequency* |
|---|---|---|
| Dust bin | Clean as needed | - |
| Filter | Clean once a week (twice if pet) | Every 3-6 months |
| Edge-Sweeping Brush | Clean every 2 weeks or as needed | Every 3-6 months |
| Multi-Surface Brush | Clean once a week | Every 6-12 months |
| Front Caster Wheel | Clean every 2 weeks or as needed | - |
| Charging Contacts | Clean every 2 weeks or as needed | - |
| Sensors | Clean once a month or as needed | - |
| Mop Pad | Auto cleans after mopping | Every 180 hours of cleaning |
| Brush Cover | Inspect every 6 months | Replace if worn or damaged |
Cleaning the Edge-Sweeping Brush: Pull to remove, clear hair/debris with the cleaning brush, then reinstall.
Cleaning the Multi-Surface Brush: Press brush cover release tabs, lift to remove cover. Remove the multi-surface brush. Clear hair/debris with the cleaning brush. Reinstall the brush and cover.
Cleaning the Filter and Bin: Remove top cover, press bin release buttons to remove bin. Remove filter. Clean debris from filter with cleaning brush. Open bin door, empty and clean bin and filter. Close bin door. Reinsert filter. Place bin back in robot. Return top cover. Note: If placing robot on dock by hand, it won't empty automatically; use the app or hold the button for 2-5 seconds.
Washing the Bin: Release bin, remove filter, open bin door. Rinse dust bin with warm water. Ensure bin is completely dry. Reinsert filter and place bin back in robot. Note: Bin is not dishwasher safe.
Care and Maintenance for Your Dock
Perform procedures for optimal dock performance.
| Part | Care Frequency | Replacement Frequency* |
|---|---|---|
| Charging contacts | Clean once a month | - |
| Sensors | Clean once a month | - |
| IR window | Clean once a month | - |
| Bags | Replace when full (indicated by LED/App) | - |
| Clean tank | Rinse and refresh water as needed | - |
| Dirty tank | Rinse and empty as needed | - |
| Pad washing basin, Liquid overflow basin | Clean if visibly dirty, once a month | - |
| Ramp | Clean if visibly dirty | - |
Cleaning the Front Caster Wheel: Use the cleaning brush to remove hair and debris. If the wheel isn't spinning freely after cleaning, contact Customer Care.
Cleaning the Charging Contacts, Sensors, and Camera Window: Remove robot from dock. Wipe charging contacts and sensors with a clean, dry cloth or lightly dampened melamine foam. Do not spray cleaning solution or water onto sensors or openings.
Removing Debris from Dock Filter: Inspect dock filter for lint/debris, wipe with a clean dry cloth.
Cleaning the Pad Washing System: Wipe the Pad Washing Basin with a clean dry cloth. Ensure the drainage port is clear. Mild soap and a sponge can be used for stubborn debris. Do not spray cleaning solution or water onto sensors or sensor openings.
Replacing the Bag: Pull cubby door towards you and up to remove. Slide card out; the bag self-seals. Install a new bag by sliding the card into guide rails. Replace cubby door, ensuring correct alignment.
Washing the Water Tanks: Remove both tanks. Lift latch to open. Empty Dirty Water tank. Rinse both tanks with warm water (mild soap and sponge for stubborn debris). Refill clean water tank. Leave dirty water tank empty. Reinsert tanks. Water tanks are not dishwasher safe.
Troubleshooting
Troubleshooting your robot: The robot alerts with voice announcements or audio alerts. The Roomba® Home App provides notifications with troubleshooting steps.
Troubleshooting your dock: The dock indicates errors via LED indicators and the Roomba® Home App. Check the app for errors.
LED indicator (Bag): Solid red means the bag is full or missing. Replace or securely insert the bag. If the problem persists, remove debris from the port on the bottom of your robot and dock.
Thermal Protector: If the motor stops due to overheating, unplug the unit, allow it to cool for 30 minutes, clear obstructions from the evacuation port and tube, then plug it back in.
Factory Reset: Press and hold the power button for 5 seconds, then within 5 seconds, press and hold the HOME button for 5 seconds.
Need Further Assistance?
Download the Roomba® Home App or visit global.irobot.com for product support or to contact your local support center. For assistance in the US & Canada, call the US Customer Care team at (877) 855-8593. iRobot USA Customer Care Hours: Monday to Friday, 9AM - 9PM Eastern Time; Saturday and Sunday 9AM - 6PM Eastern Time.
Safety Information: Please see the safety guide that came with your robot, or visit global.irobot.com.
Battery Safety & Shipping: Lithium ion batteries are subject to stringent transportation regulations. To ship the product, the battery MUST be turned off. Turn off the battery by removing the robot from the dock and holding down the power button for 10 seconds. Press the bumper in for 10 seconds while holding the power button; all indicators will turn off. Package the robot securely for shipping.
