Kenton D-SYNC

Description

The D-SYNC features a MIDI Input and a MIDI Output for connecting to MIDI devices, with an opto-coupled MIDI Input for optimal performance. It also includes a DIN Sync Input and a DIN Sync Output for connecting to sequencers and drum machines.

The D-SYNC is powered by an included multi-region mains adaptor, offering a "fit and forget" solution without the need for periodic battery changes. Alternatively, it can be powered from a USB port on a computer or USB Hub.

Connecting

Connect the supplied USB lead's large plug end to the 5V power adaptor and the other end to the D-SYNC. Ensure the power adaptor is plugged into the mains and the ACTIVE LED on the D-SYNC is illuminated (steady green).

To convert MIDI to DIN Sync:

Connect the MIDI output of your keyboard(s) and/or computer to the D-SYNC's MIDI Input. Then, connect the D-SYNC's SYNC Out port to the DIN-SYNC input of the device you wish to control.

To convert DIN Sync to MIDI:

Connect the DIN SYNC output of your keyboard and/or computer to the D-SYNC's SYNC Input. Then, connect the D-SYNC's MIDI Out port to the MIDI input of the device you wish to control.

Conversion can occur in both directions simultaneously. Note that the D-SYNC treats a MIDI Continue message as a Start command. The USB connector is used exclusively for power; the D-SYNC is not a USB MIDI device.

Status LED

The LED displays a steady green light when power is applied and flickers to indicate when MIDI messages are being received.

Firmware Version Request

A firmware version request must be sent within 10 seconds of applying power to the unit; otherwise, it will be ignored. The firmware version request message is: F0 00 20 13 16 60 F7 (hex). The unit responds with the version number in the format: F0 00 20 13 16 6F xx xx xx xx F7 (hex), where 'xx' represents ASCII characters forming the version number. For example, F0 00 20 13 16 6F 31 32 33 34 F7 (hex) corresponds to version number 1234.

Specifications

• Power Input: USB Mini-B socket (for power only)
• Power: 5V DC regulated @ 50mA
• MIDI ports: 1 x In, 1 x Out (5 pin DIN sockets)
• SYNC ports: 1 x In, 1 x Out (5 pin DIN sockets)
• Weight: 150g (excluding power supply)
• Dimensions: 110 x 55 x 35 mm
• Power supply: Multi-region switch mode power supply supplied with unit.

Warranty

The D-SYNC is covered by a 12-month back-to-base warranty from the date of purchase. Customers are responsible for arranging and covering the cost of carriage to and from Kenton Electronics Ltd.

FCC Statement

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

Information on Disposal for Users of WEEE

The symbol [WEEE symbol] on the product and/or accompanying documents indicates that used electrical and electronic equipment (WEEE) should not be mixed with general household waste. For proper treatment, recovery, and recycling, please take this product(s) to designated collection points where it will be accepted free of charge.

Alternatively, in some countries, you may return your products to your local retailer upon purchase of an equivalent new product. Disposing of this product correctly helps save valuable resources and prevents potential negative effects on human health and the environment that could arise from inappropriate waste handling.

Please contact your local authority for details of your nearest designated collection point. Penalties may apply for incorrect disposal according to national legislation.

For disposal in countries outside the European Union: This symbol is only valid in the European Union (EU). If you wish to discard this product, please contact your local authorities or dealer for the correct disposal method.