MiBoxer B9 SPI-Panel Remote Control
Model No.: B9
Product Features
- Adjust the color and length (number of pixels) of the SPI strip, select the dynamic mode and speed, and save 8 scenes.
- 2.4GHz wireless technology with high transmission speed, stable signal, and high anti-interference capability.
- Control multiple devices simultaneously and support communication with multiple devices.
- Change the dynamic mode, color, brightness, and dynamic lighting function.
- Edit width and color for the dynamic mode.
- Set time and color for ON/OFF.
- Works with multiple controllers (control distance 30m).
- Magnetic holder with easy installation.
- Versatile for commercial or private lighting, creating atmospheric lighting.
Product Parameters
| Parameter | Value |
|---|---|
| Product Name | SPI-Panel Remote Control |
| Model No. | B9 |
| Working Voltage | 3V (2*AAA PCS) / DC3.3V |
| Standby Current | 30 μA |
| Transmit Power | 6dBm |
| Protocol | 2.4GHz RF |
| Modulation | GFSK |
| Control Distance | 30M |
| Working Temperature | -10~40℃ |
| EMC Standard | ETSI EN 301 489-1 V2.2.3 ETSI EN 301 489-3 V2.3.2 |
| Safety Standard | EN 61347-2-11:2001+A1:2019 EN 61347-1:2015+A1:2021 EN 62493:2015+A1:2022 |
| Radio Equipment | ETSI EN 300 400 V2.2.1 |
| Certification | CE, EMC, LVD, RED |
Display
The remote control display shows the following modes and functions:
- Static Mode
- Dynamic Mode
- ON / OFF status indicators
- Color adjustment
- Width adjustment
- Speed adjustment
- Dimming control
- Lock status
- Music Mode indicator
- Scene selection
Button Explanation
The remote features several buttons and sliders for control:
- Static Mode Button: Switch to pure static lighting.
- Dynamic Mode Button: Short press to cycle through dynamic modes.
- Music Mode Button: Short press to switch to Music Mode. (In Music Mode, press again to perform other operations).
- Scene Button: Works only in dynamic and music modes. Short press to recall scenes. Long press to save the current scene while the light is in dynamic mode.
- Lock Button: The remote automatically locks if no operation is performed for 15 seconds. Short press once to unlock. Press and hold for 3 seconds to turn off the remote.
Slider controls:
- RGB Slider: Touch to adjust RGB color.
- Pixel Point Slider: Slide to adjust length and width. (Refer to further instructions for details).
- Speed Slider: Touch to adjust the speed.
- Brightness Slider: Touch to adjust brightness. In Music Mode, the sensitivity of the microphone chip can be adjusted.
Pairing / Unpairing
Pairing: The controller must be paired with the remote control before use.
- Turn off the light for 10 seconds and then turn it back on.
- Short press the "ON" button 3 times within 3 seconds.
- The connection is established when the light blinks slowly three times.
Pairing failed if the light does not blink. Please repeat the above steps. (Note: Re-pairing is not possible if the remote connection is already established.)
Unpairing:
- Turn off the light for 10 seconds and then turn it back on.
- Short press "ON" 5 times within 3 seconds.
- The connection is established when the light blinks rapidly 10 times.
Unpairing failed if the light does not blink. Please repeat the above steps. (Note: Unpairing is not necessary if the light was never paired.)
Adjust Length (Pixel Count: min 8pt, max 2048pt)
Press and hold "ON" for 5 seconds until the white color lights up and the last point blinks.
Slide to change length.
Short press to add a point, long press to continuously add points.
Short press to decrease a point, long press to continuously decrease points.
Short press "ON/OFF" to exit settings.
Adjust Width for Dynamic Mode
Slide the pixel count to change the number of points and achieve different lengths for the dynamic mode with various sections.
Set Time and Color for ON/OFF
Press and hold "OFF" for 5 seconds to enter the ON/OFF mode.
Slide "Speed" to set the ON/OFF time.
Slide "RGB" to set the ON/OFF color.
Short press "ON/OFF" to exit settings.
Installation
Power Supply Options:
- Input 1: 3V (2*AAA Battery)
- Input 2: AC90~120V or AC180~240V
DC 3.3V is also indicated.
The power adapter specified for MiBoxer must be purchased separately.
Diagrams illustrate the mounting process, showing how the controller is installed into a wall or enclosure.
Attention
- Only compatible with the MiBoxer SPI-LED Controller.
- Do not use in humid or hot environments. If not in use, remove the battery and store it in a dry place or in an environment with static electricity.
- Do not use near metal or strong magnetic areas, as this will affect the signal and lead to loss of range.
Certifications: CE, UK CA, ROHS. Made in China.
