DecoFlex WireFree™ 3-Button Instructions

Product Overview

The DecoFlex WireFree™ 3-Button keypad provides a simple and elegant way to control Somfy-powered RTS interior shades. This keypad is compatible with all Somfy RTS motors and brings an intuitive single channel control experience to the DecoFlex WireFree product line.

Control Operation

LED Indicator

OPEN: Press to open drapery/raise shades.

STOP: When the drapery/shades are moving, press to stop them at the desired level. When the drapery/shades are stationary, press to send to pre-programmed intermediate "my" position.

CLOSE: Press to close drapery/lower shades.

Programming Button: Used for programming functions.

Diagram Description: A visual representation shows a three-button keypad labeled OPEN, STOP, and CLOSE. An LED indicator is positioned above the buttons. A separate button labeled "Programming Button" is also depicted.

What's In the Box

• DecoFlex WireFree™ 3-Button keypad
• Instructions
• CR2450 battery
• Mounting bracket
• Decora Switch Plate
• Mounting screws (x2)

Important Notes

• Codes: Install in accordance with all local and National Electrical Codes.
• Environment: Ambient operating temperature is 41° F to 104° F (5° C to 40° C).
• Mounting: Mounting bracket (included) allows for direct mounting to drywall. No junction box required.
• Battery: DO NOT use rechargeable batteries. Using improper batteries could damage the DecoFlex keypad.

Dimensions

Diagram Description: The dimensions section shows three views of the keypad and switch plate. The front view shows a keypad with OPEN, STOP, and CLOSE buttons, measuring 3.80 inches (97mm) in height and 3.28 inches (83mm) in width. A side view shows a depth of 0.59 inches (15mm). An exploded view shows the keypad, mounting bracket, and Decora switch plate. The Decora switch plate itself is shown, measuring 4.51 inches (115mm) in height and 2.77 inches (70mm) in width.

Installation

The keypad can be wall-mounted with the following steps:

1. Cut an opening into drywall using the mounting bracket as a guide.
2. Install the bracket securely in place.
3. Secure the keypad to the bracket using the screws provided (do not over-tighten).
4. Attach the Decora Switch Plate onto the keypad.

Initial Programming

For detailed steps on programming, please refer to the pocket programming guide at www.somfypro.com/pocket-programming-guide.

STEP 1: INITIATE PROGRAMMING

On the keypad, PRESS & HOLD both the [OPEN] and [CLOSE] buttons simultaneously until the window covering jogs. This may take up to 10 seconds.

STEP 2: CHECK THE DIRECTION OF OPERATION

On the keypad, PRESS & HOLD the [CLOSE] button and check if the window covering is closing. If the window covering does not correspond with the expected direction, PRESS & HOLD the [STOP] button until the window covering jogs to reverse the direction. Confirm before proceeding.

Diagram Description: Shows button presses for checking operation direction. Pressing [CLOSE] to check closing. If incorrect, pressing [STOP] to reverse direction.

STEP 3: SETTING MOTOR LIMITS (The end limits can be set in any order)

For drapery, BRIEFLY PRESS the [OPEN] or [CLOSE] buttons. The drapery will automatically run to record both hard stop positions.

Bring the window covering to the desired upper limit position, then PRESS & HOLD both the [STOP] and [CLOSE] buttons simultaneously until the window covering starts to move.

PRESS the [STOP] button to stop the motor when the desired lower limit position is reached. PRESS the [OPEN] or [CLOSE] button to adjust to the exact position.

PRESS & HOLD both the [STOP] and [OPEN] buttons simultaneously until the window covering starts to move. The window covering will stop at the previously set upper position.

PRESS & HOLD the [STOP] button until the window covering jogs to confirm the limit settings.

Diagram Description: Illustrates setting motor limits. Shows pressing [STOP] + [CLOSE] to move to upper limit, then [STOP] to stop at lower limit, then [OPEN]/[CLOSE] for fine adjustment, then [STOP] + [OPEN] to move to upper limit, and finally [STOP] to confirm.

STEP 4: COMPLETE PROGRAMMING

BRIEFLY PRESS the [PROGRAMMING] button on the front of the keypad. The window covering will jog indicating programming is complete and the keypad is now ready to be used.

Diagram Description: Shows a final press of the "Programming Button" to complete the setup.

Modifying Keypad Programming

For detailed steps on programming, please refer to the pocket programming guide at www.somfypro.com/pocket-programming-guide.

SETTING INTERMEDIATE PREFERRED "MY" POSITION

Stop the window covering at the desired intermediate position, then PRESS & HOLD the [STOP] button until the window covering jogs.

The intermediate position is now confirmed. PRESS the [STOP] button to move the window covering to this position.

Diagram Description: Shows stopping the shade at a desired position and holding the [STOP] button to set it.

MODIFYING THE OPERATION DIRECTION

Move the window covering away from its current upper or lower limit, then PRESS & HOLD both the [OPEN] and [CLOSE] buttons simultaneously until the window covering jogs. This could take up to 10 seconds.

Hold the [STOP] button until the window covering jogs to confirm the change of the operation direction.

Diagram Description: Shows holding [OPEN] + [CLOSE] buttons, then holding [STOP] to confirm direction change.

MODIFYING UPPER/LOWER LIMITS

Move the window covering to its current upper or lower limit, then PRESS & HOLD both the [OPEN] and [CLOSE] buttons simultaneously until the window covering jogs. This could take up to 10 seconds.

Adjust the shade to the new desired limit position with the [OPEN] and [CLOSE] buttons, then PRESS & HOLD the [STOP] button until the window covering jogs to confirm the new limit.

Diagram Description: Shows moving the shade to a limit, holding [OPEN] + [CLOSE], adjusting with [OPEN]/[CLOSE], and holding [STOP] to confirm.

ADJUSTING THE SPEED (Supported motors only)

Move the window covering away from its upper or lower limit, then PRESS & HOLD both the [OPEN], [STOP], and [CLOSE] buttons simultaneously until the window covering jogs and the window covering starts moving. This could take up to 10 seconds.

To increase the speed, PRESS & HOLD the [OPEN] button until the shade jogs. Repeat as needed. To decrease the speed, PRESS & HOLD the [CLOSE] button until the window covering jogs. Repeat as needed.

PRESS & HOLD the [STOP] button until the window covering jogs to confirm the new speed.

Battery Replacement

WARNING: Burn hazard. To avoid the risk of fire, explosion, or burns, DO NOT recharge, disassemble, crush, puncture, or incinerate the battery. Please recycle battery appropriately.

1. Remove the keypad from the wall and disassemble.
2. Slide a new CR2450 battery into the holder and reassemble the keypad.

FCC/IC Information

This device complies with part 15 of the FCC Rules and Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) This device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation.

Contact Information

Somfy Systems, Inc.

New Jersey: 121 Herrod Blvd. Dayton, NJ 08810 T: (800) 22-SOMFY F: (609) 395-1300

Florida: 1200 SW 35th Ave. Boynton Beach, FL 33426 T: (877) 22-SOMFY F: (561) 995-7502

California: 15301 Barranca Parkway Irvine, CA 92618-2201 T: (877) 72-SOMFY F: (949) 727-3510

Somfy ULC

6411 Edwards Blvd Mississauga, ON L5T 2P7 CN: (800) 66-SOMFY F: (905) 564-6446

Website: www.somfypro.com, www.somfypro.ca

Somfy Systems, Inc. © FEB 2023. All brands, products, and trademarks are the property of their respective owners.