Somfy Tilt 50 WireFree RTS Programming and Operation Instructions

STEP 1: Connect Power to Motor

1. Connect a 12V battery wand ? or transformer ? to the motor. Motor should already be installed in the blind.

STEP 2: Initiate Programming

(For use with Telis 1 & 4, DecoFlex 1 – 4, Modulis or Telis 1 Chronis Timer)

For Single Channel Transmitters (Telis 1, Modulis, Telis 1 Chronis Timer or DecoFlex 1):

1. On the transmitter, press and hold the UP ⬆️ and DOWN ⬇️ buttons simultaneously until the blind jogs ? (blind slats have a short up and down tilt movement).

For Multi-Channel Transmitters (Telis 4, DecoFlex 4):

1. Using the channel selector ?️, select the desired channel.
2. On the transmitter, press and hold the UP ⬆️ and DOWN ⬇️ buttons simultaneously until the blind jogs ?.

NOTE: This step cannot be performed if the transmitter has previously been programmed (paired) to the blind.

STEP 3: Check Polarity (blind direction)

NOTE: Must be determined before setting blind limits.

Press and hold the DOWN ⬇️ button and confirm the blind tilts down. Press and hold the UP ⬆️ button and confirm the blind tilts up.

• If blind direction is correct, continue to Step 4.
• If blind direction is not correct (in reverse), press and hold the MY (Stop) ⏹️ button on the transmitter for 2 seconds. The blind will jog ?. Blind direction is now corrected. Blind movement should now correspond to the direction button on the transmitter.

Illustrations show the Telis, Modulis, and DecoFlex devices with arrows indicating button presses for polarity checking.

STEP 4: Setting Limits (slat positions)

Starting with slats in down (closed) position:

1. Press and hold the UP ⬆️ or DOWN ⬇️ button on the transmitter to reach the desired lower limit (slat position).
2. Once the desired lower limit (slat position) is reached, press and hold the MY (Stop) ⏹️ and UP ⬆️ buttons simultaneously until the blind begins to tilt upward, then release.
3. Press the MY (Stop) ⏹️ button when the blind reaches the desired upper limit (slat position). If necessary, adjust the desired slat position with a brief press of either the UP ⬆️ or DOWN ⬇️ button.
4. Once desired upper limit (slat position) is reached, press and hold the MY (Stop) ⏹️ and DOWN ⬇️ buttons simultaneously until the blind begins to tilt downward, then release.
5. Once the blind stops at the previously set lower limit (slat position), press the MY (Stop) ⏹️ button for 2 seconds until the slats jog ?. This confirms both limits (slat positions).

To complete programming, proceed to STEP 5.

Starting with slats in up (closed) position:

1. Press and hold the DOWN ⬇️ or UP ⬆️ button on the transmitter to reach the desired upper limit (slat position).
2. Once the desired upper limit (slat position) is reached, press and hold the MY (Stop) ⏹️ and DOWN ⬇️ buttons simultaneously until the blind begins to tilt downward, then release.
3. Press the MY (Stop) ⏹️ button when the blind reaches the desired lower limit (slat position). If necessary, adjust the desired slat position with a brief press of either the UP ⬆️ or DOWN ⬇️ button.
4. Once desired lower limit (slat position) is reached, press and hold MY (Stop) ⏹️ and UP ⬆️ buttons simultaneously until the blind begins to tilt upward, then release.
5. Once the blind stops at the previously set upper limit (slat position), press the MY (Stop) ⏹️ button for 2 seconds until the slats jog ?. This confirms both limits (slat positions).

To complete programming, proceed to STEP 5.

STEP 5: Completing and Exiting Programming Mode

Using a paperclip ? or pen ?️, press and hold the PROGRAM ⚙️ button on the back of the transmitter until the blind jogs ? once. TRANSMITTER IS NOW MEMORIZED AND PROGRAMMING IS COMPLETE.

NOTE: If power is disconnected from the blind before Step 5 is completed, THE TRANSMITTER WILL NOT BE MEMORIZED to the programmed blind. However, limits (slat positions) will remain programmed. If this occurs, go back and repeat step 2 (Initiate Programming). Then omit step 4 (Setting Limits) and resume with step 5.

Illustrations show the back of a Telis transmitter with the PROGRAM button highlighted, and a DecoFlex switch.

STEP 6: Adding Additional Transmitters or Assigning Channels

Adding Additional Transmitters (single channel):

1. Using a paperclip ? or pen ?️, press and hold the PROGRAM ⚙️ button on the previously addressed transmitter until the blind jogs ? once. OR 1a. Using a paperclip ? or pen ?️, press and hold the PROGRAM ⚙️ button on the motor until the blind jogs ? once.
2. Using a paperclip ? or pen ?️, press and hold the PROGRAM ⚙️ button on the new transmitter until the blind jogs ? once. New transmitter is now added to the shade memory and can be used to operate the blind.

Adding Specific Channels to the Blind (multi-channel transmitters only):

1. Using a paperclip ? or pen ?️, press and hold the PROGRAM ⚙️ button on the previously addressed transmitter until the blind jogs ? once. OR 1a. Using a paperclip ? or pen ?️, press and hold the PROGRAM ⚙️ button on the motor until the blind jogs ? once.
2. Select the desired channel (1-4 or all) by momentarily pressing the Channel Selector ?️ button on the multi-channel transmitter.
3. Press and hold the PROGRAM ⚙️ button on the multi-channel transmitter until the blind jogs ? once. Additional (new) channel is now added to the blinds' memory and can be used to operate the blind.

NOTE: To prevent unwanted Channel/Transmitter assignments when programming blinds within a group, follow step 1a then proceed to step 2.

Deleting Specific Channels/Transmitters

1. Using a paperclip ? or pen ?️, press and hold the PROGRAM ⚙️ button on the previously addressed transmitter until the blind jogs ? once. OR 1a. Using a paperclip ? or pen ?️, press and hold the PROGRAM ⚙️ button on the motor until the blind jogs ? once.
2. Select the desired channel (1-4 or all) or transmitter (single channel) to be deleted.
3. Press and hold the PROGRAM ⚙️ button on the transmitter until the blind jogs ? once. Channel or transmitter is now deleted from the blind memory and will not operate the blind.

STEP 7: Resetting Motor (Erasing all Previously Programmed Limit Settings and Channels)

1. To delete all previous settings: Using a paperclip ?, press and hold the PROGRAM ⚙️ button, located on the top of the motor casing, until the blind jogs ? 3 times (approx. 12 seconds). All transmitters and limits will be erased from the motor memory. Motor is now reset to factory mode. Motor limits (slat positions) will need to be re-established.

Operating Instructions

(For use with Telis 1 & 4, DecoFlex 1 - 4 or Modulis)

USER MODE: Operating the Blind (tilting the slats)

About Somfy

SOMFY® is the leading global manufacturer of strong, quiet motors with electronic and app controls for interior and exterior window coverings. Over 270 million users worldwide enjoy the more than 150 million motors produced by Somfy. During the past 40+ years, Somfy engineers have designed products for both the commercial and residential markets to motorize window coverings such as interior shades, wood blinds, draperies, awnings, rolling shutters, exterior solar screens and projection screens. Somfy motorization systems are easily integrated with security, HVAC and lighting systems providing total home or building automation.

Somfy Systems Inc. Contact Information

SOMFY NORTH AMERICAN HEADQUARTERS
121 Herrod Blvd.
Dayton, NJ 08810
T: (800) 22-SOMFY (76639)
NJ: (609) 395-1300
F: (609) 395-1776

FLORIDA
6100 Broken Sound Pkwy. N.W.
Suite 14
Boca Raton, FL 33487
T: (800) 22-SOMFY (76639)
F: (561) 995-7502

CALIFORNIA
15291 Barranca Parkway
Irvine, CA 92618-2201
T: (800) 22-SOMFY (76639)
F: (949) 727-3775

SOMFY ULC Canada Division
5178 Everest Drive
Mississauga, Ontario L4W2R4
T: 1-800-66-SOMFY (76639)
CN: (905) 564-6446
F: (905) 238-1491

Website: www.somfysystems.com