ACCU-CHEK® Mobile Wireless Adapter

Important Safety Warnings

WARNING / WARNUNG / AVERTISSEMENT / AVVERTENZA / WAARSCHUWING / ADVARSEL / VARNING / VAARA / 警告

• Choking hazard: Small parts. Keep away from children under the age of 3 years.
• Keep new and used batteries away from children. Ingestion or insertion into the body may cause chemical burns, perforation of soft tissues, and death. Severe burns may occur within 2 hours of swallowing. If you think a battery might have been swallowed or placed inside any part of the body, seek medical attention immediately.
• If the battery compartment does not close securely, stop using the product and keep it away from children. Contact Roche.

Overview of Wireless Adapter

The ACCU-CHEK Mobile Wireless Adapter is designed to connect your ACCU-CHEK Mobile meter to a compatible device for data transfer.

Attaching the Wireless Adapter

Follow these steps to attach the wireless adapter to your ACCU-CHEK Mobile meter:

1. Slide the wireless adapter onto the ACCU-CHEK Mobile meter until it clicks into place.
2. Open the battery compartment cover on the adapter.
3. Insert a CR 1632 battery into the compartment, observing correct polarity.

Pairing the Wireless Adapter

Pair the wireless adapter with your ACCU-CHEK Mobile meter for the first time:

1. Turn the wireless adapter ON.
2. Hold the adapter near the ACCU-CHEK Mobile meter.
3. The meter will display a pairing code.
4. Ensure the code on the adapter matches the code on the meter.
5. Confirm the pairing on both devices. A successful pairing is indicated by a checkmark ✔️.
6. Keep the adapter within 1 meter (3.3 feet) of the meter during operation.

Transferring Test Results

Transfer your blood glucose test results wirelessly:

1. Ensure the wireless adapter is ON and the meter is ON.
2. Hold the adapter within 1 meter (3.3 feet) of the meter.
3. The meter will display your test results (e.g., 106 mg/dL / 5.8 mmol/L).
4. The adapter's indicator light will blink during data transfer.
5. A confirmation message will appear on the meter indicating successful data transfer.

Replacing the Battery

The wireless adapter uses one CR 1632 battery:

1. Open the battery compartment cover on the wireless adapter.
2. Remove the old battery.
3. Insert a new CR 1632 battery, ensuring correct polarity (+/-).
4. Close the battery compartment cover securely.

Troubleshooting

If you encounter issues:

1. Ensure the adapter and meter are within the recommended range (less than 1 meter).
2. Try turning the adapter OFF and then ON again.
3. If problems persist, consult the full manual or contact customer support. A question mark ❓ may indicate a need for support.

Precautions and Disposal

PRECAUTION / VORSICHTSMASSNAHME / PRÉCAUTION / PRECAUZIONE / VOORZORGSMAATREGEL / FORHOLDSREGEL / FÖRSIKTIGHETSÅTGÄRD / VAROTOIMENPIDE / 注意

• Used devices carry a risk of infection. Dispose of the used wireless adapter according to local regulations.

Customer Support

For assistance, please refer to the country-specific contact information provided in the original document. General information and support can be found at:

• ACCU-CHEK website: www.accu-chek.com

Specific country contact details include:

• Belgium: 0800-93626
• Denmark: 80 82 84 71
• Germany: 0800 4466800
• France: 0800 27 26 93
• Finland: 0800 92066
• Italy: 800 822 189
• Netherlands: 0800-022 05 85
• Norway: 21 400 100
• Austria: +43 1 277 27-355
• Sweden: 020-41 00 42
• Switzerland: 0800 803 303
• Japan: 0120-642-860