Patents
navify® Portalnavify® Portal
Roche | Worldwide
Instruction Manual for Roche models including: P-N 09804536001 Connect the power supply 4 Optionally Analyzer, P-N 09804536001, Connect the power supply 4 Optionally Analyzer, power supply 4 Optionally Analyzer, supply 4 Optionally Analyzer, Optionally Analyzer, Analyzer
2 Set up the analyzer 3 Connect the power supply 4 Optionally, connect to network 5 Power on the analyzer 6 Log on to the analyz
cobas® liat quick start portal
File Info : application/pdf, 2 Pages, 1.79MB
DocumentDocument2 Set up the analyzer No special setup is required, all software and default settings are preloaded prior to shipment. Analyzer location and operating environment · Place on a level, vibration-free and non-reflective surface, away from direct sunlight. · Allow at least 10 cm (4 in) rear clearance for ventilation and at least 6 cm (2.5 in) front clearance for barcode scanning. · Operating temperature is between 15°C and 32°C (59-90°F), and relative humidity is between 15% and 80%. Operating altitude is up to 2000 metres Mean Sea Level (MSL). · Locate the analyzer near a grounded mains outlet to avoid the power cable being a trip hazard. 3 Connect the power supply CAUTION! Using an inappropriate power supply may cause malfunction. Only use the power supply provided, connected to a voltage of 100-240V AC, 50-60 Hz. · Insert the power supply cable into the analyzer power connector located at its rear. · Connect the power cable to the power supply. Plug the other end of the cable into a properly grounded mains outlet. 4 Optionally, connect to network Connecting the analyzer to the network enables, for example, remote software and assay updates, automatic time/date synchronization (SNTP), and host connectivity. · Connect the Ethernet jack on the rear of the analyzer to an appropriate wall jack using a standard Ethernet data cable with RJ-45 connectors. Refer to the User Guide for information on defining the network environment. 5 Power on the analyzer This initiation process takes a few minutes from power up to display of the log on screen. · Press and release the power button. · The analyzer starts initializing. Wait for initialization to complete. NOTICE Do not insert an assay tube or other items into the analyzer during initialization. Doing so will damage the assay tube and the analyzer. · The Log on screen is displayed when the analyzer is ready for operation. 10 cm 6 cm 6 Log on to the analyzer · Choose the Log on button. · If you first log on to the analyzer after unboxing, enter the pre- defined user ID "ADMIN" and choose the Enter button. · If you first log on after a restart, enter your user ID and choose the Enter button. · If you log on to the analyzer on a routine basis, either enter your user ID and choose the Enter button, or choose the Scan button, and scan the barcode on your User ID card. WARNING! Do not stare into the laser beam. The analyzer is a class 2 laser product. · Enter your password or when prompted, change your password. · On the first log on after unpacking the administrator sets first the Time zone and then the Date and time. It is recommended to keep this sequence! (Settings > System > Date and time). 7 Run an assay Refer to the cobas® liat system User Guide and the package insert or Instructions for Use of the assay for instructions on running an assay. 8 Shut down the analyzer i Always use the shutdown function within the software. Improper shutdown can damage the analyzer! · To log off from the analyzer, choose on the Main screen the Log off button. · On the Log on screen, choose the Shut down button. · Follow the instructions on the screen. · When prompted, power off the analyzer by holding the power button until both the power indicator and the touch screen turn dark. VV-07724-05 9 User documentation Electronic user documentation can be downloaded using the eLabDoc e-service on Roche DiaLog: https://dialogportal.roche.com Alternatively, scan the following QR code: For more information, contact your local affiliate or Roche Service representative. Roche Support | Publication information To obtain technical assistance, contact your local Roche representative. Affiliates: https://www.roche.com/worldwide Patents: http://www.roche-diagnostics.us/patents Roche Molecular Systems, Inc. 1080 US Highway 202 South Branchburg, NJ 08876 USA Made in Switzerland Roche Diagnostics GmbH Sandhofer Strasse 116 68305 Mannheim Germany © 2015-2023 Roche Molecular Systems, Inc. COBAS and LIAT are trademarks of Roche. All other product names and trademarks are the property of their respective owners. Revision history Publication version 12.0 Revision date June 2023 VV-07724-05 P/N 09804536001 cobas® liat analyzer Quick Start Guide This Quick Start Guide is a reference for the cobas® liat analyzer setup. Read the entire cobas® liat system User Guide before using it, or running any cobas® liat assay. Unpacking the analyzer IMPORTANT! Retain the shipping container and packing materials in case you need to return the analyzer to Roche for any reason. · Unpack the analyzer from the shipping container. · Do not apply any force to the door on the top of the unit or to the barcode scanner window. · Do not hold or lift the analyzer from the sample entry door or the barcode scanner window. · Handle with care. Use both hands to support the analyzer along the sides of the base. · Unpack the power supply and other accessories. · Inspect the outer case, front panel buttons, screen, and rear ports for any shipping damage. Check all other items for shipping damage. Report any problems to your local Roche representative. Incident reporting r Inform your Roche representative and your local competent authority about any serious incidents which may occur when using this product. 1 Parts list Documentation cobas® liat analyzer Quick Start Guide cobas® liat system Short Instructions cobas® liat analyzer Cleaning Tool Guide Tube entry door Touch screen Function buttons Navigation buttons Hardware parts cobas® liat analyzer cobas® liat user ID card kit cobas® liat cleaning tool kit Power supply Power cable Touch screen stylus Tube entry door USB ports Power supply Ethernet port Barcode reader Kensington Security Slot Power indicator Power button Power connector