Carlson 2-in-1 Plastic Gate & Pet Pen

Important Safety Information

READ ALL INSTRUCTIONS BEFORE ASSEMBLY AND USE OF GATE.

KEEP INSTRUCTIONS FOR FUTURE USE.

WARNING:

• NOT recommended for use with children.
• Install according to manufacturer's instructions.
• To prevent serious injury or death, securely install gate or enclosure and use according to manufacturer's instructions.
• Children have died or been seriously injured when gates are not securely installed. ALWAYS install and use gate as directed using all required parts.
• Never stack gates on top of each other to form a taller barrier. This could result in serious injury or death.
• Intended for use with children between 6 and 24 months.
• STOP using when a child or pet can climb over or dislodge the gate.
• Use only with the locking/latching mechanism securely engaged.
• To prevent falls, NEVER use at top of stairs.
• NEVER use to keep child or pet away from pool.
• Always ensure the gate is resting against the floor before beginning installation.
• Strangulation hazard: pets can force themselves into very small openings; use this gate with pets whose heads will not fit into openings in the gate, between the gate and floor, or between the gate and wall.
• This product will not necessarily prevent all accidents. NEVER leave child or pet unattended.
• Check the gate regularly to see if all the hardware and mountings are tightened.
• Do not use if any components are missing or damaged.
• Adult assembly required.

Parts List

Please check to make sure you have the following parts:

• A Play Yard Gate Frame (6 Panels)
• B Wall Mounting Bracket (4)
• C Gate Connector (4)
• D 1" Wall Mounting Screws (8) (requires a Phillips/cross-head screwdriver)
• E Small Threaded Gate Cap (1)
• F Tall Gate Cap (2)

Option A: Installing Your Gate Between Two Walls

STEP 1: Unfold the gate frame at each pivoting joint by loosening each cap.

STEP 2: Determine the size of your opening. If you need to remove panels from your gate simply unhook the upper and lower knobs between the panels. If you are adding panels, hook together opposite panel ends; one panel with the male side and one panel with the female side. Check to make sure all the panels are securely locked.

STEP 3: Attach two gate connectors to one of the free ends of your gate at the specified mounting locations shown below. The placement of the gate connectors will determine where your gate is attached to the wall. Repeat step for the other free end of the gate.

STEP 4: With the gate connectors attached to the gate, attach the wall mounting brackets to the gate connectors. Repeat step for opposite end of gate.

STEP 5: Use a Phillips/cross-head screwdriver to fix the wall mounting bracket to the wall. Repeat for all four brackets.

STEP 6: Rotate wall mounting bracket to the locked position. Repeat step for remaining wall mounting brackets.

STEP 7: Arrange the panels to your desired configuration.

NOTE: When putting your gate away you can remove the gate panels without removing the wall mounting brackets.

STEP 8: To remove your gate, rotate all wall mounting brackets to the unlocked position. You are now able to detach the gate connectors from the wall mounting brackets.

NOTE: This gate is designed to fit minimum width openings 36 inches wide to maximum width openings 192 inches wide.

Option B: Installing Your Gate as a Freestanding Enclosure

STEP 1: Unfold the gate frame at each pivoting joint by loosening each cap.

STEP 2: Position the pet pen into your desired configuration, then join the free ends of the pet pen together at the plastic joints.

STEP 3: Tighten the locking knobs to secure your pet pen into your desired configuration.

NOTE: When adding or removing additional panel units to the configuration, panels must be added or subtracted in sets of two for the freestanding enclosure to function properly.

To Fold Your Play Gate

STEP 1: Detach two of the gate panels by unhooking the upper and lower knobs.

STEP 2: You will now be able to pull the pet pen apart.

STEP 3: Fold and put away.

Care and Maintenance

Periodically check the gate for signs of damage, wear, or missing components. Do not use if any part is missing, worn or damaged. Check the gate regularly to ensure all the hardware and mountings are tightened. Do not use abrasive cleaners or bleach. Clean by sponging with warm water and a mild detergent.

90 Days Limited Warranty

If, during the first 90 days after consumer purchase of the item, under reasonable and non-commercial use and conditions of maintenance, it fails while owned by the original purchaser because of the quality of materials or workmanship of finish and assembly, Carlson Pet Products, Inc. will replace or repair it at Carlson's option. PROOF OF PURCHASE REQUIRED.

Contact Information

Website: www.carlsonpetproducts.com

Company: Carlson Pet Products, Inc.

Address: 3200 Corporate Center Drive, Suite 105 | Burnsville, MN 55306, USA

Phone: 952.435.1084

Social Media: @carlsonpetproducts (Facebook, Instagram, Pinterest)