JONSBO TW4-360 ARGB User's Manual

Chapter 1 - Part List

This section details the components included with the JONSBO TW4-360 ARGB CPU Cooler.

• A: CPU Cooler (Also referred to as CPU Kühler, Ventirad, CPU 쿨러, CPU散热器)
• B: Fan (Also referred to as Ventilator, Ventilateur, 팬 (FAN), 风扇)
• C: Backplate (Also referred to as Backplate, Backplate, 백플레이트, 背板)
• D: Intel Bracket (Also referred to as Intel Halterung, Intel Bracket, 인텔 브랫킷, 英特尔支架)
• E: AMD Bracket (Also referred to as AMD Bracket, AMD Halterung, AMD 브랫킷, AMD支架)
• F: AMD Bracket (Duplicate listing, likely referring to a different AMD bracket or a typo)
• G1: Screw (Also referred to as Schraube, Vis, 나사, 螺丝) - Quantity: 4
• G2: Thermal Paste (Also referred to as Wärmeleitpaste, Pâte thermique, 써멀 페이스트, 散热膏)
• G3: Screw (Quantity: 4)
• G4: Screw (Quantity: 4)
• G5: Screw (Quantity: 4)
• G6: Screw (Quantity: 4)
• G7: Fan (Quantity: 3)
• G8: Screw (Quantity: 4)
• H: Y-Cable (Also referred to as Y-Kabel, Câble en Y, Y- 케이블선, Y-转接线)

Chapter 2 - Installation

This section provides step-by-step instructions for installing the JONSBO TW4-360 ARGB CPU Cooler.

Step 1: Install the Intel / AMD bracket

Instructions:

• Intel: Install the Intel bracket (D) onto the motherboard.
• AMD: Install the AMD bracket (E/F) onto the motherboard.

Notes:

• Ensure the correct bracket is used for your CPU socket type (Intel or AMD).
• For Intel LGA 1700, a specific backplane (A) and screws (B) are used. Place the LGA1700 backplane on the back of the motherboard.

Step 2: Apply thermal paste and prepare the cooler

Instructions:

• Apply thermal paste (G2) to the CPU surface.
• Remove the protective film from the cooler's contact surface.

Step 3: Secure the cooler

Instructions:

• Intel LGA 2011/1366/115X/1200/775:
• Place the cooler onto the CPU.
• Secure the cooler by tightening the screws (G1/G3/G4/G5/G6) diagonally.
• AMD:
• Remove the plastic retainers from the AMD retention module.
• Place the cooler onto the CPU.
• Secure the cooler by tightening the screws.

Step 4: Connect the fan and pump cables

Instructions:

• Connect the 3-pin connector from the pump unit to the AIO/PUMP socket on the motherboard.
• Connect the 4-pin PWM fan connectors using the Y-cable (H) to the CPU_FAN socket on the motherboard.

RGB/ARGB Connections:

• For ASUS motherboards, connect to the 5V AURA socket.
• For GIGABYTE motherboards, connect to the 5V VDG socket.
• If your motherboard does not have a 5V aRGB socket, connect to the SATA POWER socket to enable the rainbow light effect automatically.

Step 5: Mount the fans and radiator

Instructions:

• Secure the fans (G7) and the radiator to the computer case.

Intel LGA1700 Installation Guide (12th Gen)

This section provides specific instructions for installing the cooler on Intel 12th Gen LGA1700 sockets.

Step 1: Prepare the backplane

Place the LGA1700 backplane (A) on the back of the motherboard.

Step 2: Secure the pump unit

Diagonally tighten the screws to secure the pump unit.