Bormann Elite Solar LED Floodlights

I. Operation Mode

The Bormann Elite Solar LED Floodlights are available in models ranging from 50W to 400W.

• Solar Charging Time: 5-8 hours, depending on location and temperature.
• Discharge Mode: The light operates with decreasing brightness over time: 100% in the first hour, 80% in the second, 60% in the third, 50% in the fourth, and 30% in the fifth to sixth hour. It remains on until dawn, then switches to charging mode.
• Operating Time Options: 3H, 5H, 8H.
• Brightness Adjustment Mode: Controlled via the remote control.
• Recommended Mode: Automatic mode "AUTO" for best results.
• Default Mode: Automatic mode is selected by default when the device is switched on.
• Automatic Mode Function: The lamp's brightness adapts automatically based on the battery's power level.

Component Identification:

The solar floodlight setup includes the following components:

• 1. Solar Panel
• 2. Aluminium Alloy
• 3. Tempered Glass
• 4. Ventilation
• 5. Outlet
• 6. Remote Control

Diagram Description: A visual representation shows the solar panel connected to the floodlight unit via a cable, with the remote control nearby. Components are numbered for identification.

II. Important Safety Information

• Do not dispose of the battery in fire, as this may result in an explosion.
• Do not expose the light to fire or intense heat, as the battery may explode.
• Do not immerse the unit in water.
• Never look directly into the light or shine it into another person's eyes.
• Consult your local construction guide if necessary for installing the light fixture in a building.

III. Fixing Instructions

• The light fixture must be installed on a flat and stable surface.
• Avoid installing the light near air conditioners, central heaters, or high-voltage systems.
• Position the solar charger board in a sunny area to maximize sunlight collection. Typically, the solar board should face south, receiving at least 3 hours of sunlight daily (5 hours if behind glass).
• It is recommended to charge the light for 24 hours before its first use.
• Periodically (at least once a year), clean the charger board with a soft, damp cloth to prevent reduced power output due to accumulated dust.

IV. Installation

Follow these steps for installation:

1. Fix the bracket of the solar panel. (Diagram shows bracket being attached to a surface.)
2. Remove the bracket from the lamp body and fix it. (Diagram shows bracket detachment from lamp and reattachment to a mounting surface.)
3. Fix the lamp body to the bracket. (Diagram shows lamp body being attached to the bracket.)
4. Adjust the angle as needed. (Diagram shows adjusting the angle of the mounted lamp.)
5. Connect the wire of the solar panel to the wire of the lamp. (Diagram shows wire connection.)

V. Remote Control Introduction

The remote control allows for various lighting adjustments:

• [ON]: Turn on the light.
• [OFF]: Turn off the light.
• [M] (Brightness Control): Full brightness, Increase brightness, Reduce brightness, Half brightness.
• Automatic Night Activation: The light turns on automatically at night via light control.
• Timer Functions:
  • Turn on after dark, automatically close after 3 hours.
  • Turn on after dark, automatically close after 5 hours.
  • Turn on after dark, automatically close after 8 hours.

Quick Setup Procedure:

WARNING:

• 1. Please keep it away from children.
• 2. For outdoor use only.

Note 1: Alternative/Newer remote control version: Press the key "AUTO/WAKE UP" to activate the lamp before the first time use.

Note 2: Keys "3H", "5H", "8H" can have a different layout.

VI. Technical Data

VII. Environmental Protection

Protect the environment. Your appliance contains valuable materials which can be recovered or recycled. Please leave it at a specialized institution.

This symbol ♻️ indicates separate collection for electrical and electronic equipment required under the WEEE Directive (Directive 2012/19/EC) and is effective only within the European Union.

Manufacturer Information and Warranty

The manufacturer reserves the right to make minor changes to product design and technical specifications without prior notice, unless these changes significantly affect the performance and safety of the products. Parts described/illustrated may concern other models. For safety, reliability, and warranty validity, all repair, inspection, or replacement work must be carried out by authorized service technicians. Always use supplied equipment; non-provided equipment may cause malfunctions or injury. The manufacturer and importer are not liable for injuries or damages from non-conforming equipment.

The warranty covers free replacement of components with manufacturing defects or material failure. In case of unavailability of a spare part, the company may replace the appliance with a corresponding model. Warranty period is not extended or renewed after replacement. Replacement parts with repair charges are covered by a 1-year warranty, provided warranty terms are met. Replaced parts remain company property. Greek law applies to this warranty.