PARKSIDE Cordless Reciprocating Saw PSSA 20-Li A1

Product Overview and Features

The PARKSIDE PSSA 20-Li A1 cordless reciprocating saw is designed for sawing, cutting to length, and fitting wood, plastic, metal, or construction materials. It is suitable for rough sawing, straight and curved cuts, and flush cutting.

Included Accessories:

• 1x PARKSIDE Cordless Reciprocating Saw PSSA 20-Li A1
• 1x Saw blade for wood (BIM 152.5 mm, SWISS MADE)
• 1x Carry case
• 1x Operating Manual

Technical Data:

* Battery and charger are not included in the scope of delivery.

Note on Vibration: The stated vibration level is measured according to a standardized method and can be used for comparison. It may also serve as an initial assessment of exposure. The actual vibration level can vary depending on usage and may be higher than stated. Minimize vibration exposure by wearing gloves and limiting work time.

Safety Instructions

General Safety for Power Tools

• Work Area Safety: Keep the work area clean and well-lit. Avoid working in explosive atmospheres. Keep children and bystanders away.
• Electrical Safety: Ensure plugs fit sockets. Do not modify plugs. Avoid body contact with earthed surfaces. Keep tools dry. Do not carry by the cord. Use suitable extension cords for outdoor use. Use a residual current device (RCD) in damp conditions.
• Personal Safety: Stay alert and use common sense. Do not operate when tired or under the influence of substances. Wear personal protective equipment (PPE) such as safety glasses, dust masks, and gloves. Avoid accidental starting by ensuring the tool is off before connecting the battery or picking it up. Remove the battery before making adjustments or changing accessories. Keep tools out of reach of children and untrained persons. Maintain tools properly; sharp cutting tools are easier to control.
• Proper Use: Do not overload the tool. Use the correct tool for the job. Do not use tools with faulty switches.
• Battery Tool Usage: Only charge batteries with the recommended charger. Do not expose batteries to heat, fire, water, or moisture, as this can cause explosions. Keep batteries away from metal objects like paper clips or coins to prevent short circuits. If battery fluid leaks, rinse with water and seek medical attention if necessary.

Specific Safety for Reciprocating Saws:

• Hold the tool by insulated gripping surfaces when performing operations where the cutting tool may contact hidden wiring. Contact with a live wire can energize exposed metal parts and cause electric shock.
• Always wear a dust mask.

Safety for Chargers:

• This device can be used by children aged 8 and above, and by persons with reduced physical, sensory or mental capabilities, if supervised or instructed on safe use and understand the resulting hazards. Children must not play with the device. Cleaning and user maintenance must not be performed by children without supervision.
• If the mains cable is damaged, it must be replaced by the manufacturer or their customer service to avoid hazards.
• The charger is intended for indoor use only.

Saw Blade Information:

• Use any saw blade with the correct 1/2" (12.7 mm) universal shank. Blades optimized for specific tasks are available.
• TPI = Teeth Per Inch (number of teeth per 2.54 cm).
• Wood saw blades (e.g., 152.5 x 0.9 mm, 6-12 TPI) are suitable for construction wood, panel, and plywood, including plunge cuts.

Before Use

Charging the Battery Pack (See Fig. A):

• Always unplug the charger before inserting or removing the battery pack.
• Do not charge batteries at temperatures below 10°C or above 40°C.
• For long-term storage of a lithium-ion battery, regularly check the charge level. The optimal charge level is between 50% and 80%. Store in a cool, dry environment (0°C to 50°C).
• Insert the battery pack into the fast charger.
• Plug the charger into the socket. The red charge indicator LED will light up.
• The green charge indicator LED will light up when charging is complete and the battery pack is ready for use.

Caution: If the red LED blinks, the battery pack is overheated and cannot be charged. If both red and green LEDs blink, the battery pack is defective.

Inserting/Removing the Battery Pack:

• To Insert: Slide the battery pack into the device until it clicks into place.
• To Remove: Press the release button and remove the battery pack.

Checking Battery Status:

• Press the battery status button. The battery display LED indicates the charge level:
• RED / ORANGE / GREEN = Full charge
• RED / ORANGE = Medium charge
• RED = Low charge - charge the battery.

Operation

Mounting/Changing the Saw Blade:

WARNING: Remove the battery before any work on the tool (e.g., maintenance, accessory changes), transport, or storage. Accidental activation of the ON/OFF switch can cause injury.

• Turn the quick-release chuck to the stop and hold it in position.
• Insert the required saw blade until it stops in the chuck.
• CAUTION: The teeth of the saw blade must point downwards!
• Release the quick-release chuck; it should return to its original position. The saw blade is now locked.

Adjusting the Shoe Plate:

WARNING: Turn off the device and remove the battery before any work on the unit.

• Adjust the shoe plate according to the desired cutting depth.
• Loosen the locking lever, position the shoe plate, and then tighten the locking lever to secure the position.

Adjusting Pendulum Action:

• The pendulum action can be adjusted using the pendulum action switch.
• Setting "0" (No Pendulum Action): For fine and clean cut edges. Recommended for thin workpieces.
• Setting "I" (Pendulum Action): For faster cutting progress.

Starting and Stopping:

• To Start: Press the lock-off switch, then press the ON/OFF switch. Release the lock-off switch.
• To Stop: Release the ON/OFF switch.

Adjusting Speed:

• Light pressure on the ON/OFF switch results in low speed. Increasing pressure increases the speed.
• The integrated motor brake ensures a quick stop.

Safe Handling of the Reciprocating Saw:

• The shoe plate is pivotable for adapting to the workpiece and for secure support. It must always rest against the workpiece during operation.

Cutting Tips:

• Check the material for foreign objects like nails or screws and remove them.
• Ensure ventilation slots are not obstructed.
• Turn on the tool before bringing it to the workpiece.
• If the saw blade jams, immediately turn off the tool. Spread the cut with a suitable tool and pull out the saw.
• Match the saw blade and stroke rate to the material being cut.
• Use appropriate saw blades for different applications.
• Saw with consistent feed pressure.

Flush Cutting:

• With flexible saw blades, you can cut protruding workpieces (e.g., pipes) flush against a wall.
• Position the saw blade directly against the wall.
• Bend the saw slightly with lateral pressure so the shoe plate rests against the wall.
• Switch on the tool and cut the workpiece with constant pressure.

Plunge Cutting:

CAUTION: RECOIL HAZARD! Plunge cuts should only be performed in soft materials (wood, etc.).

• Place the saw with the underside of the shoe plate onto the workpiece. Turn on the tool.
• Tilt the saw forward and plunge the blade into the workpiece.
• Position the saw vertically and continue cutting along the line.

Maintenance and Cleaning

WARNING: RISK OF INJURY! Turn off the device and remove the battery before any work.

• Keep the device clean, dry, and free from oil or grease.
• Use a dry cloth to clean the housing.
• Replace the saw blade when it becomes dull and no longer allows for clean sawing.
• Keep the device and ventilation slots clean. Blocked slots can lead to overheating or damage.
• Clean the device after finishing work.
• Do not allow liquids to enter the device. Use a cloth for cleaning. Never use petrol, solvents, or cleaners that attack plastic.
• Clean the saw blade holder with a brush or compressed air if necessary.
• For long-term storage of a lithium-ion battery, regularly check the charge level. Optimal charge is 50-80%. Optimal storage climate is cool and dry.

Warranty

Kompernaß Handels GmbH provides a 3-year warranty from the date of purchase. This warranty does not affect your statutory rights as a consumer.

• The warranty period begins on the purchase date. Keep your original receipt as proof of purchase.
• If a material or manufacturing defect occurs within three years of purchase, the product will be repaired or replaced free of charge at our discretion.
• To claim warranty service, the defective device and proof of purchase must be presented, along with a description of the defect and when it occurred.
• Repairs or replacements do not extend the warranty period.
• Existing damages or defects must be reported immediately after unpacking. Repairs after the warranty period are subject to charge.

Warranty Exclusions: The warranty does not cover normal wear and tear, consumable parts (e.g., switches, batteries), or damage to fragile parts or parts made of glass. The warranty is void if the product is damaged, misused, or improperly maintained. Use of the product for purposes advised against in the manual or unauthorized modifications will void the warranty. The product is intended for private use only; commercial use or improper handling voids the warranty.

Service and Support

For quick processing of warranty claims or service inquiries:

• Keep your receipt and the article number (e.g., IAN 290825) ready.
• Contact the service department by phone or email.
• Send defective items without accessories (e.g., battery, case) to the provided service address.
• Further manuals, product videos, and software can be downloaded from www.lidl-service.com.

Service Contact Information:

• Germany: Tel: 0800 5435 111, Email: kompernass@lidl.de
• Austria: Tel: 0820 201 222 (0.15 EUR/Min.), Email: kompernass@lidl.at
• Switzerland: Tel: 0842 665566 (0.08 CHF/Min.), Email: kompernass@lidl.ch

Importeur:

KOMPERNASS HANDELS GMBH
BURGSTRASSE 21
DE - 44867 BOCHUM
GERMANY
www.kompernass.com

Disposal

• The packaging is made of environmentally friendly materials and can be disposed of at local recycling points.
• Do not dispose of power tools in household waste! According to European Directive 2012/19/EU, electrical tools must be collected separately and recycled environmentally.
• Do not dispose of batteries in household waste! Defective or used batteries must be recycled according to Directive 2006/66/EC. Return battery packs and/or devices via collection points.
• Dispose of packaging environmentally. Observe the labeling on packaging materials and separate them if necessary.
• For disposal options for obsolete products, contact your local municipality or city administration.

Declaration of Conformity

KOMPERNASS HANDELS GMBH declares that this product complies with relevant EU directives and harmonized standards, including the Machinery Directive (2006/42/EC), Low Voltage Directive (2014/35/EU), EMC Directive (2014/30/EU), and RoHS Directive (2011/65/EU).

Machine Designation: Cordless Reciprocating Saw PSSA 20-Li A1

Manufacturing Year: 02-2018

Serial Number: IAN 290825

Date: Bochum, 01.02.2018

Technical modifications in the interest of further development are reserved.

Ordering Spare Batteries

Replacement batteries can be ordered conveniently online at www.kompernass.com or by phone. The price for a replacement battery is €20 (incl. VAT and shipping).

Online Ordering:

• Visit www.kompernass.com.
• Select your country and language.
• Navigate to the "Accessories Shop" and find the appropriate replacement battery.
• Add to cart and follow the checkout process.

Note: If online ordering is not available in your country, contact the service hotline.

Telephone Ordering:

• Contact the respective service numbers provided for Germany, Austria, or Switzerland.
• Have the article number (IAN 290825) ready for faster processing.