Parkside PASSK 20-Li A1 Cordless Impact Wrench

Introduction

Congratulations on the purchase of your new Parkside device. This operating manual is part of the product and contains important information regarding safety, use, and disposal. Familiarize yourself with all operating and safety instructions before using the product. Use the product only as described and for the intended applications. Pass on all documentation when transferring the product to third parties.

Intended Use

The device is designed for screwing in and loosening screws, as well as tightening and loosening nuts. It features right/left rotation, a 1/2" external square tool holder, and an LED work light to illuminate the immediate work area. The impact function converts motor power into uniform rotational impacts, engaging during tightening and loosening. The device is intended for adult use; supervised use by individuals over 16 years is permitted. The manufacturer is not liable for damages caused by misuse or incorrect operation. The device is not intended for commercial use. Any other use or modification is considered non-intended and carries significant accident risks.

Features

• 1. Tool Holder (1/2" square drive)
• 2. Direction of Rotation Switch / Lock
• 3. Belt Clip
• 4. Battery Status Button
• 5. Battery Display LED
• 6. Battery Pack
• 7. Battery Pack Release Button
• 8. LED Work Light
• 9. Torque Selection Button
• 10. ON / OFF Switch / Speed Control
• 11. Sockets (17/19/21/23 mm)
• 12. Fast Charger
• 13. Red Charge Control LED
• 14. Green Charge Control LED

Scope of Delivery

• 1x Parkside Cordless Impact Wrench PASSK 20-Li A1
• 4x Sockets (17/19/21/23 mm)
• 1x Belt Clip
• 1x Carrying Case
• 1x Operating Manual

Technical Data

Battery and Charger Compatibility

For operating the cordless tool, use only the following battery: PAP 20 A2* (Lithium-Ion, 20V, 3Ah, 10 cells). For charging, use only the following fast charger: PLG 20 A2* (Input: 230-240V~50Hz, 85W; Output: 21.5V DC, 3.5A; Charging time: approx. 60 min; Protection Class II). *Battery and charger are not included in the scope of delivery.

The battery is compatible with all devices of the "PARKSIDE X 20 V TEAM" series.

Battery voltage: 20V max. (discharges to 18V).

Noise and Vibration Emissions

Measured according to EN 60745:

• Sound Pressure Level (LPA): 91.6 dB(A), Uncertainty K: 3 dB
• Sound Power Level (LWA): 102.6 dB(A), Uncertainty K: 3 dB
• Vibration Total Value (a_h) for screw/nut tightening (max. permissible size): 8.65 m/s², Uncertainty K: 1.5 m/s²

Wear hearing protection! ?

The specified vibration level is measured using a standardized method and can be used for comparison. It can also be used for initial exposure assessment. Vibration levels may vary during actual use. Minimize exposure by wearing gloves and limiting work time.

General Safety Instructions for Power Tools

Read all safety instructions and guidelines. Failure to follow these may result in electric shock, fire, or serious injury. Keep all instructions for future reference. The term "power tool" refers to mains-powered or battery-powered tools.

1. Workplace Safety

• Keep your work area clean and well-lit. Clutter and poor lighting can lead to accidents.
• Do not operate power tools in explosive atmospheres where flammable liquids, gases, or dust are present. Power tools create sparks that can ignite dust or vapors.
• Keep children and other persons away from the work area. Distractions can lead to loss of control.

2. Electrical Safety

• Ensure the power tool's plug fits the socket. Do not modify the plug. Avoid using adapter plugs with earthed tools. Unmodified plugs and matching sockets reduce the risk of electric shock.
• Avoid body contact with earthed surfaces (pipes, radiators, stoves, refrigerators). Increased risk of electric shock if your body is earthed.
• Keep power tools away from rain or moisture. Water ingress increases the risk of electric shock.
• Do not misuse the cable for carrying, hanging, or unplugging. Keep the cable away from heat, oil, sharp edges, or moving parts. Damaged or tangled cables increase the risk of electric shock.
• When working outdoors, use only extension cords suitable for outdoor use. This reduces the risk of electric shock.
• If operation in damp environments is unavoidable, use a residual current device (RCD). This reduces the risk of electric shock.

3. Personal Safety

• Stay attentive, use common sense, and work responsibly. Do not use power tools when tired or under the influence of drugs, alcohol, or medication. A moment of inattention can lead to serious injury.
• Wear personal protective equipment (PPE), including safety glasses ?. PPE such as dust masks, non-slip footwear, safety helmets, or hearing protection, depending on the tool and its use, reduces the risk of injury.
• Avoid unintentional starting. Ensure the tool is switched off before connecting to power or battery, picking it up, or carrying it. Carrying the tool with a finger on the switch or connecting it while switched on can cause accidents.
• Remove adjustment tools or wrenches before switching on the power tool. A tool left in a rotating part can cause injury.
• Maintain a stable stance and balance at all times. This allows for better control of the power tool in unexpected situations.
• Wear appropriate clothing. Avoid loose clothing or jewelry. Keep hair, clothing, and gloves away from moving parts. Loose items can be caught by moving parts.

Tool Usage and Handling

• Do not overload the tool. Use the appropriate power tool for your work. Using the correct tool ensures better and safer performance within its specified range.
• Do not use a power tool with a defective switch. A tool that cannot be switched on or off is dangerous and requires repair.
• Disconnect the plug and/or remove the battery before making any adjustments, changing accessories, or storing the tool. This prevents unintentional starting.
• Store unused power tools out of the reach of children. Do not allow persons unfamiliar with the tool or these instructions to use it. Power tools are dangerous in the hands of inexperienced users.
• Maintain power tools with care. Check for misalignment or binding of moving parts, breakage, or any other condition that may affect the tool's operation. Have damaged parts repaired before use. Many accidents are caused by poorly maintained power tools.
• Keep cutting tools sharp and clean. Sharp, well-maintained cutting tools jam less and are easier to guide.
• Use power tools, accessories, and bits according to these instructions, considering the working conditions and the task. Using power tools for applications other than their intended purpose can lead to hazardous situations.

Battery Tool Usage and Handling

• Charge batteries only with chargers recommended by the manufacturer. Using a charger intended for a specific battery type with other batteries can pose a fire hazard.
• Use only the intended batteries in the power tools. Using other batteries can lead to injuries and fire hazards.
• Keep unused batteries away from paper clips, coins, keys, nails, screws, or other small metal objects that could bridge the contacts. Short-circuiting the battery contacts can cause burns or fire.
• Battery fluid may leak if misused. Avoid contact. If contact occurs, rinse with water. If fluid gets into eyes, seek medical attention. Leaking battery fluid can cause skin irritation or burns.

CAUTION! EXPLOSION HAZARD! ?

Never attempt to recharge non-rechargeable batteries.

Protect the battery from heat, e.g., from prolonged sunlight, fire, water, and moisture. There is an explosion hazard.

Service

Have your power tools repaired only by qualified personnel using original spare parts. This ensures the safety of the power tool is maintained.

Specific Safety Instructions for Impact Wrenches

• Wear hearing protection ? when impact wrenching. Noise exposure can cause hearing loss.
• Secure the workpiece. A workpiece held by clamping devices or a vice is held more securely than by hand.
• Hold the power tool firmly. High reaction torques can occur briefly when tightening and loosening screws.
• Wait until the power tool has come to a complete stop before setting it down. The accessory tool can jam and lead to loss of control.
• Hold the tool by the insulated grip surfaces when performing work where the screw or accessory tool may contact hidden electrical lines. Contacting a live line can also energize metal tool parts and cause electric shock.

Safety Instructions for Chargers

This device can be used by children aged 8 years and above, and by persons with reduced physical, sensory, or mental capabilities or lack of experience and knowledge, if they are supervised or have been instructed in the safe use of the device and understand the resulting hazards. Children must not play with the device. Cleaning and user maintenance must not be carried out by children without supervision.

If the mains connection cable of this device is damaged, it must be replaced by the manufacturer, its customer service, or a similarly qualified person to avoid hazards.

The charger is only suitable for indoor use.

If the mains connection cable of this device is damaged, it must be replaced by the manufacturer, its customer service, or a similarly qualified person to avoid hazards.

CAUTION! HOT SURFACE. RISK OF BURNS. ?

Before Operation

Battery Pack Charging (See Fig. A)

CAUTION! Always unplug the mains adapter before removing or inserting the battery pack from/into the charger.

• Never charge the battery pack if the ambient temperature is below 10°C or above 40°C.
• Insert the battery pack into the fast charger (see Fig. A).
• Plug the mains adapter into the socket. The control LED lights up red ?.
• The green control LED indicates that charging is complete and the battery pack is ready for use. ?

CAUTION!

• If the red control LED flashes, the battery pack is overheated and cannot be charged.
• If the red and green control LEDs flash simultaneously, the battery pack is defective.
• Slide the battery pack into the tool.
• Switch off the charger for at least 15 minutes between successive charging cycles. Unplug the mains adapter to do this.

Battery Pack Insertion / Removal

Battery Pack Insertion:

• Set the direction of rotation switch to the middle position (lock) ⚙️. Slide the battery pack into the grip until it clicks into place.

Battery Pack Removal:

• Press the release button and remove the battery pack.

Checking Battery Status

To check the battery status, press the battery status button (see main illustration). The charge status is indicated by the battery display LED as follows:

• RED / ORANGE / GREEN = Full charge ?
• RED / ORANGE = Medium charge
• RED = Low charge - charge battery

Operation

Switching On / Off

Switching On:

• To start the tool, press and hold the ON/OFF switch.
• The LED work light illuminates when the ON/OFF switch is pressed lightly or fully. This allows illumination of the work area in poor lighting conditions.

Switching Off:

• Release the ON/OFF switch to turn off the tool.

Setting / Selecting Speed / Torque

• Press the torque selection button to select the desired torque step-by-step.
• Light pressure on the ON/OFF switch results in low speed/torque. Increasing pressure increases speed/torque.
• The tightening torque depends on the selected speed/torque setting and the impact duration.

NOTE For tightening wheel nuts, the lowest torque setting should be used to avoid overtightening.

CAUTION! The actual achieved tightening torque should always be checked with a torque wrench! ?

The integrated motor brake ensures quick stopping. ?

Changing Direction of Rotation

Change the direction of rotation by pressing the direction of rotation switch to the right or left.

Attaching a Socket

Attach one of the supplied sockets to the tool holder.

Maintenance and Cleaning

WARNING! RISK OF INJURY! Switch off the tool and remove the battery before performing any work on the device. ⚠️

• The tool is maintenance-free.
• The tool must always be kept clean, dry, and free of oil or grease.
• Do not allow any liquids to enter the device.
• Use a dry cloth to clean the housing. Never use petrol, solvents, or cleaners that attack plastic.
• If a lithium-ion battery is to be stored for a long period, its charge status must be checked regularly. The optimal charge status is between 50% and 80%. The optimal storage climate is cool and dry.

NOTE Spare parts not listed (e.g., carbon brushes, switches) can be ordered via the service hotline.

Warranty of Kompernaß Handels GmbH

Dear Customer, you receive a 3-year warranty on this device from the date of purchase. In case of defects, you have statutory rights against the seller. These statutory rights are not restricted by our warranty.

Warranty Conditions

The warranty period begins on the date of purchase. Please keep the original sales receipt safe, as it is required as proof of purchase. If a material or manufacturing defect occurs within three years of the purchase date, the product will be repaired or replaced by us free of charge, at our discretion. This warranty service requires that the defective device and the proof of purchase (receipt) are presented within the three-year period, along with a brief written description of the defect and when it occurred. If the defect is covered by our warranty, you will receive the repaired or a new product back. Repair or replacement does not start a new warranty period.

Warranty Period and Statutory Warranty Claims

The warranty period is not extended by the warranty service. This also applies to replaced and repaired parts. Any damages and defects present at the time of purchase must be reported immediately after unpacking. Repairs after the warranty period has expired are chargeable.

Warranty Scope

The device has been carefully manufactured according to strict quality guidelines and conscientiously checked before delivery. The warranty covers material or manufacturing defects. This warranty does not cover product parts subject to normal wear and tear, consumable parts, or damage to fragile parts such as switches, batteries, or glass components.

This warranty is void if the product is damaged, used improperly, or not maintained. For proper use, all instructions in the operating manual must be followed precisely. Uses and actions advised against or warned against in the manual must be strictly avoided.

The product is intended for private use only, not for commercial use. Misuse, improper handling, force, or unauthorized modifications will void the warranty.

Handling Warranty Claims

For quick processing of your request, please follow these instructions:

• For all inquiries, please have your sales receipt and the article number (e.g., IAN 12345) ready as proof of purchase.
• The article number can be found on the type plate, an engraving, the cover page of your manual (bottom left), or as a sticker on the back or underside.
• If functional errors or other defects occur, please contact the service department mentioned below by phone or email first.
• You can then send a product identified as defective postage-free to the provided service address, along with the proof of purchase (receipt) and a description of the defect and when it occurred.

You can download this and many other manuals, product videos, and software from www.lidl-service.com.

Service

WARNING! Have your devices repaired only by the service center or a qualified electrician using original spare parts. This ensures the safety of the device is maintained.

Always have the replacement of the plug or mains cable carried out by the device manufacturer or their customer service. This ensures the safety of the device is maintained.

Service Contact Information

• DE Service Deutschland: Tel.: 0800 5435 111 (Toll-free from German landline/mobile network) E-Mail: kompernass@lidl.de
• AT Service Österreich: Tel.: 0820 201 222 (0.15 EUR/Min.) E-Mail: kompernass@lidl.at
• CH Service Schweiz: Tel.: 0842 665566 (0.08 CHF/Min., Mobile max. 0.40 CHF/Min.) E-Mail: kompernass@lidl.ch
• IAN 309644

Importer

Please note that the following address is not a service address. Please contact the named service center first.

KOMPERNASS HANDELS GMBH
BURGSTRASSE 21
DE - 44867 BOCHUM
GERMANY
www.kompernass.com

Disposal

The packaging is made from environmentally friendly materials and can be disposed of via local recycling points. ♻️

Do not dispose of power tools in household waste! ?️

According to European Directive 2012/19/EU, used electrical and electronic equipment must be collected separately and subjected to environmentally sound recycling.

Do not dispose of batteries in household waste! ?

Remove batteries from the device before disposal. Defective or used batteries must be recycled according to Directive 2006/66/EC. Return battery packs and/or devices via the provided collection facilities. For information on disposal options for obsolete power tools/battery packs, please contact your local municipality or city administration.

Dispose of packaging ecologically. Observe the markings on the various packaging materials and separate them if necessary. Packaging materials are marked with abbreviations (a) and numbers (b) with the following meaning: 1-7: Plastics, 20-22: Paper and cardboard, 80-98: Composite materials.

Information on disposal options for the obsolete product can be obtained from your local municipality or city administration.

Declaration of Conformity

We, KOMPERNASS HANDELS GMBH, Document Controller: Mr. Semi Uguzlu, BURGSTR. 21, DE - 44867 BOCHUM, GERMANY, hereby declare that this product complies with the following standards, normative documents, and EC Directives:

• Machinery Directive (2006/42/EC)
• EC Low Voltage Directive (2014/35/EU)
• Electromagnetic Compatibility (2014/30/EU)
• RoHS Directive (2011/65/EU)*

*The sole responsibility for issuing this declaration of conformity lies with the manufacturer. The object of the declaration described above complies with the provisions of Directive 2011/65/EU of the European Parliament and of the Council of 8 June 2011 on the restriction of the use of certain hazardous substances in electrical and electronic equipment.

Applied Harmonised Standards:

• EN 60745-1:2009/A11:2010
• EN 60745-2-2:2010
• EN 60335-1:2012/A11:2014
• EN 60335-2-29:2004/A2:2010
• EN 62233:2008
• EN 55014-1:2017
• EN 55014-2:2015
• EN 61000-3-2:2014
• EN 61000-3-3:2013
• EN 50581:2012

Type / Device Designation: Cordless Impact Wrench PASSK 20-Li A1

Year of Manufacture: 08-2018

Serial Number: IAN 309644

Bochum, 18.07.2018

Semi Uguzlu - Quality Manager - Technical changes in the interest of further development are reserved.

Ordering Replacement Batteries

If you wish to order a replacement battery for your device, you can do so conveniently online at www.kompernass.com or by phone. This item may sell out quickly due to limited stock.

NOTE The ordering of spare parts may not be available online in some countries. In such cases, please contact the service hotline.

The promotion is limited to one battery per customer/device and a duration of two months after the promotion period. The replacement battery can continue to be ordered as a spare part under different conditions thereafter.

Telephone Ordering

• DE Service Deutschland: Tel.: 0800 5435 111 (Toll-free from German landline/mobile network)
• AT Service Österreich: Tel.: 0820 201 222 (0.15 EUR/Min.) E-Mail: kompernass@lidl.at
• CH Service Schweiz: Tel.: 0842 665566 (0.08 CHF/Min., Mobile max. 0.40 CHF/Min.) E-Mail: kompernass@lidl.ch

To ensure quick processing of your order, please have the article number (e.g., IAN 309644) of the device ready for all inquiries. The article number can be found on the type plate or the cover page of this manual.