Immax NEO Smart Indoor Socket with USB-C PD and Zigbee

Manufacturer and Importer

IMMAX, Teslova 1179/2, 702 00 Ostrava-Přívoz, EU
www.immaxneo.cz | www.immaxneo.com
Made in P.R.C.

Product Description

Immax NEO Smart indoor socket with pin, type E, 1xUSB, 1xUSB C, PD 20W, Zigbee

Technical Specifications

Warning: CAUTION: The phase wire (L) is connected to the right socket.

LED Indicator Description

• LED lights up red: the socket is in the ON state
• LED is off: the socket is OFF
• LED is flashing green: the socket is in pairing mode

LED notification of power on or off may vary depending on individual settings in the app.

Device Reset

Press and hold the On/Off button on the socket for at least 10 seconds until the LED indicator starts flashing green.

Socket Installation

Important Safety Information!

Installation and maintenance of the device must only be performed by qualified electrical personnel. Do not touch the device terminals during testing. Turn off all household power before installation. Ensure the power source is off before connecting or disconnecting any additional equipment. Always use a properly rated voltage sensing device to ensure that the power is off.

Wiring Connections:

• Connect the phase wire (brown) to the L connector.
• Connect the neutral wire (blue) to the N connector.
• Connect the protective conductor Pe (green-yellow) to the connector with the grounding symbol [grounding symbol].

The Immax NEO PRO smart gateway serves as a hub for communication between your mobile device and other smart devices communicating on the Zigbee 3.0 protocol. Any other use is considered inappropriate. Claims arising from improper use or unauthorized modification of the product will be considered invalid. Any such use is at your own risk.

Pairing Immax NEO LED Light Sources with the Immax NEO App on Mobile Devices

Note: Minor discrepancies may occur in Android and iOS app versions (e.g., slightly different commands or icons), but the principle of operation remains the same. Firmware updates may alter application functionality.

Start-up and Pairing:

1. Connect the socket to the mains.
2. If the LED indicator on the socket is not flashing, press the On/Off button for at least 10 seconds.
3. Ensure the LED indicator on the socket is flashing quickly.
4. The device is ready for pairing.
5. Open the Immax NEO PRO application.
6. Click the "Room" icon.
7. Click the "+" icon to add a new device.
8. Select the Immax NEO category in the left column.
9. Choose "Smart socket (zigbee)" from the offered products.
10. Select the smart gateway with which you want to pair this device (required if you have multiple Immax NEO PRO smart gateways).
11. Click the "Next step" icon [next step icon].
12. Confirm that the LED indicator is flashing quickly.
13. Click the "Next step" icon [next step icon].
14. Wait for the device to be properly paired with the Immax NEO PRO smart gateway.
15. Enter the device name.
16. Select the room where you want the device to be located.
17. Click "Done".

Unpairing a Device from the Immax NEO PRO Smart Gateway

1. Open the Immax NEO PRO app.
2. Click the "Room" icon.
3. Select the device you want to unpair.
4. Click the "Settings" icon in the upper right corner.
5. Click "Remove device".
6. Choose one of the options:
   a) Disconnect: Removes the device from the Immax NEO PRO app, but device information remains stored in the Immax NEO cloud.
   b) Disconnect and erase data: Removes the device from the Immax NEO PRO app and the Immax NEO cloud.
7. Confirm device removal.

Safety Information

WARNING: Keep out of reach of children. This product contains small parts that can cause choking or injury if swallowed.

WARNING: Batteries can release harmful chemicals that may damage skin, clothing, or storage areas. Avoid contact with eyes and skin. Batteries may rupture or explode if exposed to fire or excessive heat. Handle batteries with care.

• Do not use different brands and types of batteries in the same device.
• Always replace all batteries in the device when replacing them.
• Do not use rechargeable or reusable batteries.
• Do not allow children to install batteries without supervision.
• Follow the battery manufacturer's instructions for proper handling and disposal.

WARNING: The product and batteries should be disposed of at a recycling center. Do not dispose of with normal household waste.

WARNING: For safe use, ensure wiring at the installation site complies with regulations. Installation must be performed only by a person with appropriate electrical certification. Always disconnect the power cable before installation or if a fault is detected (turn off the circuit breaker for direct connections). Incorrect installation can lead to product damage and injury.

WARNING: Do not disassemble the product; risk of electric shock.

WARNING: Use only the original power adapter supplied with the product. Do not operate if the power cable shows signs of damage.

WARNING: Follow the instructions in the enclosed manual.

Maintenance

Protect the device from contamination and dirt. Wipe the device with a soft cloth; do not use rough or coarse material. DO NOT use solvents or other aggressive cleaners or chemicals.

Declaration of Conformity

A Declaration of Conformity has been issued for this product. More information can be found at www.immax.cz.

Abridged version of the Declaration of Conformity

Hereby, the manufacturer IMMAX declares that the radio equipment type 07800L is in compliance with Directive 2014/53/EU. The full text of the EU Declaration of Conformity is available on the following websites: www.immax.cz, www.immax.eu. Safety information for this product can be downloaded from www.immax.cz.

Contact

If you have any questions or need advice, please contact us at podpora@immaxneo.cz.

Notes

The [Recycle symbol] symbol indicates that the product must not be disposed of with municipal waste. For proper disposal, hand it in at designated collection points. When disposing of the device, remove batteries and bulbs. Hand in old devices at designated collection points; they do not belong in the municipal waste stream. Waste electrical and electronic equipment from private households can be handed in free of charge at public collection points. As the end user, you are responsible for erasing personal data from your old device.

ASEKOL: AK-016010, WEEE-Reg.-Nr. DE 88927148