Important Safety Instructions
[high-voltage] Terminals marked with this symbol carry electrical current of sufficient magnitude to constitute risk of electric shock. Use only high-quality professional speaker cables with 1/4" TS or twist-locking plugs pre-installed. All other installation or modification should be performed only by qualified personnel.
[warning] This symbol, wherever it appears, alerts you to the presence of uninsulated dangerous voltage inside the enclosure - voltage that may be sufficient to constitute a risk of shock.
[warning] This symbol, wherever it appears, alerts you to important operating and maintenance instructions in the accompanying literature. Please read the manual.
[caution] To reduce the risk of electric shock, do not remove the top cover (or the rear section). No user serviceable parts inside. Refer servicing to qualified personnel.
[caution] To reduce the risk of fire or electric shock, do not expose this appliance to rain and moisture. The apparatus shall not be exposed to dripping or splashing liquids and no objects filled with liquids, such as vases, shall be placed on the apparatus.
[caution] These service instructions are for use by qualified service personnel only. To reduce the risk of electric shock do not perform any servicing other than that contained in the operation instructions. Repairs have to be performed by qualified service personnel.
General Safety Guidelines:
- Read these instructions.
- Keep these instructions.
- Heed all warnings.
- Follow all instructions.
- Do not use this apparatus near water.
- Clean only with dry cloth.
- Do not block any ventilation openings. Install in accordance with the manufacturer's instructions.
- Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.
- Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding-type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.
- Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.
- Use only attachments/accessories specified by the manufacturer.
- Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.
- Unplug this apparatus during lightning storms or when unused for long periods of time.
- Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.
- The apparatus shall be connected to a MAINS socket outlet with a protective earthing connection.
- Where the MAINS plug or an appliance coupler is used as the disconnect device, the disconnect device shall remain readily operable.
- Correct disposal of this product: [recycle] This symbol indicates that this product must not be disposed of with household waste, according to the WEEE Directive (2012/19/EU) and your national law. This product should be taken to a collection center licensed for the recycling of waste electrical and electronic equipment (EEE).
- Do not install in a confined space, such as a book case or similar unit.
- Do not place naked flame sources, such as lighted candles, on the apparatus.
- Please keep the environmental aspects of battery disposal in mind. Batteries must be disposed-of at a battery collection point.
- Use this apparatus in tropical and/or moderate climates.
Legal Disclaimer
MUSIC Tribe accepts no liability for any loss which may be suffered by any person who relies either wholly or in part upon any description, photograph, or statement contained herein. Technical specifications, appearances and other information are subject to change without notice. All trademarks are the property of their respective owners. MIDAS, KLARK TEKNIK, LAB GRUPPEN, LAKE, TANNOY, TURBOSOUND, TC ELECTRONIC, TC HELICON, BEHRINGER, BUGERA and COOLAUDIO are trademarks or registered trademarks of MUSIC Group IP Ltd. © MUSIC Group IP Ltd. 2018 All rights reserved.
Limited Warranty
For the applicable warranty terms and conditions and additional information regarding MUSIC Tribe's Limited Warranty, please see complete details online at music-group.com/warranty.
Hook-up
Step 1: Hook-Up
Power Connection direct to LIVE MINI: Connect the supplied power adapter to the power input on the LIVE MINI.
Power Connection using the LIVE MINI charging base (recommended): Place the LIVE MINI on the charging base. Connect the supplied power adapter to the charging base. This method is recommended to reduce wear on the power connector.
Bluetooth Connection to LIVE MINI: Pair your Bluetooth-enabled device with the LIVE MINI.
Auxiliary Connection to LIVE MINI: Connect an audio source (e.g., MP3 player) to the Aux Input on the rear of the LIVE MINI using a 3.5 mm TRS cable.
LIVE MINI Controls
Step 2: Controls
Top Panel Controls:
- 1. Previous: Press to play the previous song in the playlist.
- 2. Microphone Aperture: For phone calls and voice interaction. Keep clean and dry.
- 3. Next: Press to play the next song in the playlist.
- 4. Power ON/Battery Indicator: Shows battery status (Green: >50%, Yellow: 20%-50%, Red: Low). When charging, shows charging progress (Solid Green: Full, Slow Yellow Flash: >Halfway, Slow Red Flash:
- 5. Power Button: Press once to turn on. Press and hold for ~1 second to turn off.
- 6. [volume-down] Button: Used for volume down and other operations.
- 7. Multi-Function Button (MFB): Used for Pause, Play, and call handling.
- 8. [volume-up] Button: Used for volume up and other operations.
- 9. Aux Input Indicator: Illuminates when connected to an auxiliary device via the 3.5 mm Aux connector.
- 10. Bluetooth Button: Used for Bluetooth pairing.
- 11. Bluetooth Indicator: Shows the status of the Bluetooth connection.
Rear Panel Connectors:
- 12. Aux Input: 3.5 mm TRS connector for line-level stereo input from external devices (MP3 players, computers).
- 13. Power Input: Connector for the supplied power adapter to charge the internal battery. Can be used directly or via the charging base.
- 14. Power Connector: Spring terminals on the charging base for connecting to the LIVE MINI.
- 15. Power Input (on charging base): Connector for the supplied power adapter to charge the LIVE MINI when placed on the base.
LIVE MINI Getting started
Step 3: Getting started
Overview
This guide helps set up the LIVE MINI, highlighting its capabilities including premium transducers, bass radiator design, Bluetooth connectivity, and 3.5 mm aux input for versatile connection options.
Power Connections
Ensure the LIVE MINI is fully charged before first use. Use only the supplied power adapter. Connect directly to the LIVE MINI's rear power connector or to the charging base. Place the charging base on a clean, dry, flat surface and ensure the LIVE MINI is correctly fitted. The Power LED indicates charging status. Do not leave unattended while charging. Turn off the adapter when charging is complete. The battery is not user-replaceable.
Battery Notes
The internal battery is Li-ion. To maximize battery life, avoid running the battery to very low charge. Recharge from a medium charge level. Playing time varies with volume and music type. High temperatures can affect battery life; avoid placing the LIVE MINI near heat sources or in direct sunlight. For long-term storage, ensure the unit is charged. Unplug the adapter when not in use.
Operations Table
Summarizes key operations for Bluetooth and Aux modes.
A2dp profile connected HFP connected HFP connected| Function Name | Status | Operation | Remark | LED Status |
|---|---|---|---|---|
| Turn On | Off | Press and hold POWER button until Power LED lights up | Connects to last used device or enters pairing mode. | Power LED ON for 10 seconds (shows battery status: Green >50%, Yellow 20%-50%, Red: Low). |
| Turn Off | On | Press and hold POWER button until Power LED turns red and then off | Power LED Off | |
| Show battery status | On | Press POWER button for 3 seconds | Power LED turns on for 3 seconds. | Power LED color shows charge status. |
| Bluetooth mode (BT=Bluetooth, MFB=Multi-Function Button) | ||||
| Enter pairing | On, but not in call-active state | Hold BT button for 3 seconds | LIVE MINI is ready for pairing and connecting. Expires in 5 minutes. | BT LED flashes blue slowly |
| Manual Connection Request | Idle state | Press MFB button | LIVE MINI starts to connect to the last used device. | No change |
| BT connection established | BT LED On steady | |||
| Volume Up | Music playing or a call is active | Press '+' button | BT LED flashes once | |
| Volume Down | Music playing or a call is active | Press '-' button | BT LED flashes once | |
| Volume maximum/ minimum | Music playing or a call is active | Press and hold the + or - buttons | Keeps increasing or decreasing volume. | BT LED flashes twice |
| Play/Pause music player | Press MFB once | BT LED flashes once | ||
| Forward | Audio streaming | Press NEXT button | Jump to next song | BT LED flashes once |
| Backward | Audio streaming | Press PREV button | Jump to previous song | BT LED flashes once |
| Incoming call | Incoming call | Press MFB once | BT LED On steady | |
| Answer a call | Incoming call | Press MFB once | BT LED flashes | |
| Reject an incoming call | Incoming call | Hold MFB for 1 second | No change | |
| End/cancel a call | Call active | Press MFB once | No change | |
| Last number redial | Press MFB twice | No change | ||
| Voice dial | Press MFB three times | No change | ||
| Three way call | Incoming call on hold | Press MFB twice | No change | |
| Accept waiting release active | Second call on hold/waiting | Press MFB once | No change | |
| Accept waiting hold active | Second call on hold/waiting | Press MFB twice | No change | |
| Accept held incoming call | Incoming call on hold | Press MFB once | No change | |
| Reject held incoming call | Incoming call on hold | Hold MFB for 1 second | No change | |
| Three way call | Call on hold/waiting | Press MFB+BT buttons | Release all held | No change |
| Add held to 3 way | Call on hold/waiting | Double press MFB+BT buttons | No change | |
| Reset Bluetooth paired device list | Idle state | Hold '+' & '-' together for 5 seconds | Resets BT paired device list | BT LED flashes several times |
| AUX mode | ||||
| Volume up | AUX mode | Press '+' button | AUX LED flashes once | |
| Volume down | AUX mode | Press '-' button | AUX LED flashes once | |
| Volume maximum/ minimum | AUX mode | Press and hold the + or - buttons | Keeps increasing or decreasing volume. | AUX LED flashes twice |
| Mute/unmute | AUX mode | Press MFB | AUX LED flashes once | |
| Switch BT mode | AUX mode | Press BT button or Unplug the 3.5mm jack | Changes to BT LED indicator. | Change to BT led |
| Switch AUX mode | BT mode | Plug in 3.5mm jack | AUX LED ON | |
| Battery Status | ||||
| Full charged | Any state | Plug in charger | POWER LED Green steady | |
| > 50% full | Any state | Plug in charger | POWER LED slowly flashing Yellow | |
| < 50% full | Any state | Plug in charger | POWER LED slowly flashing Red | |
Note: LIVE MINI will automatically turn itself off if there is no audio input for 20 minutes.
Specifications
| Performance | |
|---|---|
| Audio output power (Stereo) | 2 x 8 Watts RMS @ 4 Ohms |
| Transducers | 2 x 1.75" with neodymium magnets |
| Passive radiators | 2 x Oval Shape Radiators 3.3" x 1.5" |
| Aux input | 3.5 mm TRS |
| Power Requirements | |
|---|---|
| External power adapter input | 100-240 VAC 50/60 Hz |
| External power adapter output | 5 VDC, 2 A maximum |
| Internal Battery | |
|---|---|
| Type | Li-ion |
| Rating voltage | 7.4 V |
| Capacity | 2600 mAh |
| Bluetooth Wireless Technology | |
|---|---|
| Version | Bluetooth 4.2 |
| RF frequency range | 2402 to 2480 MHz |
| Channel No. | 79 |
| Maximum output power | 10 dBm |
| Environmental | |
|---|---|
| Operating temperature range | 5°C to 40°C (41°F to 104°F) |
| Physical | |
|---|---|
| Dimensions (H x W x D) | 63 x 186 x 65 mm (2.5 x 7.3 x 2.6") |
| Weight | 0.89 kg (1.96 lbs) |
Other important information
1. Register online.
Please register your new MUSIC Tribe equipment right after you purchase it by visiting behringer.com. Registering your purchase using our simple online form helps us to process your repair claims more quickly and efficiently. Also, read the terms and conditions of our warranty, if applicable.
2. Malfunction.
Should your MUSIC Tribe Authorized Reseller not be located in your vicinity, you may contact the MUSIC Tribe Authorized Fulfiller for your country listed under “Support” at behringer.com. Should your country not be listed, please check if your problem can be dealt with by our “Online Support” which may also be found under “Support” at behringer.com. Alternatively, please submit an online warranty claim at behringer.com BEFORE returning the product.
3. Power Connections.
Before plugging the unit into a power socket, please make sure you are using the correct mains voltage for your particular model. Faulty fuses must be replaced with fuses of the same type and rating without exception.
FEDERAL COMMUNICATIONS COMMISSION COMPLIANCE INFORMATION
TANNOY LIVE MINI
Responsible Party Name: MUSIC Tribe Commercial NV Inc.
Address: 5270 Procyon Street, Las Vegas, NV 89118 USA
Phone Number: +1 702 800 8290
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
This equipment complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
- This device may not cause harmful interference, and
- This device must accept any interference received, including interference that may cause undesired operation.
This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
[caution] The MUSIC Group is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment. Such modifications could void the user authority to operate the equipment.
FCC RF Radiation Exposure Statement:
- This Transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
- This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20 centimeters between the radiator and your body.
