General Recommendation for Installation
We recommend having accessory parts fitted by a specialist workshop. Nous vous recommandons de faire monter vos pièces par un atelier spécialisé. É consigliabile fare eseguire il montaggio dei componenti applicati da un'officina specializzata. Recomendamos que el montaje de los componentes se realice en un taller especializado.
Important Symbols and Notes
- ⚠️ Caution / Attention / Attenzione / Atención: Important safety or operational notice.
- ? Note / Remarque / Nota / Observaciones: General information or tips.
- ⚠️ Warning / Avertissement / Avvertenza / Advertencia: Warning of potential risks or hazards.
- ? Liquid: Refers to fluids.
- ? Torque: Indicates tightening torque values.
- ? Template: Refers to a template for marking or cutting.
- ??? 2 Persons: Indicates that two people are recommended for the task.
- ?️ Original Motorcycle Part: Refers to a genuine part from the motorcycle manufacturer.
Torque Specifications
Standard tightening torques in Nm for bolted connections with strength class 8.8 and for stainless steel (Inox A2). For special tightening torques, refer to your specialist workshop.
| Bolt Size | Steel 8.8 (Nm) | Inox A2 (Nm) |
|---|---|---|
| M 4 | 2,7 | 0,8 |
| M 5 | 5,5 | 1,7 |
| M 6 | 9,7 | 3,0 |
| M 8 | 23,0 | 7,9 |
| M 10 | 47,0 | 14,0 |
| M 12 | 80,0 | 24,0 |
| M 14 | 130,0 | -,- |
| M 16 | 196,0 | 59,0 |
| M 18 | 270,0 | -,- |
| M 20 | 385,0 | 114,0 |
Apply conventional lubricant to stainless steel bolts prior to assembly.
Important Installation Notes & Warnings
These instructions are written based on our current state of knowledge. Information is provided without any guarantee as to its accuracy. Subject to technical modifications.
The order of assembly steps must be followed.
Touratech accepts no liability for incorrectly fitted parts and resulting material damage or personal injury!
Please observe applicable road vehicle (construction and use) regulations as well as EC/ECE Directives and applicable laws in your country. If parts are fitted which require inspection and/or approval after fitting, take your vehicle to a testing station immediately and have the vehicle papers updated.
Check and if necessary tighten all bolted connections after 50 km.
Please take into account that fitting panniers, crash bars, foot peg lowering kits (rider and pillion), Kickstand enlargement plate, front spoilers and engine guards may restrict the bike's lean angle! ?️
If modifications are made to the fairing, stem, handlebar, fairing parts, etc., ensure that electrical wiring, brake lines, accelerator and clutch cables are refitted correctly. Check clearance, both sides with full steering lock.
Always disconnect the battery when working on the electrics! ?
We recommend cutting protective film to size and applying it to impact areas that are likely to be chipped by stones. ?️
Work on the brake system and suspension should always be carried out by a specialist workshop. ?️
Maximum load on luggage racks is 5 kg! Luggage racks ZegaPro TC is 10 kg!
If other original accessories or aftermarket accessories are used, ensure clearance, fitment and do not come into contact with other parts!
PDF fitting instructions are also available for download from the Touratech webshop.
Product: Side Stand Base Extension
Part Number: 01-037-5277-0
For: BMW R1250GS / R1250GS Adventure for low suspension
Assembly Instructions
This section describes the assembly process based on the provided diagrams.
Step 1: Preparation
Align the new side stand base extension with the original side stand base on the motorcycle.
Step 2: Apply Foam Rubber
Apply the provided foam rubber to the designated area on the new base extension. This may help with damping or fit.
Step 3: Attachment
Attach the new base extension, now with the foam rubber, to the motorcycle's side stand. Secure it using the provided bolts and nuts. Ensure all connections are snug.
Step 4: Final Check
The assembly is complete. Ensure the side stand operates correctly and the extension is securely fastened.
Note: A small icon shows a motorcycle with a rider and a warning symbol (?️⚠️), indicating caution is advised when using the side stand or during riding after installation.
