HoneyGuardian Automatic Pet Feeder User Manual

Contents

• Safety Precautions
• Warranty
• Package Contents
• Product Diagram
• Button and Control Panel Explanation
• How to Use
• Preparation Before Assembly and Setup
• Setup Instructions
• Cleaning and Maintenance
• Troubleshooting

Safety Precautions

Warnings

• Dispose of all packaging materials properly. Some products may be packaged in plastic bags; these bags pose a suffocation risk, so keep them out of reach of children and pets.
• To reduce the risk of injury, supervise children closely when using the device near them.
• Do not immerse the base in water, as this may damage electronic components such as the control panel.
• Do not use this product outdoors. Periodically check the condition of the equipment to ensure it is functioning properly.
• Do not use wet food or canned food.
• Only use accessories recommended or sold by the manufacturer. Using accessories not recommended or sold by the manufacturer may lead to dangerous situations.
• Do not modify the pet feeder.
• Always unplug the power cord when not in use or when cleaning.
• Check the automatic pet feeder after installation. If there are water droplets on the power cord or plug, do not plug it in.
• To prevent tripping, place the power cord in a location that does not obstruct access.

Precautions

• Ensure pets do not chew or swallow parts. If you are concerned about the power cord, purchase a cord conduit (hard plastic protector) to protect it.
• Do not install or store the pet feeder in locations with temperatures below 4°C (39.2°F).
• Use alkaline D-cell batteries.
• Check the batteries regularly. When leaving for an extended period, be sure to replace them with new batteries.
• This product is designed for dry food with kibble sizes between 2-15mm in diameter. Kibble larger than this may cause blockages in the food outlet.
• Read and follow all precautions listed on this product and its packaging.

Warranty

• 1-Year Limited Warranty
• Lifetime Support
• For guidance on product usage and warranty extensions, please contact the brand's after-sales service representative via email at: service@honeyguardian.com
• If you have any questions about your order, please contact the seller through the shopping platform.

Package Contents

• 1x Automatic Pet Feeder
• 2x Stainless Steel Bowls OR 2x Slow Feeder Bowls
• 2x Bowl Bases
• 1x Power Adapter
• 1x Desiccant Bag
• 1x User Manual

Product Diagram

Front View

• 1. Desiccant Box
• 2. Lid
• 3. Lid Release Button
• 4. Food Bucket Lock
• 5. Feeder Base
• 6. Food Outlet
• 7. Bowl Base
• 8. Control Panel
• 9. LCD Display
• 10. Food Bucket
• 11. Battery Cover
• 12. Speaker
• 13. Power Outlet

Bottom View

Button and Control Panel Explanation

• MEAL Button: Press and hold for 3 seconds to turn the device on/off. Press to cycle through feeding counts (1-6 times).
• Portion Button: Set the feeding portion size (0-24 portions).
• Manual Feed Button: Dispense one portion of food with a single press.
• 12H Button: Set the hour (0-23).
• 60M Button: Set the minute (0-59).
• Time Button: Enter time setting mode and save the time setting.
• Record Button: Record, play back, and delete recordings.

How to Use

Preparation Before Assembly and Setup

1. Press the lid release button and remove accessories from the food jar.
2. Place the desiccant bag under the lid inside the box.
   • Note: To prevent mold, it is recommended to replace the desiccant every 15 days. Remove the desiccant bag before cleaning the cover.
3. Attach the bowl base. Align the bowl with the designated notch under the base of the automatic pet feeder.
   • Note: Before moving the feeder, press the bottom of the food bowl to detach it from the feeder base. If the food bowl contains food, carry it carefully to avoid spilling. When lifting the feeder, hold the base and not other parts.
4. Add dry pet food to the food tank.
   • Note: Do not use wet food or canned food.
   • Recommended kibble diameter range: 2-15mm.
5. Close the lid. Press down firmly to ensure it clicks into place.

Connecting the Power

This product supports two power methods:

• Insert the power cord into the power jack under the automatic feeder and plug the 5V power adapter into a power outlet.
• Open the battery cover on the bottom of the main unit and install three D-cell alkaline batteries (not included) as a backup in case of power outage. The LCD display will light up, indicating the automatic feeder is on.
  • Note: D-cell alkaline batteries not included.
  • Ensure all parts are clean and dry before connecting the power.
  • Batteries must supply 5V output for power. The battery level icon on the display will flash when the battery is low.

Setup Instructions

1. Setting the Current Time

1. Press and hold the Time Button ⏱️ for 3 seconds to enter time setting mode. The time display will flash.
2. Press the Hour Button 12H to set the hour, and press it again to increase the hour by one. Press the Minute Button 60M to set the minute, and press it again to increase the minute by one. Press and hold the buttons to adjust the time quickly.
3. Press and hold the Time Button ⏱️ for 3 seconds to save the current time and finish the time setting.

2. Setting Feeding Times and Portion Sizes

1. Set the time for Meal 1 after setting the current time. Press the MEAL button ?️ to enter the feeding plan settings. The feeding count "1", feeding time, and portion size will flash. Use the Hour Button 12H and Minute Button 60M to set the feeding time.
2. Set the portion size for Meal 1. Press the Portion Button ? to set the feeding amount.
   • Note: Set a maximum of 24 portions per meal.
3. After setting Meal 1, press the MEAL button ?️ to continue setting the feeding plan for Meal 2. You can continue to set subsequent feeding plans. Up to 6 meals per day can be set. To not feed at the next scheduled time or to delete a previous feeding setting, set the portion size to "0".

3. Clearing All Settings

Press and hold the Manual Feed Button ✋ and the Time Button ⏱️ simultaneously for 3 seconds to reset the settings.

Reference for Portion Settings

• 1 Portion = 15ml = 0.06 Cups = 6g (Weight may vary depending on kibble)

Note: Each bowl can be allocated to a portion of food.

4. Recording Settings

• Press and hold the Record Button ? for 3 seconds until the recording light turns on to start recording. You can record up to 10 seconds. Release your finger during recording to stop. After stopping recording, press the Record Button ? again to play the recording.
• To delete existing recordings, quickly press the Record Button ? twice. The recording light will flash 3 times.

5. Manual Feeding for Pets

• Press and hold the Manual Feed Button ✋ for 3 seconds. The automatic feeder will dispense one portion of food into each bowl.

6. Low Power Display

• When the internal batteries are low, the display panel will show a battery icon ?. After replacing the batteries, the battery icon will disappear. (Battery Model: D-cell Alkaline Batteries)

Cleaning and Maintenance

For your pet's health, it is recommended to clean the automatic feeder regularly.

The cleanable parts are as follows: Lid, food bucket, stainless steel bowls, bowl base.

Washing the Lid, Food Bucket, and Bowl Base

1. Before cleaning, turn off the power and remove the batteries.
2. Open the lid and remove the desiccant from the box under the lid.
3. Push down on the bowl base to remove it.
4. Remove the food bucket. Press the latches on both sides with your thumb while lifting simultaneously.
5. Before reinstalling the machine, ensure the lid, food bucket, and bowl base are dry.
6. When attaching the bucket, check the direction of the arrow on the rubber rotor at the bottom. The arrows on both sides must align.

Troubleshooting

Specifications

A303D

A305D