Lucci PIER LED 12V Deck Light Installation Guide

Product Overview

This document provides installation instructions for the Lucci PIER LED 12V Deck Light with VERSION 2 connector.

SKU Numbers: 220450, 220451, 220453, 220454

Rated Voltage: 12V

This luminaire is rated 12V and classified as Extra Low Voltage (ELV). It is designed for DIY installation and does not require complex electrical connections or disconnections. It is crucial not to plug this luminaire directly into a 240V supply. For any work involving 240V, a licensed electrician is required. Assistance from a technical person with appropriate tools may be necessary for a complete installation.

The Lucci wiring kit (SKU# 220826, 220827) and Lucci transformer (SKU# 220818, 220819, 220829) are sold separately.

Please read and follow all instructions carefully before assembly, installation, and use for correct function and safety. Keep these instructions for future reference.

Warranty

• This luminaire is covered by a 3-year warranty from the date of purchase (not installation).
• Retain proof of purchase for any warranty inquiries.
• This luminaire is not suitable for use with dimmer switches.
• Warranty will be void if used on a circuit with a dimmer switch.
• Warranty will be void if damage occurs due to improper usage or modification.
• Failure to comply with these instructions may increase the risk of damage or injury and will void the warranty.

Installation Requirements

• All wiring and installation must adhere to the latest local and national wiring rules (e.g., AS/NZS 3000 Electrical installations). Consult a licensed electrician if unsure.
• Replace any cracked protective lamp shade to maintain the luminaire's IP rating.
• Location Selection:
  • Suitable for deck installation only; not for ceiling or wall installations.
  • The luminaire is protected against water penetration to IP65 standards (jets of water from any direction), which must be maintained during installation.
  • The wiring kit and connectors are not suitable for underground installation without protection from water or damp conditions. Position them where water can drain easily; they are not designed for immersion.
  • Consider a gravel substrate at the installation location to aid water drainage and prevent wiring from being submerged after rain or watering.
  • The mounting point must support at least twice the weight of the luminaire.
• Handle electrical wires with care during unpacking to avoid damaging connections.
• Lay out all components on a smooth surface and verify all parts are present before assembly. Return incomplete products to the place of purchase.
• Inspect the luminaire for damage during transport. Do not install or operate a damaged product; return it for inspection, repair, or replacement.
• Ensure power to the circuit is switched OFF before commencing any electrical work.

Installation Directions

Installing the Deck Light with Springs

1. Remove the luminaire from its packaging.
2. Install the springs onto the luminaire by tightening the screws on both sides. (Refer to Diagram A)
3. Cut an installation hole of Ø36mm into the mounting point. (Refer to Diagram B)
4. Connect the luminaire to the Lucci wiring kit (SKU# 220826, 220827 - sold separately). Ensure the connector is fully tightened. (Refer to Diagram C) Note: The wiring kit is rated for a maximum 80VA load.
5. Install the luminaire into the installation hole. (Refer to Diagram C)
6. Connect the Lucci wiring kit (SKU# 220826, 220827 - sold separately) to the Lucci transformer (SKU# 220818, 220819, 220829 - sold separately). (Refer to Diagram D) Note: Do not exceed the load ratings of the wiring kit (80VA) and transformer (28VA and 10VA options).
7. Insert the plug into a mains power socket outlet (not included) and ensure it is fully plugged in. (Refer to Diagram D)
8. After installation, switch on the luminaire to test all lighting functions. (Refer to Diagram E)

Diagram A: Shows attaching the springs to the luminaire by tightening screws on both sides.

Diagram B: Illustrates cutting an installation hole of Ø36mm into the mounting point.

Diagram C: Depicts connecting the luminaire to the Lucci wiring kit and installing it into the prepared hole.

Diagram D: Shows connecting the Lucci wiring kit to the Lucci transformer and plugging the transformer into a 240V mains power socket outlet.

Diagram E: Illustrates switching on the luminaire after installation to test its functions.

Installing the Deck Light with Moulded Box

1. Remove the luminaire from its moulded box packaging. (Refer to Diagram A)
2. Cut an installation hole of Ø39mm into the mounting point. (Refer to Diagram B)
3. Install the moulded box into the installation hole.
4. Connect the luminaire to the Lucci wiring kit (SKU# 220826, 220827 - sold separately). Ensure the connector is fully tightened. (Refer to Diagram C) Note: The wiring kit is rated for a maximum 80VA load.
5. Install the luminaire into the moulded box. (Refer to Diagram C)
6. Insert the plug into a mains power socket outlet (not included) and ensure it is fully plugged in. (Refer to Diagram D)
7. Connect the Lucci wiring kit (SKU# 220826, 220827 - sold separately) to the Lucci transformer (SKU# 220818, 220819, 220829 - sold separately). (Refer to Diagram D) Note: Do not exceed the load ratings of the wiring kit (80VA) and transformer (28VA and 10VA options).
8. Insert the plug into a mains power socket outlet (not included) and ensure it is fully plugged in. (Refer to Diagram D)
9. After installation, switch on the luminaire to test all lighting functions and enjoy your new luminaire. (Refer to Diagram E)

Diagram A: Shows removing the luminaire from its moulded box.

Diagram B: Illustrates cutting an installation hole of Ø39mm into the mounting point.

Diagram C: Depicts connecting the luminaire to the Lucci wiring kit and installing it into the moulded box.

Diagram D: Shows connecting the Lucci wiring kit to the Lucci transformer and plugging the transformer into a 240V mains power socket outlet.

Diagram E: Illustrates switching on the luminaire after installation to test its functions.

Safety Tips

• Always ensure power is OFF and the luminaire has cooled down before performing any maintenance, cleaning, or adjustment.
• The external flexible cable or cord cannot be replaced; if damaged, the luminaire must be destroyed.
• Do not use the luminaire if the protective shield is cracked. Replace any cracked shield before use.
• The light source is not replaceable; the entire luminaire must be replaced when the light source reaches its end of life.
• To prevent injury or damage, ensure power leads and screws are secure before connecting power.
• Clean by wiping with a soft damp cloth. Do NOT soak or immerse the luminaire in water or other liquids.
• Ensure the luminaire does not contact corrosive chemicals, solvents, or abrasive cleaners.

Specifications