Lucci PIER LED 12V Deck Light Installation Guide

Important Notes

This installation guide applies to the 12V side of the luminaire. The Lucci PIER LED 12V Deck Light is rated 12V and classified as Extra Low Voltage (ELV). It is designed for DIY installation and does not require direct electrical connection or disconnection from mains voltage. Never plug this luminaire directly into a 240V supply. For any work involving 240V, a licensed electrician is required. Assistance from a qualified technician with appropriate tools may be necessary for installation.

The Lucci wiring kit (SKU# 220826, 220827) and Lucci transformer (SKU# 220818, 220819, 220829) are sold separately and are required for operation.

Please read and follow all instructions carefully before assembly, installation, and use of this luminaire to ensure correct function and safety. Keep these instructions for future reference.

Warranty Information

• This luminaire is covered by a 5-year warranty from the date of purchase, not the date of installation.
• Please retain proof of purchase for any warranty enquiries.
• This luminaire is not suitable for use with dimmer switches.
• Warranty will be void if the luminaire is used on a circuit with a dimmer switch.
• Warranty will be void if there is any damage due to improper usage or modification to the luminaire.
• Failure to comply with the instructions in this manual may increase the risk of damage or injury and will void the warranty.

Installation Requirements

• All wiring and installation must adhere to the latest local and national wiring rules (e.g., AS/NZS 3000 Electrical installations). If unsure, consult a licensed electrician.
• Replace any cracked protective lamp shade to maintain the luminaire's IP rating.
• Location Selection:
  • This luminaire is suitable for deck installation only. It is not suitable for ceiling or wall installations.
  • The luminaire is protected against water penetration to IP65 standards, meaning it can withstand jets of water from any direction. This protection must be maintained during installation.
  • The wiring kit and connectors are not suitable for underground installation without protection from water or damp conditions. Position them in a location where water can easily drain away; they are not designed to be immersed in water.
  • The installation location may require a gravel substrate to aid water drainage, preventing the wiring kit and connectors from being submerged after heavy rain or garden watering.
  • The mounting point must be able to support at least 2 times the weight of the luminaire.
• Handle electrical wires with care during unpacking to avoid damaging connections.
• Lay out all components on a smooth surface and verify that all parts are present before assembly. If parts are missing, return the complete product to the place of purchase for inspection or replacement.
• Inspect the luminaire for any damage incurred during transport. Do not operate or install a product that appears damaged. Return it to the place of purchase for inspection, repair, or replacement.
• Before commencing any electrical work, ensure that power to the circuit you are working on has been switched OFF.

Installation Directions

Remove all packaging material from the product. Be careful not to discard accessories that may be hidden within the packaging.

Method 1: Installing the Deck Light with Springs

Refer to the diagram illustrations for visual guidance.

1. Remove the luminaire from its moulded box.
2. Install the springs onto the luminaire by tightening the screws on both sides. (Diagram A: Shows luminaire body and separate spring clips being attached.)
3. Cut an installation hole of 36mm diameter into the mounting point. (Diagram B: Illustrates the required hole diameter for mounting.)
4. Connect the luminaire to the Lucci wiring kit (SKU# 220826, 220827 - sold separately). Ensure the connector is fully tightened. Note: The wiring kit is rated for a maximum 80VA load only. (Diagram C: Depicts the luminaire's connector being securely plugged into the wiring kit connector.)
5. Install the luminaire into the prepared installation hole.
6. Connect the Lucci wiring kit (SKU# 220826, 220827 – sold separately) to the Lucci transformer (SKU# 220818, 220819, 220829 – sold separately). Note: Do not exceed the load limits of the Lucci wiring kit (80VA) and Lucci transformer (28VA and 10VA). (Diagram D: Shows the transformer connected to a mains plug and the wiring kit.)
7. Insert the plug into a mains power socket outlet (not included) and ensure it is fully plugged in.
8. After installation, switch on the luminaire to test all lighting functions. (Diagram E: Shows the fully installed and operational deck light.)

Method 2: Installing the Deck Light with Moulded Box

Refer to the diagram illustrations for visual guidance.

1. Remove the luminaire from its moulded box. (Diagram A: Shows luminaire body and separate spring clips being attached.)
2. Cut an installation hole of 39mm diameter into the mounting point. (Diagram B: Illustrates the required hole diameter for mounting.)
3. Install the moulded box into the prepared installation hole.
4. Connect the luminaire to the Lucci wiring kit (SKU# 220826, 220827 - sold separately). Ensure the connector is fully tightened. Note: The wiring kit is rated for a maximum 80VA load only. (Diagram C: Depicts the luminaire's connector being securely plugged into the wiring kit connector.)
5. Install the luminaire into the moulded box.
6. Insert the plug into a mains power socket outlet (not included) and ensure it is fully plugged in. (Diagram D: Shows the transformer connected to a mains plug and the wiring kit.)
7. Connect the Lucci wiring kit (SKU# 220826, 220827 – sold separately) to the Lucci transformer (SKU# 220818, 220819, 220829 – sold separately). Note: Do not exceed the load limits of the Lucci wiring kit (80VA) and Lucci transformer (28VA and 10VA).
8. Insert the plug into a mains power socket outlet (not included) and ensure it is fully plugged in.
9. After installation, switch on the luminaire to test all lighting functions. (Diagram E: Shows the fully installed and operational deck light.)

Safety Tips

• Always ensure the power is OFF and the luminaire has cooled down before performing any maintenance, cleaning, or adjustment.
• The external flexible cable or cord of this luminaire cannot be replaced. If the cable or cord is damaged, the luminaire must be destroyed.
• The luminaire must not be used if the protective shield has been cracked. Replace any cracked protective shield before using the luminaire.
• The light source of this luminaire is not replaceable. When the light source reaches its end of life, the entire luminaire shall be replaced.
• To avoid injury or damage, ensure that power leads and screws are secure before connecting the power.
• To clean, wipe with a soft damp cloth. Do NOT soak or immerse the luminaire in water or other liquids.
• Ensure that the luminaire does not come into contact with corrosive chemicals, solvents, or abrasive cleaners.

Specifications