MAULiris 826 12 LED Magnifying Lamp - Removal Instructions

Safety Information

Important Warning: The lens must be protected from sun beams to prevent a fire hazard.

• English: Lens must be protected from sun beams. Danger of fire!
• German: Lupe gegen Sonnenstrahlung abwenden. Brandgefahr!
• Russian: Лупу закрывать от солнечного излучения. Опастность возникновения пожара!

Disassembly Procedure

Base Disassembly

Step 1: Access Base Underside

Turn the lamp base upside down. The underside features five rubber feet.

[Image description: Underside of the lamp base showing five rubber feet.]

Step 2: Remove Base Screws

Locate and remove four screws on the underside of the base. A PH2 Phillips head screwdriver is required.

[Image description: Underside of the lamp base with four screws circled in red, indicating removal. A PH2 screwdriver is shown.]

Step 3: Continue Base Screw Removal

Continue removing screws from the base. A screwdriver is shown in use.

[Image description: Underside of the lamp base with a screwdriver being used to remove a screw.]

Lamp Head Disassembly

Step 4: Initial Lamp Head Screws

Focus on the lamp head. Two screws are identified for removal.

[Image description: The lamp head with two screws circled in red, indicating removal. A PH1 Phillips head screwdriver is shown.]

Step 5: Disconnect Power Connector (Push/Pull)

Inside the lamp head, a connector is shown with instructions for release. It indicates a "PUSH" action (a) and a "PULL" action (b) for disconnecting cables or components.

[Image description: Close-up of an electrical connector within the lamp head, with labels "DRÜCKEN PUSH a)" and "ZIEHEN PULL b)".]

Step 6: Power Supply Board Access

The power supply board (Art.-No.: 8261209.210) is shown, featuring a green terminal block. A PHO Phillips head screwdriver is depicted.

[Image description: The power supply board with a green terminal block. A PHO screwdriver is shown.]

Step 7: Additional Lamp Head Screws

Another view of the lamp head shows two screws to be removed with a PH1 Phillips head screwdriver.

[Image description: The lamp head with two screws circled in red, indicating removal. A PH1 screwdriver is shown.]

Step 8: Remove LED Ring Securing Screws

The LED ring assembly (Art.-No.: 8261209.200) is shown within the lamp head. Four screws securing the LED ring are circled in red, indicating removal. A PH1 Phillips head screwdriver is required.

[Image description: The lamp head showing the LED ring assembly. Four screws securing the ring are circled in red. A PH1 screwdriver is shown.]

Step 9: Detach LED Ring

The LED ring is shown being detached from the lamp head. A screwdriver is depicted.

[Image description: The lamp head with the LED ring partially detached. A screwdriver is shown.]

Step 10: Disconnect LED Ring Connector (Pull)

A connector within the lamp head is shown with a "PULL" instruction for disconnection.

[Image description: Close-up of an electrical connector within the lamp head, with the label "PULL".]

Step 11: Final LED Ring Removal

The lamp head is shown with the LED ring fully removed. A screwdriver is depicted.

[Image description: The lamp head with the LED ring removed, showing internal components. A screwdriver is shown.]

Step 12: Lamp Head Screws (PH2)

The lamp head is shown with two screws circled in red, indicating removal with a PH2 screwdriver.

[Image description: The lamp head with two screws circled in red, indicating removal. A PH2 screwdriver is shown.]

Step 13: Lamp Head Screw (PH2)

The lamp head is shown with one screw circled in red, indicating removal with a PH2 screwdriver.

[Image description: The lamp head with one screw circled in red, indicating removal. A PH2 screwdriver is shown.]

Component Identification

Component A: Power Supply Board (Art.-No.: 8261209.210)

Component B: LED Ring (Art.-No.: 8261209.200)